Date   

Re: [Amel Yacht Owners] Interior Upholstery

Germain Jean-Pierre <jgermain@...>
 

Hello Chris,

I toyed with similar ideas to yours for the dining table but as Bill said, you would be better off with good cockpit cushions.  A friend owned an SM; he and his squeeze always slept in the cockpit when underway.

They had top drawer cockpit covers made back to the mizzen and added both side covers and mosquito netting.

I went as they did… TOTMBO attracts mosquitos… !

Cheers,


Jean-Pierre Germain
SY Eleuthera, SM 007



On 24 Feb 2015, at 04:40, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Bill,

I'll run that up the mast tonight and see how it flies  

Chris

 
 

On 24-02-2015 13:06, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 
 

Chris,

You have not spent many nights on that SM. At some point, the flopping stopped bothering us...We don't even hear it. It is not worth tampering with the table...just my opinion.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:54 PM, "Chris Flack chris@... [amelyachtowners]" <amelyachtowners@...> wrote:
 
 

Thanks Bill,

The bed was really for us to use when the 'plopping' at the stern became too much (Jennifer is a light sleeper) and also for more air BUT for 2400 euro might be a better proposition to get more of the upholstery done and new curtains (those concertina type)

I have asked Riza for a quote on the cockpit cushions and also for the space atop the aft cabin.

 

Cheers again
Chris

 
 
 

On 24-02-2015 12:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 
 

Chris,

Thanks. 

I do not think that I would try to make the dining table collapsible for another berth. If you are in a situation where all of the bunks are full, two people can sleep comfortably in the cockpit...invest in cockpit cushions instead...you will be happier.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:21 PM, "Chris Flack chris@... [amelyachtowners]" <amelyachtowners@...> wrote:
 
 

Yes Bill - you will not get the support under your thighs/knees will you? Yes, better to keep that bull nose.

Jennifer said to say that you and the others in the group have gone to an awful lot of trouble to guide us.

Cheers

Chris

 
 

On 24-02-2015 10:19, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 
 
Chris if you change the depth of that seat cushion, you will wind up with an uncomfortable seat.
 
Bill

On Mon, Feb 23, 2015 at 3:49 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 
 

Hi Bill,

I have sent these photos through to Jennifer to show her how smart it looks. It is definitely a great facelift and looks ultra-comfortable.

With the bull nose on the front of the seat, it may not work with my plan to turn the lowered dining table into a bed and will have to think about keeping that section flat. I also hadn't thought of doing the nav seat but it would be so much better if we did.

Thanks for the extra effort you are putting in to help us out.

 

Cheers
Chris Flack
Hemera SM031

 
 
 

On 24-02-2015 08:31, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 
 
Chris,
 
Look closely at the photos. 
 
The seats and back style was changed with the "channel quilting" removed. The back also has an added interior zipper (like the seat does) which gives it that look of a pillow at the top of the back and a bull nose on the front of the seat...see photo "RF Back Detail" and "LF Seat Detail"
 
Also look at the very large circular back...it has been split into 3 pieces. Look at the photo labeled "LF Corner" and "RF Corner" which show the split. You can also see how the original seat was made by first removing the piece of foam from the backside of the seat cushion. Once removed, you will see an internal zipper which when opened reveals the bull nose piece of foam.
 
I would use UltraLeather Ivory also. Tomorrow I am going to visit their distributor in Houston, I will try to get a sample that I can mail to you.
 
Bill
BeBe

On Mon, Feb 23, 2015 at 2:51 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 
 

Thank you Bill,

I asked Riza to use the UltraLeather Ivory on our refit with the memory foam layer and to also make up a 2 section insert for the dining table when we drop it down to a bed. Getting really excited about the things we are doing and can't wait to get over there at the beginning of May.

 

Cheers
Chris Flack
HemeraSm031

 
 

On 24-02-2015 00:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 
 
Chris:
 

  Ultrafabrics Europe, Ltd

19 The Warren,
East Goscote,
Leicestershire, LE7 3XA
United Kingdom

Main Phone: +44.116.260.9625
Email: ufe@...

On Sun, Feb 22, 2015 at 10:08 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 
 

Bill, thanks you again.

This is very interesting and the Ivory does look good. Not too sure between the UltraLeather and the UltraLeather Pro.

I hope Riza is able to source it for me.

I hope your folk up there are starting to thaw out.

 

Cheers
Chris
Hemera SM031

 
 

On 23-02-2015 11:18, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 
 
Chris,
 
Alcantara and Ultrasuede are two of the best known brands for a fabric that has a polyester fiber electrostatically glued to a base cloth. The result is a fabric that looks like a perfect leather suede. There are many qualities and prices. I am not sure which brand Amel used on the SM 2000.
 
Polyester fiber is easily cleaned with soap and water, but will also take alcohol type cleaners for tough grease stains. Polyurethane coated fabrics are harder to stain, will clean with soap and water and you need to test alcohol or petroleum-based cleaners need to be tested on Polyrethane, because they may dull the luster. 
 
If I were changing, I would probably use Ultraleather™ Color Ivory https://www.ultrafabricsllc.com/Site/Swatch/30/ 
<<>> Ultraleather™ Pro Color Swan https://www.ultrafabricsllc.com/Site/Swatch/597/
 
I will upload a few photos of the interior of SM ARAMIS...hopefully the owner will not mind. It is beautiful!
 
Bill
BeBe 387
 
 

On Sun, Feb 22, 2015 at 4:16 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 
 

Hi Bill,

I didn't know your past history but your advice is again, invaluable. 

Is the polyester microfiber fabric that Amel use the Alcantara? Does the Ultraleather clean up well from possible grease and stains?

Some photos and details of what you have described would be great thank you. The idea of the memory foam would add even greater comfort. We are also looking at turning the thinking table into a drop down and making it into another big comfortable bed when the 'plopping' gets too much or we have more visitors.

Cheers
Chris Flack
Hemera SM031

 

On 23-02-2015 01:52, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 
 

As some of you know, I was in the furniture manufacturing business for many years. This is something I know a little about.

If I were reupholstering the salon and did not want to use the polyester microfiber fabric that Amel used in SMs, my next choice would be Ultraleather brand urethane coated fabric. This looks like and feels like leather. It is as porous  and breathable as leather. They produce this urethane in 54" and 2m wide rolls and sell cut orders by the yard or meter through fabric distributors and designers in the EU & USA. I would pick the smoother grain (embossing). Google for more.

I have photos of a SM which was reupholstered with Ultraleather. It is beautiful. A German gal in France did the job. She also used new foam and a layer of memory foam. She also used double-needle stiching for extra detail and added strength.

Let me know if you want more details and or photos.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 


Posted by: Chris Flack <chris@...>
Reply via web post Reply to sender Reply to group Start a New Topic Messages in this topic (21)


Re: [Amel Yacht Owners] Maramu blisters

Bob <bob.sarff@...>
 

Thanks Chris......



On Feb 24, 2015, at 4:49 PM, Chris Smither yachtakwaaba@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hi
On my Santorin 27  1990 ,a prospective buyer popped a blister! ( Without my permission!) he claimed it was osmosis. The hull has since been treated.
Gurus cleverer than me have said you need to test the liquid in the bubble to confirm.
Since then I have found a good article about osmosis..will try to send it to you.
Akwaaba complete with bottom job, new engine and batteries is for sale  in Phuket.
Get a second opinion on the bubbles.
Good luck 
Chris Smither


On 24 Feb 2015, at 10:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Bob,

It could be triue, but I know for a fact that there are some certified crooks in the painting business in NZ.

What is the name of the guy who told you this, and the name of the business. Where is the business located.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 8:39 PM, "bob.sarff@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  


My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.


Thanks for any input you can furnish.


Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Maramu blisters

Bob <bob.sarff@...>
 

Interesting.....I hadn't thought of this at all.  I will definitely look into it.

Bob



On Feb 24, 2015, at 5:02 PM, Yahoo! Mail sammie.whammie@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Buy a peeler to remove the gel coat for about $500.00 and peel it in two days and apply epoxy in one day. Just need a yard that lets you do your own work. Two kinds of peelers. One thousand dollars and other made for house paint but sold for boat work. Need a vacumn that connects to peller or shaver. One types Is like a planner blade the other is like a angle grinder but both use carbide and diamond cutters. Very easy compared to sanding and grinding. Not as much flying particles and effort. Process is peel, epoxy then barrier coat and finally antifouling paint. Sanding only after peeling to smooth surface, then apply each coat before their too dry so that each coat burns in or much sanding. Look how it is done on YouTube, you will be surprised how each compared to grinding. It also makes very little free floating particles and it is mostly in the vacumn.


Sent from Yahoo Mail for iPad

At Feb 23, 2015, 9:39:04 PM, bob.sarff@... [amelyachtowners]amelyachtowners@...'> wrote:

I have some small blisters since I purchased me 1985 Maramu 7 years ago. I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied. The cost is estimated to be $25,000 nzd.


My question to other Maramu owners is, is this a common problem with older Maramu's? Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.


Thanks for any input you can furnish.


Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Maramu blisters

Bob <bob.sarff@...>
 

Thanks again.  The liquid that came out did seem very caustic.

Bob



On Feb 24, 2015, at 5:25 PM, sailormon kimberlite@... [amelyachtowners] <amelyachtowners@...> wrote:

 

As a PS,

Wear goggles as the liquid in the blisters is quite caustic.

You might want to just grind a small hole in the blister and let it drain and then come back and sand it when it is dry.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 10:27 PM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Maramu blisters

 

 

Thanks Eric for your reply.  I'm thinking of doing the same thing but wanted others opinions.  Much appreciated.  I may wait until next season in NZ after another 6 months in the tropics.

 

Bob


On Feb 24, 2015, at 4:20 PM, sailormon kimberlite@... [amelyachtowners] <amelyachtowners@...> wrote:

 

My previous boat had about 400 blisters.

I ground each one down with a dremel tool .

I then waited a few weeks , as it was summer and filled all the holes with epoxy putty and faired the hull. I then put on 3 coats of Interprotect - Interlux InterProtect Epoxy Primer‎ . Then one coat of blue bottom paint and 2 coats of black. End of problem. When I saw blue paint I knew it was time to repaint. It was a simple job but tedious and time consuming.  I do not see the logic in removing all the gel coat from a boat if there is not a problem.

 

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 9:39 PM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Maramu blisters

 

 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  

 

My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.

 

Thanks for any input you can furnish.

 

Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Maramu blisters

Bob <bob.sarff@...>
 

I'm at the Norsand boat yard and so far have been very happy with their work.  The yard manager Peter is the one I've been talking with.  There are several boats here going through the process I've described.

Thanks for your comments.

Bob




On Feb 24, 2015, at 4:34 PM, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Bob,

It could be triue, but I know for a fact that there are some certified crooks in the painting business in NZ.

What is the name of the guy who told you this, and the name of the business. Where is the business located.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 8:39 PM, "bob.sarff@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  


My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.


Thanks for any input you can furnish.


Bob

S/V Chara

Hin 173


Banging main furler foil without a sail.

sailormon <kimberlite@...>
 

No one posted this problem but I always found it very annoying when I am having my main sail repaired. The foil bangs around in the mast.

To alleviate this noise I finally came up with a good solution.

 

I lower the swivel to the bottom and run the largest diameter line that will fit  into the swivel.

I then raise the swivel to the top of the mast and rotate the foil while standing as far from the mast as possible. The line wraps around the foil making a bumper sort of arrangement.

The more line you have the better the bumper.

It is then quite silent.

 

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 


Re: [Amel Yacht Owners] Interior Upholstery

Chris Flack
 

Bill,

I'll run that up the mast tonight and see how it flies  

Chris

 

 

On 24-02-2015 13:06, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,

You have not spent many nights on that SM. At some point, the flopping stopped bothering us...We don't even hear it. It is not worth tampering with the table...just my opinion.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:54 PM, "Chris Flack chris@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

 

Thanks Bill,

The bed was really for us to use when the 'plopping' at the stern became too much (Jennifer is a light sleeper) and also for more air BUT for 2400 euro might be a better proposition to get more of the upholstery done and new curtains (those concertina type)

I have asked Riza for a quote on the cockpit cushions and also for the space atop the aft cabin.

 

Cheers again
Chris

 

 

 

On 24-02-2015 12:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,

Thanks. 

I do not think that I would try to make the dining table collapsible for another berth. If you are in a situation where all of the bunks are full, two people can sleep comfortably in the cockpit...invest in cockpit cushions instead...you will be happier.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:21 PM, "Chris Flack chris@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

 

Yes Bill - you will not get the support under your thighs/knees will you? Yes, better to keep that bull nose.

Jennifer said to say that you and the others in the group have gone to an awful lot of trouble to guide us.

Cheers

Chris

 

 

On 24-02-2015 10:19, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris if you change the depth of that seat cushion, you will wind up with an uncomfortable seat.
 
Bill

On Mon, Feb 23, 2015 at 3:49 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Hi Bill,

I have sent these photos through to Jennifer to show her how smart it looks. It is definitely a great facelift and looks ultra-comfortable.

With the bull nose on the front of the seat, it may not work with my plan to turn the lowered dining table into a bed and will have to think about keeping that section flat. I also hadn't thought of doing the nav seat but it would be so much better if we did.

Thanks for the extra effort you are putting in to help us out.

 

Cheers
Chris Flack
Hemera SM031

 

 

 

On 24-02-2015 08:31, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,
 
Look closely at the photos. 
 
The seats and back style was changed with the "channel quilting" removed. The back also has an added interior zipper (like the seat does) which gives it that look of a pillow at the top of the back and a bull nose on the front of the seat...see photo "RF Back Detail" and "LF Seat Detail"
 
Also look at the very large circular back...it has been split into 3 pieces. Look at the photo labeled "LF Corner" and "RF Corner" which show the split. You can also see how the original seat was made by first removing the piece of foam from the backside of the seat cushion. Once removed, you will see an internal zipper which when opened reveals the bull nose piece of foam.
 
I would use UltraLeather Ivory also. Tomorrow I am going to visit their distributor in Houston, I will try to get a sample that I can mail to you.
 
Bill
BeBe

On Mon, Feb 23, 2015 at 2:51 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Thank you Bill,

I asked Riza to use the UltraLeather Ivory on our refit with the memory foam layer and to also make up a 2 section insert for the dining table when we drop it down to a bed. Getting really excited about the things we are doing and can't wait to get over there at the beginning of May.

 

Cheers
Chris Flack
HemeraSm031

 

 

On 24-02-2015 00:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris:
 

  Ultrafabrics Europe, Ltd

19 The Warren,
East Goscote,
Leicestershire, LE7 3XA
United Kingdom

Main Phone: +44.116.260.9625
Email: ufe@...

On Sun, Feb 22, 2015 at 10:08 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Bill, thanks you again.

This is very interesting and the Ivory does look good. Not too sure between the UltraLeather and the UltraLeather Pro.

I hope Riza is able to source it for me.

I hope your folk up there are starting to thaw out.

 

Cheers
Chris
Hemera SM031

 

 

On 23-02-2015 11:18, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,
 
Alcantara and Ultrasuede are two of the best known brands for a fabric that has a polyester fiber electrostatically glued to a base cloth. The result is a fabric that looks like a perfect leather suede. There are many qualities and prices. I am not sure which brand Amel used on the SM 2000.
 
Polyester fiber is easily cleaned with soap and water, but will also take alcohol type cleaners for tough grease stains. Polyurethane coated fabrics are harder to stain, will clean with soap and water and you need to test alcohol or petroleum-based cleaners need to be tested on Polyrethane, because they may dull the luster. 
 
If I were changing, I would probably use Ultraleather™ Color Ivory https://www.ultrafabricsllc.com/Site/Swatch/30/ 
<<>> Ultraleather™ Pro Color Swan https://www.ultrafabricsllc.com/Site/Swatch/597/
 
I will upload a few photos of the interior of SM ARAMIS...hopefully the owner will not mind. It is beautiful!
 
Bill
BeBe 387
 
 

On Sun, Feb 22, 2015 at 4:16 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Hi Bill,

I didn't know your past history but your advice is again, invaluable. 

Is the polyester microfiber fabric that Amel use the Alcantara? Does the Ultraleather clean up well from possible grease and stains?

Some photos and details of what you have described would be great thank you. The idea of the memory foam would add even greater comfort. We are also looking at turning the thinking table into a drop down and making it into another big comfortable bed when the 'plopping' gets too much or we have more visitors.

Cheers
Chris Flack
Hemera SM031

 

On 23-02-2015 01:52, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

As some of you know, I was in the furniture manufacturing business for many years. This is something I know a little about.

If I were reupholstering the salon and did not want to use the polyester microfiber fabric that Amel used in SMs, my next choice would be Ultraleather brand urethane coated fabric. This looks like and feels like leather. It is as porous  and breathable as leather. They produce this urethane in 54" and 2m wide rolls and sell cut orders by the yard or meter through fabric distributors and designers in the EU & USA. I would pick the smoother grain (embossing). Google for more.

I have photos of a SM which was reupholstered with Ultraleather. It is beautiful. A German gal in France did the job. She also used new foam and a layer of memory foam. She also used double-needle stiching for extra detail and added strength.

Let me know if you want more details and or photos.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

 

 

 
 

 

 
 

 

 
 

 

 
 
 
 
 


Re: [Amel Yacht Owners] Maramu blisters

sailormon <kimberlite@...>
 

As a PS,

Wear goggles as the liquid in the blisters is quite caustic.

You might want to just grind a small hole in the blister and let it drain and then come back and sand it when it is dry.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 10:27 PM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Maramu blisters

 

 

Thanks Eric for your reply.  I'm thinking of doing the same thing but wanted others opinions.  Much appreciated.  I may wait until next season in NZ after another 6 months in the tropics.

 

Bob


On Feb 24, 2015, at 4:20 PM, sailormon kimberlite@... [amelyachtowners] <amelyachtowners@...> wrote:

 

My previous boat had about 400 blisters.

I ground each one down with a dremel tool .

I then waited a few weeks , as it was summer and filled all the holes with epoxy putty and faired the hull. I then put on 3 coats of Interprotect - Interlux InterProtect Epoxy Primer‎ . Then one coat of blue bottom paint and 2 coats of black. End of problem. When I saw blue paint I knew it was time to repaint. It was a simple job but tedious and time consuming.  I do not see the logic in removing all the gel coat from a boat if there is not a problem.

 

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 9:39 PM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Maramu blisters

 

 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  

 

My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.

 

Thanks for any input you can furnish.

 

Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Maramu blisters

Stephen Hancock
 

Buy a peeler to remove the gel coat for about $500.00 and peel it in two days and apply epoxy in one day. Just need a yard that lets you do your own work. Two kinds of peelers. One thousand dollars and other made for house paint but sold for boat work. Need a vacumn that connects to peller or shaver. One types Is like a planner blade the other is like a angle grinder but both use carbide and diamond cutters. Very easy compared to sanding and grinding. Not as much flying particles and effort. Process is peel, epoxy then barrier coat and finally antifouling paint. Sanding only after peeling to smooth surface, then apply each coat before their too dry so that each coat burns in or much sanding. Look how it is done on YouTube, you will be surprised how each compared to grinding. It also makes very little free floating particles and it is mostly in the vacumn.


Sent from Yahoo Mail for iPad

At Feb 23, 2015, 9:39:04 PM, bob.sarff@... [amelyachtowners]<'amelyachtowners@...'> wrote:

I have some small blisters since I purchased me 1985 Maramu 7 years ago. I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied. The cost is estimated to be $25,000 nzd.


My question to other Maramu owners is, is this a common problem with older Maramu's? Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.


Thanks for any input you can furnish.


Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Maramu blisters

Chris Smither <yachtakwaaba@...>
 

Hi
On my Santorin 27  1990 ,a prospective buyer popped a blister! ( Without my permission!) he claimed it was osmosis. The hull has since been treated.
Gurus cleverer than me have said you need to test the liquid in the bubble to confirm.
Since then I have found a good article about osmosis..will try to send it to you.
Akwaaba complete with bottom job, new engine and batteries is for sale  in Phuket.
Get a second opinion on the bubbles.
Good luck 
Chris Smither


On 24 Feb 2015, at 10:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Bob,

It could be triue, but I know for a fact that there are some certified crooks in the painting business in NZ.

What is the name of the guy who told you this, and the name of the business. Where is the business located.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 8:39 PM, "bob.sarff@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  


My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.


Thanks for any input you can furnish.


Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Maramu blisters

Bill & Judy Rouse <yahoogroups@...>
 

Bob,

It could be triue, but I know for a fact that there are some certified crooks in the painting business in NZ.

What is the name of the guy who told you this, and the name of the business. Where is the business located.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 8:39 PM, "bob.sarff@... [amelyachtowners]" <amelyachtowners@...> wrote:

 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  


My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.


Thanks for any input you can furnish.


Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Maramu blisters

Bob <bob.sarff@...>
 

Thanks Eric for your reply.  I'm thinking of doing the same thing but wanted others opinions.  Much appreciated.  I may wait until next season in NZ after another 6 months in the tropics.

Bob



On Feb 24, 2015, at 4:20 PM, sailormon kimberlite@... [amelyachtowners] <amelyachtowners@...> wrote:

 

My previous boat had about 400 blisters.

I ground each one down with a dremel tool .

I then waited a few weeks , as it was summer and filled all the holes with epoxy putty and faired the hull. I then put on 3 coats of Interprotect - Interlux InterProtect Epoxy Primer . Then one coat of blue bottom paint and 2 coats of black. End of problem. When I saw blue paint I knew it was time to repaint. It was a simple job but tedious and time consuming.  I do not see the logic in removing all the gel coat from a boat if there is not a problem.

 

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 9:39 PM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Maramu blisters

 

 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  

 

My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.

 

Thanks for any input you can furnish.

 

Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Maramu blisters

sailormon <kimberlite@...>
 

My previous boat had about 400 blisters.

I ground each one down with a dremel tool .

I then waited a few weeks , as it was summer and filled all the holes with epoxy putty and faired the hull. I then put on 3 coats of Interprotect - Interlux InterProtect Epoxy Primer . Then one coat of blue bottom paint and 2 coats of black. End of problem. When I saw blue paint I knew it was time to repaint. It was a simple job but tedious and time consuming.  I do not see the logic in removing all the gel coat from a boat if there is not a problem.

 

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 9:39 PM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Maramu blisters

 

 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  

 

My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.

 

Thanks for any input you can furnish.

 

Bob

S/V Chara

Hin 173


Maramu blisters

bob.sarff@...
 

I have some small blisters since I purchased me 1985 Maramu 7 years ago.  I've always been told that they were small and just cosmetic.

This latest haul out in NZ I'm being told that I should have a complete osmosis repair and it could take 2 1/2-3 months for the hull dr dry out after grinding and before 3 coats of epoxy can be applied.  The cost is estimated to be $25,000 nzd.  


My question to other Maramu owners is, is this a common problem with older Maramu's?  Has anyone with a similar problem taken a different approach (like grinding the blisters individually yourself vs using a me jibe to skim off the entire chop layer of fiberglass.


Thanks for any input you can furnish.


Bob

S/V Chara

Hin 173


Re: [Amel Yacht Owners] Interior Upholstery

Bill & Judy Rouse <yahoogroups@...>
 

Chris,

You have not spent many nights on that SM. At some point, the flopping stopped bothering us...We don't even hear it. It is not worth tampering with the table...just my opinion.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:54 PM, "Chris Flack chris@... [amelyachtowners]" <amelyachtowners@...> wrote:

 

Thanks Bill,

The bed was really for us to use when the 'plopping' at the stern became too much (Jennifer is a light sleeper) and also for more air BUT for 2400 euro might be a better proposition to get more of the upholstery done and new curtains (those concertina type)

I have asked Riza for a quote on the cockpit cushions and also for the space atop the aft cabin.

 

Cheers again
Chris

 

 

 

On 24-02-2015 12:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,

Thanks. 

I do not think that I would try to make the dining table collapsible for another berth. If you are in a situation where all of the bunks are full, two people can sleep comfortably in the cockpit...invest in cockpit cushions instead...you will be happier.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:21 PM, "Chris Flack chris@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

 

Yes Bill - you will not get the support under your thighs/knees will you? Yes, better to keep that bull nose.

Jennifer said to say that you and the others in the group have gone to an awful lot of trouble to guide us.

Cheers

Chris

 

 

On 24-02-2015 10:19, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris if you change the depth of that seat cushion, you will wind up with an uncomfortable seat.
 
Bill

On Mon, Feb 23, 2015 at 3:49 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Hi Bill,

I have sent these photos through to Jennifer to show her how smart it looks. It is definitely a great facelift and looks ultra-comfortable.

With the bull nose on the front of the seat, it may not work with my plan to turn the lowered dining table into a bed and will have to think about keeping that section flat. I also hadn't thought of doing the nav seat but it would be so much better if we did.

Thanks for the extra effort you are putting in to help us out.

 

Cheers
Chris Flack
Hemera SM031

 

 

 

On 24-02-2015 08:31, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,
 
Look closely at the photos. 
 
The seats and back style was changed with the "channel quilting" removed. The back also has an added interior zipper (like the seat does) which gives it that look of a pillow at the top of the back and a bull nose on the front of the seat...see photo "RF Back Detail" and "LF Seat Detail"
 
Also look at the very large circular back...it has been split into 3 pieces. Look at the photo labeled "LF Corner" and "RF Corner" which show the split. You can also see how the original seat was made by first removing the piece of foam from the backside of the seat cushion. Once removed, you will see an internal zipper which when opened reveals the bull nose piece of foam.
 
I would use UltraLeather Ivory also. Tomorrow I am going to visit their distributor in Houston, I will try to get a sample that I can mail to you.
 
Bill
BeBe

On Mon, Feb 23, 2015 at 2:51 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Thank you Bill,

I asked Riza to use the UltraLeather Ivory on our refit with the memory foam layer and to also make up a 2 section insert for the dining table when we drop it down to a bed. Getting really excited about the things we are doing and can't wait to get over there at the beginning of May.

 

Cheers
Chris Flack
HemeraSm031

 

 

On 24-02-2015 00:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris:
 

  Ultrafabrics Europe, Ltd

19 The Warren,
East Goscote,
Leicestershire, LE7 3XA
United Kingdom

Main Phone: +44.116.260.9625
Email: ufe@...

On Sun, Feb 22, 2015 at 10:08 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Bill, thanks you again.

This is very interesting and the Ivory does look good. Not too sure between the UltraLeather and the UltraLeather Pro.

I hope Riza is able to source it for me.

I hope your folk up there are starting to thaw out.

 

Cheers
Chris
Hemera SM031

 

 

On 23-02-2015 11:18, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,
 
Alcantara and Ultrasuede are two of the best known brands for a fabric that has a polyester fiber electrostatically glued to a base cloth. The result is a fabric that looks like a perfect leather suede. There are many qualities and prices. I am not sure which brand Amel used on the SM 2000.
 
Polyester fiber is easily cleaned with soap and water, but will also take alcohol type cleaners for tough grease stains. Polyurethane coated fabrics are harder to stain, will clean with soap and water and you need to test alcohol or petroleum-based cleaners need to be tested on Polyrethane, because they may dull the luster. 
 
If I were changing, I would probably use Ultraleather™ Color Ivory https://www.ultrafabricsllc.com/Site/Swatch/30/ 
<<>> Ultraleather™ Pro Color Swan https://www.ultrafabricsllc.com/Site/Swatch/597/
 
I will upload a few photos of the interior of SM ARAMIS...hopefully the owner will not mind. It is beautiful!
 
Bill
BeBe 387
 
 

On Sun, Feb 22, 2015 at 4:16 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Hi Bill,

I didn't know your past history but your advice is again, invaluable. 

Is the polyester microfiber fabric that Amel use the Alcantara? Does the Ultraleather clean up well from possible grease and stains?

Some photos and details of what you have described would be great thank you. The idea of the memory foam would add even greater comfort. We are also looking at turning the thinking table into a drop down and making it into another big comfortable bed when the 'plopping' gets too much or we have more visitors.

Cheers
Chris Flack
Hemera SM031

 

On 23-02-2015 01:52, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

As some of you know, I was in the furniture manufacturing business for many years. This is something I know a little about.

If I were reupholstering the salon and did not want to use the polyester microfiber fabric that Amel used in SMs, my next choice would be Ultraleather brand urethane coated fabric. This looks like and feels like leather. It is as porous  and breathable as leather. They produce this urethane in 54" and 2m wide rolls and sell cut orders by the yard or meter through fabric distributors and designers in the EU & USA. I would pick the smoother grain (embossing). Google for more.

I have photos of a SM which was reupholstered with Ultraleather. It is beautiful. A German gal in France did the job. She also used new foam and a layer of memory foam. She also used double-needle stiching for extra detail and added strength.

Let me know if you want more details and or photos.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

 

 

 
 

 

 
 

 

 
 

 

 
 
 


Re: [Amel Yacht Owners] Interior Upholstery

Chris Flack
 

Thanks Bill,

The bed was really for us to use when the 'plopping' at the stern became too much (Jennifer is a light sleeper) and also for more air BUT for 2400 euro might be a better proposition to get more of the upholstery done and new curtains (those concertina type)

I have asked Riza for a quote on the cockpit cushions and also for the space atop the aft cabin.

 

Cheers again
Chris

 

 

 

On 24-02-2015 12:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,

Thanks. 

I do not think that I would try to make the dining table collapsible for another berth. If you are in a situation where all of the bunks are full, two people can sleep comfortably in the cockpit...invest in cockpit cushions instead...you will be happier.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:21 PM, "Chris Flack chris@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

 

Yes Bill - you will not get the support under your thighs/knees will you? Yes, better to keep that bull nose.

Jennifer said to say that you and the others in the group have gone to an awful lot of trouble to guide us.

Cheers

Chris

 

 

On 24-02-2015 10:19, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris if you change the depth of that seat cushion, you will wind up with an uncomfortable seat.
 
Bill

On Mon, Feb 23, 2015 at 3:49 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Hi Bill,

I have sent these photos through to Jennifer to show her how smart it looks. It is definitely a great facelift and looks ultra-comfortable.

With the bull nose on the front of the seat, it may not work with my plan to turn the lowered dining table into a bed and will have to think about keeping that section flat. I also hadn't thought of doing the nav seat but it would be so much better if we did.

Thanks for the extra effort you are putting in to help us out.

 

Cheers
Chris Flack
Hemera SM031

 

 

 

On 24-02-2015 08:31, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,
 
Look closely at the photos. 
 
The seats and back style was changed with the "channel quilting" removed. The back also has an added interior zipper (like the seat does) which gives it that look of a pillow at the top of the back and a bull nose on the front of the seat...see photo "RF Back Detail" and "LF Seat Detail"
 
Also look at the very large circular back...it has been split into 3 pieces. Look at the photo labeled "LF Corner" and "RF Corner" which show the split. You can also see how the original seat was made by first removing the piece of foam from the backside of the seat cushion. Once removed, you will see an internal zipper which when opened reveals the bull nose piece of foam.
 
I would use UltraLeather Ivory also. Tomorrow I am going to visit their distributor in Houston, I will try to get a sample that I can mail to you.
 
Bill
BeBe

On Mon, Feb 23, 2015 at 2:51 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Thank you Bill,

I asked Riza to use the UltraLeather Ivory on our refit with the memory foam layer and to also make up a 2 section insert for the dining table when we drop it down to a bed. Getting really excited about the things we are doing and can't wait to get over there at the beginning of May.

 

Cheers
Chris Flack
HemeraSm031

 

 

On 24-02-2015 00:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris:
 

  Ultrafabrics Europe, Ltd

19 The Warren,
East Goscote,
Leicestershire, LE7 3XA
United Kingdom

Main Phone: +44.116.260.9625
Email: ufe@...

On Sun, Feb 22, 2015 at 10:08 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Bill, thanks you again.

This is very interesting and the Ivory does look good. Not too sure between the UltraLeather and the UltraLeather Pro.

I hope Riza is able to source it for me.

I hope your folk up there are starting to thaw out.

 

Cheers
Chris
Hemera SM031

 

 

On 23-02-2015 11:18, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,
 
Alcantara and Ultrasuede are two of the best known brands for a fabric that has a polyester fiber electrostatically glued to a base cloth. The result is a fabric that looks like a perfect leather suede. There are many qualities and prices. I am not sure which brand Amel used on the SM 2000.
 
Polyester fiber is easily cleaned with soap and water, but will also take alcohol type cleaners for tough grease stains. Polyurethane coated fabrics are harder to stain, will clean with soap and water and you need to test alcohol or petroleum-based cleaners need to be tested on Polyrethane, because they may dull the luster. 
 
If I were changing, I would probably use Ultraleather™ Color Ivory https://www.ultrafabricsllc.com/Site/Swatch/30/ 
<<>> Ultraleather™ Pro Color Swan https://www.ultrafabricsllc.com/Site/Swatch/597/
 
I will upload a few photos of the interior of SM ARAMIS...hopefully the owner will not mind. It is beautiful!
 
Bill
BeBe 387
 
 

On Sun, Feb 22, 2015 at 4:16 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Hi Bill,

I didn't know your past history but your advice is again, invaluable. 

Is the polyester microfiber fabric that Amel use the Alcantara? Does the Ultraleather clean up well from possible grease and stains?

Some photos and details of what you have described would be great thank you. The idea of the memory foam would add even greater comfort. We are also looking at turning the thinking table into a drop down and making it into another big comfortable bed when the 'plopping' gets too much or we have more visitors.

Cheers
Chris Flack
Hemera SM031

 

On 23-02-2015 01:52, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

As some of you know, I was in the furniture manufacturing business for many years. This is something I know a little about.

If I were reupholstering the salon and did not want to use the polyester microfiber fabric that Amel used in SMs, my next choice would be Ultraleather brand urethane coated fabric. This looks like and feels like leather. It is as porous  and breathable as leather. They produce this urethane in 54" and 2m wide rolls and sell cut orders by the yard or meter through fabric distributors and designers in the EU & USA. I would pick the smoother grain (embossing). Google for more.

I have photos of a SM which was reupholstered with Ultraleather. It is beautiful. A German gal in France did the job. She also used new foam and a layer of memory foam. She also used double-needle stiching for extra detail and added strength.

Let me know if you want more details and or photos.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

 

 

 
 

 

 
 

 

 
 

 

 
 
 


Re: [Amel Yacht Owners] Interior Upholstery

Bill & Judy Rouse <yahoogroups@...>
 

Chris,

Thanks. 

I do not think that I would try to make the dining table collapsible for another berth. If you are in a situation where all of the bunks are full, two people can sleep comfortably in the cockpit...invest in cockpit cushions instead...you will be happier.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:21 PM, "Chris Flack chris@... [amelyachtowners]" <amelyachtowners@...> wrote:

 

Yes Bill - you will not get the support under your thighs/knees will you? Yes, better to keep that bull nose.

Jennifer said to say that you and the others in the group have gone to an awful lot of trouble to guide us.

Cheers

Chris

 

 

On 24-02-2015 10:19, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris if you change the depth of that seat cushion, you will wind up with an uncomfortable seat.
 
Bill

On Mon, Feb 23, 2015 at 3:49 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Hi Bill,

I have sent these photos through to Jennifer to show her how smart it looks. It is definitely a great facelift and looks ultra-comfortable.

With the bull nose on the front of the seat, it may not work with my plan to turn the lowered dining table into a bed and will have to think about keeping that section flat. I also hadn't thought of doing the nav seat but it would be so much better if we did.

Thanks for the extra effort you are putting in to help us out.

 

Cheers
Chris Flack
Hemera SM031

 

 

 

On 24-02-2015 08:31, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,
 
Look closely at the photos. 
 
The seats and back style was changed with the "channel quilting" removed. The back also has an added interior zipper (like the seat does) which gives it that look of a pillow at the top of the back and a bull nose on the front of the seat...see photo "RF Back Detail" and "LF Seat Detail"
 
Also look at the very large circular back...it has been split into 3 pieces. Look at the photo labeled "LF Corner" and "RF Corner" which show the split. You can also see how the original seat was made by first removing the piece of foam from the backside of the seat cushion. Once removed, you will see an internal zipper which when opened reveals the bull nose piece of foam.
 
I would use UltraLeather Ivory also. Tomorrow I am going to visit their distributor in Houston, I will try to get a sample that I can mail to you.
 
Bill
BeBe

On Mon, Feb 23, 2015 at 2:51 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Thank you Bill,

I asked Riza to use the UltraLeather Ivory on our refit with the memory foam layer and to also make up a 2 section insert for the dining table when we drop it down to a bed. Getting really excited about the things we are doing and can't wait to get over there at the beginning of May.

 

Cheers
Chris Flack
HemeraSm031

 

 

On 24-02-2015 00:34, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris:
 

  Ultrafabrics Europe, Ltd

19 The Warren,
East Goscote,
Leicestershire, LE7 3XA
United Kingdom

Main Phone: +44.116.260.9625
Email: ufe@...

On Sun, Feb 22, 2015 at 10:08 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Bill, thanks you again.

This is very interesting and the Ivory does look good. Not too sure between the UltraLeather and the UltraLeather Pro.

I hope Riza is able to source it for me.

I hope your folk up there are starting to thaw out.

 

Cheers
Chris
Hemera SM031

 

 

On 23-02-2015 11:18, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

Chris,
 
Alcantara and Ultrasuede are two of the best known brands for a fabric that has a polyester fiber electrostatically glued to a base cloth. The result is a fabric that looks like a perfect leather suede. There are many qualities and prices. I am not sure which brand Amel used on the SM 2000.
 
Polyester fiber is easily cleaned with soap and water, but will also take alcohol type cleaners for tough grease stains. Polyurethane coated fabrics are harder to stain, will clean with soap and water and you need to test alcohol or petroleum-based cleaners need to be tested on Polyrethane, because they may dull the luster. 
 
If I were changing, I would probably use Ultraleather™ Color Ivory https://www.ultrafabricsllc.com/Site/Swatch/30/ 
<<<OR>>> Ultraleather™ Pro Color Swan https://www.ultrafabricsllc.com/Site/Swatch/597/
 
I will upload a few photos of the interior of SM ARAMIS...hopefully the owner will not mind. It is beautiful!
 
Bill
BeBe 387
 
 

On Sun, Feb 22, 2015 at 4:16 PM, Chris Flack chris@... [amelyachtowners] <amelyachtowners@...> wrote:
 

 

Hi Bill,

I didn't know your past history but your advice is again, invaluable. 

Is the polyester microfiber fabric that Amel use the Alcantara? Does the Ultraleather clean up well from possible grease and stains?

Some photos and details of what you have described would be great thank you. The idea of the memory foam would add even greater comfort. We are also looking at turning the thinking table into a drop down and making it into another big comfortable bed when the 'plopping' gets too much or we have more visitors.

Cheers
Chris Flack
Hemera SM031

 

On 23-02-2015 01:52, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

 

 

As some of you know, I was in the furniture manufacturing business for many years. This is something I know a little about.

If I were reupholstering the salon and did not want to use the polyester microfiber fabric that Amel used in SMs, my next choice would be Ultraleather brand urethane coated fabric. This looks like and feels like leather. It is as porous  and breathable as leather. They produce this urethane in 54" and 2m wide rolls and sell cut orders by the yard or meter through fabric distributors and designers in the EU & USA. I would pick the smoother grain (embossing). Google for more.

I have photos of a SM which was reupholstered with Ultraleather. It is beautiful. A German gal in France did the job. She also used new foam and a layer of memory foam. She also used double-needle stiching for extra detail and added strength.

Let me know if you want more details and or photos.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

 

 

 
 

 

 
 

 

 
 

 

 


Re: [Amel Yacht Owners] solarpanels

sailormon <kimberlite@...>
 

Wow,

That is a cool device.

Thanks

Eric

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 8:29 PM
To: amelyachtowners@...
Subject: RE: [Amel Yacht Owners] solarpanels

 

 

Eric,

The Victron 75/50 will take up to 75volts +-5% and up to 50 amps. It automatically senses the voltage of the battery bank and the state of charge, then charges the batteries based on 1 of the 10 preset charging routines...example: AGM charging curve.

So you can place them in series.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:22 PM, "sailormon kimberlite@... [amelyachtowners]" <amelyachtowners@...> wrote:

 

Bill,

Being that these panels each put out 28 volts wouldn’t they be put in parallel?

Fair Winds

Eric

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 8:44 AM
To : amelyachtowners@...
Subject: Re: [Amel Yacht Owners] solarpanels

 

 

Peter,

 

You should have no problem. Be sure that you have the right MPPT controller. The Victron 75/50 would allow you to connect up to 3 of these in series before your battery bank.

 

Bill

BeBe

 

 

< p class="MsoNormal">On Mon, Feb 23, 2015 at 5:40 AM, mausi@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hello,

 

I am planning to add solar panels on the arch which will be installed soon. My neighbor has 2 panels left which are Conergy Power Plus 220. These panels are normaly used for the roof of a house. Each one delivers 28,82 V(max) with a current of 7,74 A(max).

 

Would it be possible to use these kind of panels on a boat?

 

Fair Winds,

Peter

 


Re: [Amel Yacht Owners] solarpanels

Bill & Judy Rouse <yahoogroups@...>
 

Eric,

The Victron 75/50 will take up to 75volts +-5% and up to 50 amps. It automatically senses the voltage of the battery bank and the state of charge, then charges the batteries based on 1 of the 10 preset charging routines...example: AGM charging curve.

So you can place them in series.

Bill Rouse
BeBe Amel 53 #387
sent from my tablet

On Feb 23, 2015 7:22 PM, "sailormon kimberlite@... [amelyachtowners]" <amelyachtowners@...> wrote:

 

Bill,

Being that these panels each put out 28 volts wouldn’t they be put in parallel?

Fair Winds

Eric

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 8:44 AM
To : amelyachtowners@...
Subject: Re: [Amel Yacht Owners] solarpanels

 

 

Peter,

 

You should have no problem. Be sure that you have the right MPPT controller. The Victron 75/50 would allow you to connect up to 3 of these in series before your battery bank.

 

Bill

BeBe

 

 

< p class="MsoNormal">On Mon, Feb 23, 2015 at 5:40 AM, mausi@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hello,

 

I am planning to add solar panels on the arch which will be installed soon. My neighbor has 2 panels left which are Conergy Power Plus 220. These panels are normaly used for the roof of a house. Each one delivers 28,82 V(max) with a current of 7,74 A(max).

 

Would it be possible to use these kind of panels on a boat?

 

Fair Winds,

Peter

 


Re: [Amel Yacht Owners] solarpanels

sailormon <kimberlite@...>
 

Bill,

Being that these panels each put out 28 volts wouldn’t they be put in parallel?

Fair Winds

Eric

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Monday, February 23, 2015 8:44 AM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] solarpanels

 

 

Peter,

 

You should have no problem. Be sure that you have the right MPPT controller. The Victron 75/50 would allow you to connect up to 3 of these in series before your battery bank.

 

Bill

BeBe

 

 

On Mon, Feb 23, 2015 at 5:40 AM, mausi@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hello,

 

I am planning to add solar panels on the arch which will be installed soon. My neighbor has 2 panels left which are Conergy Power Plus 220. These panels are normaly used for the roof of a house. Each one delivers 28,82 V(max) with a current of 7,74 A(max).

 

Would it be possible to use these kind of panels on a boat?

 

Fair Winds,

Peter