toggle quoted messageShow quoted text
"Nicky" from Malta is what you meant to say. I always recommend Nicky Samut in Malta for any Med rigging issues. I suspect that Nicky has a lot of air miles. During the winter season he will be in Sicily at least 2 weeks working on rigging. He has also upgraded Bamar furlers. And, Nicky is a Yacht School Preferred Vendor, the only rigger in Europe selected as a rigging Preferred Vendor.
. BTW, Nicky has sailed/crewed on most all Amel models, including a 64.
CW Bill Rouse
Yacht School - Supporting Amel Ownerswww.YachtSchool.us
720 Winnie St
Galveston Island, TX 77550
I had a few cracked wires at the main too (#117). I reported this fact to ACMO in november 2018.
Would you care to tell when you informed ACMO about this failure? Was it last year?
Thank you for you input.
Attika A54 - 117
Santos - Brazil
Em ter, 11 de jun de 2019 às 07:32, Mohammad Shirloo <mshirloo@...
I hope you guys are doing well and the engine issues are now behind you.
We are replacing all 6 shrouds at the main because ACMO had a crack in one of the original long shrouds that we found in our rig inspection last year.
They did extend a 10% discount because of this so the total shipped to Corfu was 5000 euros.
Off course you only need to upgrade the mid and lower shrouds so your pricing will be less. I did receive a complete quote for all rigging that I will forward to you shortly.
I, like you, try to do everything I can myself, which is about 90%. It’s better to make a mistake and learn while help is available. However, the cruising season in the Med is short so I do elect to use known outside people if necessary so we get to enjoy the season.
The rigging is definitely one of them, at this point, for us. So I’m flying Ricky from Malta to Corfu for 2 days to take care of the shrouds and some lighting and wind cane issues.
Enjoy Tahiti. We chartered there in 2008 and had a great time.
Mohammad & Aty
Amel 54 #099
> On Jun 10, 2019, at 10:08 PM, Porter McRoberts via Groups.Io <email@example.com> wrote:
> Dear Mohammad and Aty
> Would you be willing to let me or us know the cost from ACMO?
> This seems very tempting to do myself? Then have a rigger double check. A lot of work, yes but interesting and tempting!
> Many thanks.
> S/V IBIS 54-152
> Excuse the errors.
> Sent from my IPhone
>> On Jun 6, 2019, at 11:19 PM, ngtnewington Newington via Groups.Io <firstname.lastname@example.org> wrote:
>> Thanks guys, it looks like if I order from ACMO then it is a straight swap. So that is what I will do.
>> I have thought hard about all this and at the end of the day I do not want to have that niggling feeling that my rigging is not up to it on a dark stormy night!
>>> On 7 Jun 2019, at 11:42, Mohammad Shirloo <mshirloo@...> wrote:
>>> Hello Nick;
>>> We are currently going though the same process and we have just released the order to ACMO.
>>> If ordered from ACMO, you will receive the entire parts required for the upgrade. This includes a “stronger” pin, as ACMO puts it, the turn buckles and threaded eye. I just again reconfirmed this with ACMO. If you look at your connections at the chain plates, the parts have an ACMO stamp on them.
>>> Therefore according to ACMO, no other parts will be necessary, it is just a matter of removing the existing shrouds and installing new.
>>> I will provide an update if we find anything that contradicts this during the install.
>>> Mohammad & Aty
>>> B&B Kokomo
>>> Amel 54 #099
>>>> On Jun 7, 2019, at 7:27 AM, ngtnewington Newington via Groups.Io <email@example.com> wrote:
>>>> Further to the news that the Amel 54 should have 12mm aft lowers not 10mm and that the intermediates should be beefed up from 8mm to 10mm. I am now seriously working this out.
>>>> On the face of it I can order the replacement wire and fittings from ACMO in France and have it a week later. What worries me is that the pin sizes will increase (I guess)
>>>> This should be no problem at the bottom where there is a massive chainplate that I could drill out to accept the bigger pins but at the top at the spreader bases it will be tricky.
>>>> Has anyone been there and done this project?
>>>> What about sticking to 8mm and 10 mm but upgrading the wire quality to say Dyform? Dyform offers about 30% more strength than standard 1x19?
>>>> Any experts out there?
>>>> S/Y Amelia AML54-019
>>>> Anchored in Kefalonia enjoying easy living after 2000 mile voyage from Canary Islands.