Re: Bow Thruster Service


Peter Buckley
 

Hi All,

I had an issue with the bow thruster on my Mango. I made a jacking block similar to the Amel one and tried in vain to move it. The yacht was in the water so trying to rotate from the water was difficult. I tried everything until I spent $70+ Aust on a product called Yield. I had tried every other product with no luck. 4 squirts of Yield and they released from each other. Great product……

Try that if you can source it where you are.

Regards

Peter

-- 
Peter Buckley

83 Twelfth Avenue
Raymond Island VIC 3880

Phone: 0428 427 786

Email: carhartt@...


From: CW Bill Rouse <brouse@...>
Reply-To: <main@AmelYachtOwners.groups.io>
Date: Thu, 29 Aug 2019 07:46:50 -0500
To: <main@amelyachtowners.groups.io>
Subject: Re: [AmelYachtOwners] Bow Thruster Service

JL Mertz, CottonBay:

Yes, it should be "easy."

There are 4 Allen head bolts on most SN & SMs, but in later model SMs, 2 bolts. It is always easy if the bow thruster is serviced correctly, with seal replacement when needed, and never left DOWN while sailing. 

But, if you don't follow the above, you'll be lucky if it's easy. 


Best,

CW Bill Rouse
Amel Yacht Owners School - www.YachtSchool.us
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970

On Thu, Aug 29, 2019, 12:35 AM jlm@... <jlm@...> wrote:

Hello,

if the 4 bolts that hold the bow thruster are out it should be easy,

Drive the bow thruster simply go down, then from the outside of the boat rotate the bow thruster, possibly by a movement rotation back and forth. Always sweet ...

JL Mertz

CottonBay


Le 28/08/2019 à 20:33, Matt Salatino via Groups.Io a écrit :
Bill,
Would a heatgun provide enoughheat without affecting the FRP?

~~~⛵️~~~Matt

On Aug 28, 2019, at 10:21 AM, CW Bill Rouse <brouse@...> wrote:

Bernd,

You should be very, very careful with heat because the Bow Thruster Tube and case is made of GRP, not metal. 

The contact point is Cast Iron to the GRP tube. The problem is a result of NOT replacing the lip-seal and foam donuts, and possibly leaving the bow thruster down while sailing or motoring. Saltwater has passed through the seals and has caused corrosion on the electric motor base which is made of Cast Iron. This corrosion (Iron Oxidation) has reduced the size of the opening for the tube at the base of the motor. Your photos show that this has been more than a little saltwater over a long time, possibly months/years. It is going to be very difficult to separate the tube from the motor base. You will need the tool designed by Amel, plenty of penetrating fluid and 3-4 days of constant pressure to cause separation. You can use some light tapping or vibration on the cast iron motor base intermittently while constant pressure is applied with the special tool. But take care not to strile the base too hard because it is made of cast iron.

<image.png>
I recommend that you closely check the lower bearing on the electric motor because I suspect it is also damaged.

In the future, replace the seals every 2 years...also replace the 0.3 liters of 80/90 Gear Oil when you replace the seals. Always use plenty of waterproof grease at the contact points of the tube and motor base.

This is the normal materials needed for service every 2 years (contact SAV"at"Amel.fr):
<image.png>
You will certainly get other advice, but I firmly believe that you will not get better advice.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Aug 28, 2019 at 12:03 PM Matt Salatino via Groups.Io <helmsmatt=yahoo.com@groups.io> wrote:
A little heat?

~~~⛵️~~~Matt

On Aug 28, 2019, at 9:44 AM, "jlm@..." <jlm@...> wrote:

Hi !

I had the  same problem ... You need a lot of patience, mutch WD40 and patience, do not forcing, do not break the threads, the contact is bronze on stainless  ...

I needed 2 days ...

good luck

JLM

CottonBay


Hold time 2 or 3 days with WD40, WD40 and much

Le 28/08/2019 à 18:35, Bernd Spanner a écrit :
Hello,
I wanted to change the seal on the bow thruster today.
Unforunately after removing the 4 screws I could not get the shaft disconnected. It’s badly rusted all over. Any ideas how I can loosen it?? Already used some wd40 & caramba to get it loose.... no success 
Pics attached
Best regards, 
Bernd
SN 119 / Cascais, Portugal

Garanti sans virus. www.avast.com

Join main@AmelYachtOwners.groups.io to automatically receive all group messages.