Re: Oil Pressure Volvo D3 I - C


Matt Salatino
 

Our new Volvo Penta D-3 has 4.48 bar at 1800 rpm. You might be OK.

~~~⛵️~~~Matt

On Sep 6, 2020, at 10:48 AM, Dirk Hooff <sypenelope@...> wrote:

Hi Paul, Ralph, Mohammad and Arno,

thank you for your answers and your experience.

We connected an external gauge and the pressure is with cold engine at 2bar at 700rpm (idle) and 4bar at 1500rpm.
After 15min. with normal oil temperature (75degree) the oil pressure drops to 1.3bar when idling.
And 3 bar at 1500rpm.
The Volvo expert thinks, that this is not enough.
Actually the oil pressure sensor should not trigger before the oil pressure drops down to 0.7bar. That´s why I think the old sensor is too sensitive… 

First I will try it with a new sensor… unfortunately it needs time to get it, and maybe someone of you have some experience with the oil-pressure with a warm engine…

Thanks and take care,

Dirk


Am 03.09.2020 um 11:13 schrieb Paul Dowd and Sharon Brown <paul.dowd@...>:

Dirk,
 
I just had the same problem. Connecting an external gauge the pressure is normal, so I’m getting a new sensor. Note also that you cannot use a normal Volvo sensor, you must get the specially modified one that takes the bonding connection from Gwen Marine Service in France - €78.
 
Cheers,
Paul
S/Y Ya Fohi - Amel 54 #98 - Grenada
 
From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Dirk Hooff
Sent: 02 September 2020 12:44
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Oil Pressure Volvo D3 I - C
 
Hi all,
 
since yesterday I have an oil pressure problem on my AMEL 54#96.
When I go from normal speed to idle, the oil alarm starts.
Of course, this doesn´t happen in the port but between the islands in Croatia.
My German Volvo expert suspects that the oil is too thin.
Diesel has probably gotten into the oil.
That´s why I changed the oil. More than 7 liters of very thin oil came out.
Then the engine ran again without an oil pressure alarm.
But today, when I switched back to idle, the alarm went on again.
I appreciate any advice or experiences.
Thanks a lot,


Dirk


AMEL 54#96 PÉNÉLOPE
Currently Croatia close to Dubrovnik






 
Am 01.09.2020 um 16:21 schrieb Courtney Gorman via groups.io <Itsfun1@...>:
 
You need a Puller it's much safer 

but if push comes to shove I hammered mine out with a blank and mini sledge

-----Original Message-----
From: ngtnewington Newington via groups.io <ngtnewington@...>
To: main@AmelYachtOwners.groups.io
Sent: Tue, Sep 1, 2020 8:52 am
Subject: [AmelYachtOwners] Main furling motor and gear on 54

I know this has come up before, but I am servicing the main sail furling motor and worm drive. 
It is all well but the top shaft seal should be replaced. 
Problem;
Shaft into the worm gear is very tight. Soaked it in diesel for some hours, hesitant to hit it. Plan to find a press to press it out. 
Does anyone have a better idea?
Nick
S/Y Amelia
Leros.
AML 55-019
 
 
 


-- 
Cheers
Paul
Ya Fohi - Amel 54 #98

Join main@AmelYachtOwners.groups.io to automatically receive all group messages.