Re: No steering parts, rack & pinion, cables, from Amel

hanspeter baettig

Hi Peterr,Bill and Danny
I totally also agree
I got my new steering systems in one week (rack and pistons) from Amel.
Easy to install , 3 houres,
And Bill , i shall send you a email, how it was done here in Trinidad.
Tamango 2, SM16

------ Original Nachricht ------
Am Samstag, 5. Okt, 2019 um 23:13, Peter Forbes schrieb:

I totally agree and am having lots of work done on Carango by AMEL in La Rochelle.

Let’s support them to support us.


Peter Forbes
AMEL 54 #035
La Rochelle 

0044 7836 209730

On 5 Oct 2019, at 19:30, Danny and Yvonne SIMMS <simms@...> wrote:

Hi Bill and all. I totally agree. If we want Amel to continue to provide spares for boats 15,20,30 and 40 years old they must be our first port of call for parts. This service is a colosall commitment on their part and I believe unique in the marine world. They cannot provide this service without throughput. That is down to us. We might get something "cheaper" elsewhere but long term the loss of this service would be very expensive. 

Use it or lose it as they say.

Kind Regards from that little bit of heaven called Fiji


SM 299

Ocean Pearl

On 06 October 2019 at 02:14 CW Bill Rouse <brouse@...> wrote:


Because you reported that Amel will no longer supply these parts, I contacted the US distributor, who said they would get in touch with the Italy headquarters.

I also wrote Amel to verify that they will not supply these parts. If Amel replies that they will supply parts, I will drop my efforts with the manufacturer because I firmly believe that we should support Amel. Frankly, had I known that you had requested parts from any source other than La Rochelle, I would have never contacted the distributor.

Now, I really wonder who you spoke to because the comment that when we have time, we will work on a hydraulic solution," seems very un-Amel to me. Maybe you spoke to the wrong person. In either case, hopefully I will have a response from SAV manager shortly. 


CW Bill Rouse
Amel Yacht Owners School -
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970

On Sat, Oct 5, 2019, 6:56 AM Eamonn Washington < eamonn.washington@...> wrote:
Thanks guys for your welcome input!

I have the Ultraflex M61 FT25 C42M cables.

Although the steering quadrant had no loose nuts and the 2 cables connected to it were well greased, I did notice a problem that I never noticed before and it probably was not there a year ago (maybe this is what Danny referred to).  Both cables leave their plastic sheath and are screwed into shafts with large adaptor nuts; these shafts in turn are screwed through what I would call a ball and socket joint to go through the last bulkhead on the port side just about 30cm before the steering quadrant itself, where they are connected to the quadrant.  In my case, the aft cable shaft had unscrewed itself about 2cm through the ball and socket joint towards the quadrant; I could see the grease mark where it previously was.  I was easily able to turn it back and it made a huge difference, both steering to port and starboard.  If anything, steering to starboard is slightly harder now.  I noticed there is about 1cm of play in the steering wheel.

Then I disconnected the autopilot drive unit and removed the chain from the wheel sprocket.  That eliminated some noise and I guess minimal friction.  It made no difference to the steering feel, but I could concentrate on the remaining noise better.

I noticed that every time there is a change of direction when turning the wheel, there is a quiet clunk (around the 1cm of play on the wheel).  This is regardless if the wheel is already turned to port or starboard or centered.  It might be normal, I don’t know.  I also noticed that the one of the cables moves in or out of the tube containing the rack a couple of mm when the wheel changes direction.  All this while tied up in a marina with no currents.

All in all, I don’t think my situation is as bad as I feared, the wheel is much lighter now, but I would still like to have the new racks and cables.  Nevertheless, the point of this thread to is to establish how we can get these critical spares going forward, knowing exactly what to order from Ultraflex seems to be the way to go (unless Amel takes up the reins again).  I appreciate Bill contacting Amel on our behalf ... I was dealing with Mediterranean sales, I guess Bill has a better network inside Amel.

Also it would be great if Eric or someone could confirm what Jean-Pierre wrote for the Santorin also applies for the Super Maramu, that the rack is 33014R (with T58 steering system trav. 230 ... not sure what that is).

I will contact Steve offline for help dismantling the rack and pinion system, to inspect it further.


Eamonn Washington
Travel Bug
Super Maramu #151
Currently in Denia, Spain.



Join to automatically receive all group messages.