Re: Engine Mounts and Decoupling Vetus/Engine Block

Rudolf Waldispuehl

Thank you Bill


I have not seen something similar in the AMEL 54 Unser’s Manual not in the AMEL Owner’s Guide.

Nevertheless your information is welcomed and a good starting point, and I will take out one before ordering so I’m sure.


Best regards



Von: "" <> im Auftrag von CW Bill Rouse <brouse@...>
Antworten an: "" <>
Datum: Mittwoch, 28. April 2021 um 23:48
An: "" <>
Betreff: Re: [AmelYachtOwners] Engine Mounts and Decoupling Vetus/Engine Block




The issue is that so many things changed during the production of the 54, I cannot be sure, but I know the 54 started with 6 each Vetus K50 motor mounts as shown in the Amel 54 Users Manual.


CW Bill Rouse Amel Owners Yacht School

Address: 720 Winnie, Galveston Island, Texas 77550 


View My Training Calendar



On Wed, Apr 28, 2021 at 4:36 PM Rudolf Waldispuehl <Rudolf@...> wrote:

Dear Amelians


I’m in the process to change Engine Mounts and not sure what type or brand of Mounts where originally used on the A54 with the Volvo D3-110.

Somebody told me that Amel used on the Amel54 with the Volvo D3-110C the Volvo Mounts. I’m not sure and can’t identify which type and brand are installed on Wasabi.


Maybe somebody knows which model/type originally are installed. Otherwise I’m confident that Bill Rouse knows it. 😉

@Bill; I haven’t found any reference in your AMEL School Book.


Best regards



A54 #55



Von: "" <> im Auftrag von Herbert Lackner <herbert@...>
Antworten an: "" <>
Datum: Sonntag, 9. Februar 2020 um 11:01
An: "" <>
Betreff: Re: [AmelYachtOwners] Engine Mounts and Decoupling Vetus/Engine Block


Woody,  search for "alignment" in the forum and you will find a lot of information, also what kind of mounts you need

a summary with info from Olivier:

in order to re-align your engine with the C-drive, you need a fixed coupling as on the pictures and drawing.

You don't need to install the shaft alternator pulley while checking alignment. 


Before touching the tools, make pictures and take notes (measurements of all the fittings, position of the nuts on the rubber mounts, position of the engine on the steel cradle, position of the shaft brake disc, etc...).

Start with disconnecting the hoses that could prevent you from moving the engine backwards on its cradle.

Then undo the coupling bolts and the engine steel supports' bolts (attaching the engine on the steel cradle).

Then move the engine backwards enough to remove the coupling bolts.


Then comes the alignment process.

AMEL uses a tool which is a steel coupling machined so that its aft side "enters" the gear-box flange (see pictures and drawing). You can also pre-install the new coupling and adjust the position of the mounts.

First bring the engine forward and make sure the coupling is centered with the gear-box flange, and can enter the gap in the flange. 

Then move the engine a little bit backwards and check that the gap between the flange and the aft side of the coupler is even all around the circumference. To adjust this, you need "thickness wedges" (used in the automotive industry) and play with the rubber mounts nuts to make the gap even.

Then bring the engine forward and tighten the bolts on the cradle and on the mounts.


The advantage of using the tool AMEL uses is that it is easier to install while checking the gaps.

If you need to make one, here's a drawing of the alignment tool for a YANMAR 4JH3-HTE.

The inside diameter (C-drive input shaft) is 35 mm.

The outside diameter is 100 mm.

The diameter of the part that enters the gear-box flange cylindric gap is 62.8 mm, thickness 3 mm.


You should use a VETUS fixed coupling for 35mm shafts, then have it machined to make the 62.8mm "plug" and drilled for the four bolts that should match the flange holes.

The process is the same for Santorins or for Super Maramus.

more info from me: 
* Amel does not sell the alignment tool, I had it made by a machine shop from Aluminium
* I would change also the C-Drive mounts when you change the engine mounts.
* Make sure that the c-drive is "open" and "sits on his rubber sleeve" before you do the engine alignment.
* I used a tool like this to lift the engine . the job can be done by one person

fair winds, herbert

Join to automatically receive all group messages.