Date   

Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

sailormon <kimberlite@...>
 

Dilute hydrochloric acid works on rust if you can somehow isolate the liquid from the boat.

Fair Winds

Eric

Kimberlite SM 376

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...] On Behalf Of karkauai@...
Sent: Friday, March 28, 2014 3:04 PM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

 

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL


Re: [Amel Yacht Owners] Prop Shaft Electrolysis

sailormon <kimberlite@...>
 

Wow !!

That looks awful.

I use a galvanic isolator on my AC circuit and also have the pedestal turned on only one day a week. So far in 3 months in the marina in the Caribbean I have used one kilowatt of electric.

There is a small zinc on the line cutter, and of course the 2 big ones on the rudder.

I am very sorry for the condition of your prop shaft. I believe there should be a drawing of your c drive in the owners manual . I believe replacing the shaft is a big project. It is also possible that a neighbor is putting AC into the water.

Did you have the marina check your AC outlet on the pedestal and the water around your boat?

Fair Winds

Eric

Kimberlite SM 376

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...] On Behalf Of karkauai@...
Sent: Friday, March 28, 2014 3:01 PM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Prop Shaft Electrolysis

 

 

I have just hauled Kristy out to repaint the bottom after 2 1/2 years.  She's been sitting in the water in a marina at Brunswick GA for the last 2 years where I've hired a diver to clean the bottom and replace the zincs as needed every 4-6 weeks.  I was surprised to see no zinc on the prop when we hauled out, and dismayed to see severe electrolytic corrosion of the prop shaft when I started changing the seals. I posted a pic at the KristySM243 folder https://groups.yahoo.com/neo/groups/amelyachtowners/photos/albums/948071197/lightbox/1877878820
I need advice on what is involved in removing the prop shaft.  Is it necessary to remove the bottom of the drive aft of the keel?
I guess I'm going to look into isolating the boat electrically.
Sigh,
Kent
SM243
Currently Tiger Point Marina, Fernandina Beach, FL


Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

karkauai
 

What does everyone think about Hydrochloric acid?  No damage to the hull?  Fumes?  How to get rid of it afterward?

Not sure what the heat gun would do???

I don't understand what you're talking about with electrolysis?

Thanks, Roque,
Kent


On Mar 28, 2014, at 8:17 PM, Roque <ediroque@...> wrote:

 

Alternatives to think about:


1. Hydrochloric acid;

2. Heat gun;

3. Electrolysis (maybe you won't have enough room  for this) 

Roque
S/Y Atica Amel 54

Em sexta-feira, 28 de março de 2014, Kent Robertson <karkauai@...> escreveu:
 

Been there and done that.  Such a small access that I'm bruised on the arm and ribs from squeezing in there.
I hit the mass with a 5 lb hammer and nothing budges!
Keep em coming!
Kent


On Mar 28, 2014, at 7:16 PM, Ann-Sofie Svanberg <kanalmamman@...> wrote:

 

Sledge hammer???

/Annsofie
Lady Annila SM 232

Skickat från min iPad

28 mar 2014 kl. 18:50 skrev "Kent Robertson" <karkauai@...>:

 

Never heard of that product Mark, but I'll see if I can find it.  Soda blasting would only hot the surface, but maybe could help a bit at a time.
Keep those ideas coming!
Thanks,
Kent


On Mar 28, 2014, at 6:21 PM, Mark Erdos <mcerdos@...> wrote:

 

Another thought. Since you are in a yard - soda blasting? It would be a mess to clean up but it would probably do the trick.

Mark
SM2K #275



On Fri, Mar 28, 2014 at 5:36 PM, Kent Robertson <karkauai@...> wrote:
 

Problem is getting the old one out of the chain locker.  It won't budge because it's all rusted together.  The limited access to the locker means the fix has to be chemical rather than mechanical. Acid would probably do it but fumes from muriatic acid would every toxic.  I soaked it vinegar for 24 hrs and no improvement.
Need some other suggestions.
Kent
SM243 Kristy
Tiger Point Boat Yard
Fernandina Beach FL



On Mar 28, 2014, at 3:30 PM, "haspeter.baettig" <hanspeter.baettig@...> wrote:

 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL



Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

Roque
 

Alternatives to think about:

1. Hydrochloric acid;

2. Heat gun;

3. Electrolysis (maybe you won't have enough room  for this) 

Roque
S/Y Atica Amel 54

Em sexta-feira, 28 de março de 2014, Kent Robertson <karkauai@...> escreveu:

 

Been there and done that.  Such a small access that I'm bruised on the arm and ribs from squeezing in there.
I hit the mass with a 5 lb hammer and nothing budges!
Keep em coming!
Kent


On Mar 28, 2014, at 7:16 PM, Ann-Sofie Svanberg <kanalmamman@...> wrote:

 

Sledge hammer???

/Annsofie
Lady Annila SM 232

Skickat från min iPad

28 mar 2014 kl. 18:50 skrev "Kent Robertson" <karkauai@...>:

 

Never heard of that product Mark, but I'll see if I can find it.  Soda blasting would only hot the surface, but maybe could help a bit at a time.
Keep those ideas coming!
Thanks,
Kent


On Mar 28, 2014, at 6:21 PM, Mark Erdos <mcerdos@...> wrote:

 

Another thought. Since you are in a yard - soda blasting? It would be a mess to clean up but it would probably do the trick.

Mark
SM2K #275



On Fri, Mar 28, 2014 at 5:36 PM, Kent Robertson <karkauai@...> wrote:
 

Problem is getting the old one out of the chain locker.  It won't budge because it's all rusted together.  The limited access to the locker means the fix has to be chemical rather than mechanical. Acid would probably do it but fumes from muriatic acid would every toxic.  I soaked it vinegar for 24 hrs and no improvement.
Need some other suggestions.
Kent
SM243 Kristy
Tiger Point Boat Yard
Fernandina Beach FL



On Mar 28, 2014, at 3:30 PM, "haspeter.baettig" <hanspeter.baettig@...> wrote:

 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL



Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

karkauai
 

Been there and done that.  Such a small access that I'm bruised on the arm and ribs from squeezing in there.
I hit the mass with a 5 lb hammer and nothing budges!
Keep em coming!
Kent


On Mar 28, 2014, at 7:16 PM, Ann-Sofie Svanberg <kanalmamman@...> wrote:

 

Sledge hammer???

/Annsofie
Lady Annila SM 232

Skickat från min iPad

28 mar 2014 kl. 18:50 skrev "Kent Robertson" <karkauai@...>:

 

Never heard of that product Mark, but I'll see if I can find it.  Soda blasting would only hot the surface, but maybe could help a bit at a time.
Keep those ideas coming!
Thanks,
Kent


On Mar 28, 2014, at 6:21 PM, Mark Erdos <mcerdos@...> wrote:

 

Another thought. Since you are in a yard - soda blasting? It would be a mess to clean up but it would probably do the trick.

Mark
SM2K #275



On Fri, Mar 28, 2014 at 5:36 PM, Kent Robertson <karkauai@...> wrote:
 

Problem is getting the old one out of the chain locker.  It won't budge because it's all rusted together.  The limited access to the locker means the fix has to be chemical rather than mechanical. Acid would probably do it but fumes from muriatic acid would every toxic.  I soaked it vinegar for 24 hrs and no improvement.
Need some other suggestions.
Kent
SM243 Kristy
Tiger Point Boat Yard
Fernandina Beach FL



On Mar 28, 2014, at 3:30 PM, "haspeter.baettig" <hanspeter.baettig@...> wrote:

 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL



Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

Ann-Sofie Svanberg <kanalmamman@...>
 

Sledge hammer???

/Annsofie
Lady Annila SM 232

Skickat från min iPad

28 mar 2014 kl. 18:50 skrev "Kent Robertson" <karkauai@...>:

 

Never heard of that product Mark, but I'll see if I can find it.  Soda blasting would only hot the surface, but maybe could help a bit at a time.
Keep those ideas coming!
Thanks,
Kent


On Mar 28, 2014, at 6:21 PM, Mark Erdos <mcerdos@...> wrote:

 

Another thought. Since you are in a yard - soda blasting? It would be a mess to clean up but it would probably do the trick.

Mark
SM2K #275



On Fri, Mar 28, 2014 at 5:36 PM, Kent Robertson <karkauai@...> wrote:
 

Problem is getting the old one out of the chain locker.  It won't budge because it's all rusted together.  The limited access to the locker means the fix has to be chemical rather than mechanical. Acid would probably do it but fumes from muriatic acid would every toxic.  I soaked it vinegar for 24 hrs and no improvement.
Need some other suggestions.
Kent
SM243 Kristy
Tiger Point Boat Yard
Fernandina Beach FL



On Mar 28, 2014, at 3:30 PM, "haspeter.baettig" <hanspeter.baettig@...> wrote:

 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL



Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

karkauai
 

Never heard of that product Mark, but I'll see if I can find it.  Soda blasting would only hot the surface, but maybe could help a bit at a time.
Keep those ideas coming!
Thanks,
Kent


On Mar 28, 2014, at 6:21 PM, Mark Erdos <mcerdos@...> wrote:

 

Another thought. Since you are in a yard - soda blasting? It would be a mess to clean up but it would probably do the trick.

Mark
SM2K #275



On Fri, Mar 28, 2014 at 5:36 PM, Kent Robertson <karkauai@...> wrote:
 

Problem is getting the old one out of the chain locker.  It won't budge because it's all rusted together.  The limited access to the locker means the fix has to be chemical rather than mechanical. Acid would probably do it but fumes from muriatic acid would every toxic.  I soaked it vinegar for 24 hrs and no improvement.
Need some other suggestions.
Kent
SM243 Kristy
Tiger Point Boat Yard
Fernandina Beach FL



On Mar 28, 2014, at 3:30 PM, "haspeter.baettig" <hanspeter.baettig@...> wrote:

 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL



Re: [Amel Yacht Owners] Feeling secure

Ann-Sofie Svanberg <kanalmamman@...>
 

Very nice done! What a good idea!

But we can't figure out the lock solution. Can you post a better picture on that?

Regards
Annsofie & Jonas
S/Y Lady Annila. SM 232

Skickat från min iPad

28 mar 2014 kl. 10:42 skrev gegcarter@...:

 

I have just posted photos of our new security system for the companionway. As you can see the feature can be used both when leaving the boat as a extra strength to locking the companionway and when inside the boat if you want air and wish to leave the companionway open but feel you are staying in perhaps a potentially unsafe anchorage.
Arcglow in Almerimar (Spain) can be contacted by email, arcglow@..., if anyone is interested.

Keith
on Guma


Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

Mark Erdos
 

Another thought. Since you are in a yard - soda blasting? It would be a mess to clean up but it would probably do the trick.

Mark
SM2K #275



On Fri, Mar 28, 2014 at 5:36 PM, Kent Robertson <karkauai@...> wrote:
 

Problem is getting the old one out of the chain locker.  It won't budge because it's all rusted together.  The limited access to the locker means the fix has to be chemical rather than mechanical. Acid would probably do it but fumes from muriatic acid would every toxic.  I soaked it vinegar for 24 hrs and no improvement.
Need some other suggestions.
Kent
SM243 Kristy
Tiger Point Boat Yard
Fernandina Beach FL



On Mar 28, 2014, at 3:30 PM, "haspeter.baettig" <hanspeter.baettig@...> wrote:

 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL



Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

Mark Erdos
 

Kent,

What about something like Boeshield RustFree Rust and Stain Remover? Perhaps a multiple application to a specific area will give you the break you need to get the ball small enough.

Mark
SM2K #275



On Fri, Mar 28, 2014 at 5:36 PM, Kent Robertson <karkauai@...> wrote:
 

Problem is getting the old one out of the chain locker.  It won't budge because it's all rusted together.  The limited access to the locker means the fix has to be chemical rather than mechanical. Acid would probably do it but fumes from muriatic acid would every toxic.  I soaked it vinegar for 24 hrs and no improvement.
Need some other suggestions.
Kent
SM243 Kristy
Tiger Point Boat Yard
Fernandina Beach FL



On Mar 28, 2014, at 3:30 PM, "haspeter.baettig" <hanspeter.baettig@...> wrote:

 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL



Re: [Amel Yacht Owners] Feeling secure

karkauai
 

That's a very creative way of solving that issue Keith.  I'm impressed.
Kent


On Mar 28, 2014, at 10:42 AM, <gegcarter@...> wrote:

 

I have just posted photos of our new security system for the companionway. As you can see the feature can be used both when leaving the boat as a extra strength to locking the companionway and when inside the boat if you want air and wish to leave the companionway open but feel you are staying in perhaps a potentially unsafe anchorage.
Arcglow in Almerimar (Spain) can be contacted by email, arcglow@..., if anyone is interested.

Keith
on Guma


Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

karkauai
 

Problem is getting the old one out of the chain locker.  It won't budge because it's all rusted together.  The limited access to the locker means the fix has to be chemical rather than mechanical. Acid would probably do it but fumes from muriatic acid would every toxic.  I soaked it vinegar for 24 hrs and no improvement.
Need some other suggestions.
Kent
SM243 Kristy
Tiger Point Boat Yard
Fernandina Beach FL



On Mar 28, 2014, at 3:30 PM, "haspeter.baettig" <hanspeter.baettig@...> wrote:

 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL


Re: [Amel Yacht Owners] Rusted Ball of Chain in the Chain Locker

hanspeter baettig
 

Hi Kent
buy a new one, safety first
best regards
Hanspeter
Tamango 2 , SM #16
Krusadasi, Turkey
(actual with out twitter and youtube, mr erdogan, Prminister of Tukey is a littel bit angry :-)
I think to leave Turkey, Greek is only a few miles away

Von meinem iPhone gesendet

Am 28.03.2014 um 20:03 schrieb <karkauai@...>:

 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL


Rusted Ball of Chain in the Chain Locker

karkauai
 

I've also discovered that the last 100ft or so of my anchor chain is rusted into a huge solid mass in the chain locker.  I've sprayed a ton of PB Blaster on it and beat it with a hammer without much success.  Right now I'm soaking it in Vinegar.
Any ideas?
Thanks,
Kent
SM 243 Kristy
Currently Tiger Point Marina Fernandina Beach, FL


Prop Shaft Electrolysis

karkauai
 

I have just hauled Kristy out to repaint the bottom after 2 1/2 years.  She's been sitting in the water in a marina at Brunswick GA for the last 2 years where I've hired a diver to clean the bottom and replace the zincs as needed every 4-6 weeks.  I was surprised to see no zinc on the prop when we hauled out, and dismayed to see severe electrolytic corrosion of the prop shaft when I started changing the seals. I posted a pic at the KristySM243 folder https://groups.yahoo.com/neo/groups/amelyachtowners/photos/albums/948071197/lightbox/1877878820
I need advice on what is involved in removing the prop shaft.  Is it necessary to remove the bottom of the drive aft of the keel?
I guess I'm going to look into isolating the boat electrically.
Sigh,
Kent
SM243
Currently Tiger Point Marina, Fernandina Beach, FL


Feeling secure

gegcarter@...
 

I have just posted photos of our new security system for the companionway. As you can see the feature can be used both when leaving the boat as a extra strength to locking the companionway and when inside the boat if you want air and wish to leave the companionway open but feel you are staying in perhaps a potentially unsafe anchorage.
Arcglow in Almerimar (Spain) can be contacted by email, arcglow@..., if anyone is interested.

Keith
on Guma


Re: [Amel Yacht Owners] Eno Stove rebuild and parts availability

sailormon <kimberlite@...>
 

Bill,

Would you please email me the stove photos and instructions as to how to replace the igniter?

On my computer half of what you wrote is cut off.

Fair Winds

Eric

Kimberlite SM 376

 

Kimberlite@...

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...] On Behalf Of yahoogroups@...
Sent: Thursday, March 27, 2014 7:55 AM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Eno Stove rebuild and parts availability

 

 

All,

 

I removed and cleaned, rebuilt, and replaced old/worn parts on the Eno stove. I am sure that you are aware that it is out of production. I was successful in finding parts for a rebuild of our Eno 4 burner stove at www.socal.co.uk

 

I purchased the following:

Burner caps: 

Burner pots: 

Be sure to get these Burner Fixing Stud and Screw (set of two studs)...1 set for each burner...the old ones break easily: 

 

Electronic Ignition:

Plastimo Cooker Spare Electronic Ignition Unit 6 Outlet 

 

We also purchased new burner knobs and a new oven knob.

 

The above website index does not work well...you cannot search on part number and you cannot get good results searching by part name. It took me a while to find these parts. They have more parts such as knobs, burner tops, etc. 

 

If you get frustrated with trying to find the part you need, I suggest that you email Peter"at"socal.co.uk, with a photo of the part, Brand and model of the stove,

and possibly dimensions...something like this: Eno 4 burner stove produced 2002, 

100mm black porcelain burner cap with two holes...see photo."



You will find lots of instructions that I documented in this album: https://groups.yahoo.com/neo/groups/amelyachtowners/photos/albums/20069970

 

Bill

BeBe 387


New file uploaded to amelyachtowners

amelyachtowners@...
 

Hello,

This email message is a notification to let you know that
a file has been uploaded to the Files area of the amelyachtowners
group.

File : /Eno Owners manual and parts list.pdf
Uploaded by : alan_leslie_elyes_sm2k <divanz620@...>
Description : Parts List for Eno 4 burner Bretagne

You can access this file at the URL:
https://groups.yahoo.com/group/amelyachtowners/files/Eno%20Owners%20manual%20and%20parts%20list.pdf

To learn more about file sharing for your group, please visit:
https://help.yahoo.com/kb/index?page=content&y=PROD_GRPS&locale=en_US&id=SLN15398

Regards,

alan_leslie_elyes_sm2k <divanz620@...>


Re: Eno Stove rebuild and parts availability

Alan Leslie
 

I've just posted the parts list - diagram and numbers for the ENO 4 burner Bretagne.


Cheers

Alan

SV Elyse SM437


Re: [Amel Yacht Owners] Steerring Wheel Cover

Mark Erdos
 

I'll be right there! 

Just got the SSB up and running - yeah! I still have a little RFI on the AIS. I need to move the AIS antenna away from the SSB antenna and install a couple of ferrites. All is good.

Cream Puff
SM2K #275


On Thu, Mar 27, 2014 at 12:02 PM, <yahoogroups@...> wrote:
 

Mark,


I was in a sewing shop/bimini maker/sail loft today and they were making a new leather cover for a helm wheel. I know Turkey is a long way from you, but possibly this will give you an idea of where to look and price comparison.

I will try to get a price here for your comparison.

Bill
BeBe 387