Re: [Amel] Maramu engine replacement


bsarff@...
 

Thanks for your input.  I'm still nervous about reducing HP but I'll look into it further.  A gain...Thanks!

----- Original Message -----
From: "Eric Lindholm" <etlindholm@sbcglobal.net>
To: amelyachtowners@yahoogroups.com
Sent: Monday, February 13, 2012 7:32:12 PM
Subject: Re: [Amel] Maramu engine replacement

 




I was going to do the same thing, but as I indicated the ZF 25 and 30 were both
unavailable for at least 4 months, and I figured it would be 6. You might want
to check on the current availability. I decided to have my trans opened up to
have it checked, and it showed almost no wear after 15 years (the original was
replaced in 1990) and 4500 hours. It takes 28 hp to drive a Maramu 6.5 knots, so
the 54 should be fine. Have fun.

Eric Maramu 105

________________________________
From: " bsarff@comcast.net " < bsarff@comcast.net >
To: amelyachtowners@yahoogroups.com
Sent: Mon, February 13, 2012 4:20:19 PM
Subject: Re: [Amel] Maramu engine replacement

 

Thanks Eric.  This is great information.   The dealer is saying that the 54 hp
engine is also a good match for replacing the 60 hp Perkins I know have.  I
don't know if this is true or not. The zf 30 is very close to the ZF 25    and
Hp rating so I'm leaning toward buying a complete engine/trans package which
will give me a 5 year warrenty on both units.  The 54 hp unit if more readily
available which is why I'm considering it. 

Does anyone have a thought on installing a 54 hp Yanmar in at Maramu? 

Thanks to everyone who has replied/commented on my inquiry.

Bob

Maramu Hin 173

----- Original Message -----

From: "Eric Lindholm" etlindholm@sbcglobal.net
To: amelyachtowners@yahoogroups.com
Sent: Friday, February 10, 2012 9:26:25 PM
Subject: Re: [Amel] Maramu engine replacement

 

Bob, I replaced my motor with the Yanmar 4JH4, and used my original
transmission, which I think is the same as yours. I had my transmission rebuilt
as needed by a local shop. I was going to get a new trans, but ZF (who bought
out Hurth) was back ordered 6 months. It ended up that by using my old trans the

installation was a lot easier. First you can use your old rear motor mounts. The

Hurth trans bolts up to an adapter plate, that will bolt directly on the Yanmar.

The rear motor mounts are mounted to this adapter plate. The Yanmar supplied
rear mounts are bolted to the engine. The Yanmar engine mounts are on 18 inch
centers, whereas the engine beds and your old mounts are on 22 1/2 inch centers.

By using your old trans and adapter plate you eliminate a lot of alignment
issues. It may be that the ZF gearbox will mount on this adapter plate, and you
could do the same thing, but I don't know. When I installed my engine, I was
able to use new rubber engine mounts (not the Yanmar, they are to tall) and the
rear mounts lined up exactly with the original Amel mounting bolts. On the front

mounts I bolted a 1/2 steel plate on the original engine bed, using the original

Amel mounting bolts, to bring it in to the 18 inch centers required for the
Yanmar engine mount alignment. The other advantage to using the original
trans is I was able to keep my shaft mounted alternator, without having to
fabricate a new mount.  If you go with a new trans, I would not go with any down

angle, as you will have to do considerable modification to the engine beds. The
front of the engine will have to be dropped about 6 inches, and you will
therefore have to remove that much of you engine beds I believe. The engine beds

have steel plates embedded in them into which the original motors mounts are
bolted. Very strong. I was able to reuse all of them. Handy. The only thing to
have to modify on the engine beds with the original trans, is the area around
the oil filter, which comes out of the right hand side, right at the level of
the top of the engine bed. You have to cut it out in a half moon shape about an
inch.

The engine swap was actually quite simple, and I can provide you with photos of
my install, if you go a similar route.

Eric, Maramu 105

________________________________
From: Bob Sarff < bsarff@comcast.net >
To: amelyachtowners@yahoogroups.com
Sent: Fri, February 10, 2012 10:14:15 AM
Subject: [Amel] Maramu engine replacement

 
I'm looking to replace my Perkins 4.154 engine with a Hurth HBW 250-3R trans
with a gear ratio of 2.74 soon and would like your opinion of a couple of
options. I know some of you have replaced your motors with the Yanmar 4JH4-TE.
Did you replace the transmission at the same time or rebuild your old one? If
you purchases a new one, which model did you purchase. My concern at this point
is that the dealer I'm working with shows transmissions that have a 7 degree
down angle and the one I have has an offset rather then a down angle.

Has anyone used the 75 hp Volvo instead of the Yanmar. Is there an
advandage/disadvantage either way?

Thanks for any advise you can provide.

Bob
S/V Chara
Hin 173

[Non-text portions of this message have been removed]

[Non-text portions of this message have been removed]






[Non-text portions of this message have been removed]

Join main@AmelYachtOwners.groups.io to automatically receive all group messages.