Re: [Amel Yacht Owners] SHARKI furling motor


Fisher, Thomas W.
 

I know mine is 12volt. Most likely yours is!! It should be controlled through a set or relays in the slide door storage, port side in the Vberth.


Tom

-----Original Message-----
From: amelyachtowners@yahoogroups.com [mailto:amelyachtowners@yahoogroups.com]On Behalf Of Roy Duddy
Sent: Wednesday, July 30, 2008 09:56
To: amelyachtowners@yahoogroups.com
Subject: RE: [Amel Yacht Owners] SHARKI furling motor



Tom,

I intend to continue to use the electric furler once I resolve the motor
issue. I didn't check the voltage on the unit. I assume it is 12 volts.
Is that correct or is it 24 volts? Anything you can offer is greatly
appreciated. Thanks.

Roy

From: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com> yahoogroups.com
[mailto: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com> yahoogroups.com] On Behalf Of Fisher, Thomas W.
Sent: Wednesday, July 30, 2008 8:40 AM
To: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com> yahoogroups.com
Subject: RE: [Amel Yacht Owners] SHARKI furling motor

Ron,

If your going to keep the electric furling unit. You might want to check
the seals on the gear box. At least the small one on the drive shaft.
The whole unit is surprisingly easy to disassemble. The seals are cheap
and easily found. I ordered a couple spares and can easily get the
numbers for those also if you like.

Tom

-----Original Message-----
From: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com> yahoogroups.com
<mailto:amelyachtowners%40yahoogroups.com>
[mailto: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com> yahoogroups.com
<mailto:amelyachtowners%40yahoogroups.com> ]On Behalf Of Roy Duddy
Sent: Wednesday, July 30, 2008 08:34
To: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com> yahoogroups.com
<mailto:amelyachtowners%40yahoogroups.com>
Subject: RE: [Amel Yacht Owners] SHARKI furling motor

Thanks Tom.

I appreciate that.

Roy

From: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com>
yahoogroups.com
[mailto: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com>
yahoogroups.com] On Behalf Of Fisher, Thomas W.
Sent: Wednesday, July 30, 2008 8:27 AM
To: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com>
yahoogroups.com
Subject: RE: [Amel Yacht Owners] SHARKI furling motor

Hi Ron,

I just over hauled the roller fuller this past winter on my sharki. The
motor did not have any markings left on it. But it was easily rebuilt at
a shop. I do have a spare motor on board that I looked to use briefly.
I'll try and remember to pull it out this weekend and look for a number
for you.

Tom Fisher

Sharki #142, "SHEILA"
Kingston, Ont, CAN.

-----Original Message-----
From: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com>
yahoogroups.com
<mailto:amelyachtowners%40yahoogroups.com>
[mailto: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com>
yahoogroups.com
<mailto:amelyachtowners%40yahoogroups.com> ]On Behalf Of Roy Duddy
Sent: Wednesday, July 30, 2008 08:21
To: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com>
yahoogroups.com
<mailto:amelyachtowners%40yahoogroups.com>
Subject: [Amel Yacht Owners] SHARKI furling motor

Listmates,

Does anyone know the specifications/Model number of the 12 volt electric
furling motor on 1985 Sharki. Mine got wet and I want to replace it. Or
in the alternative has anyone installed a roller furling unit?
Recommendations?

Thanks.

Roy Duddy

175 Route 101

Bedford, NH 03110

603-472-8500

603-472-7333 Fax

Join main@AmelYachtOwners.groups.io to automatically receive all group messages.