Date   

Bowthruster does not rise far enough on Super Maramu

Mark Pitt
 

A couple of days ago I did some work on the bow thruster that involved
partly removing the motor as well as changing the seals and the oil in
the bow thruster prop assembly. I have it all back together now but I
cannot get the whole thing to ascend far enough to put the safety pin
in place unless someone stands under the boat (it is on the hard) and
pushes up with some force. Before this maintenance, I could insert
the safety pin judge by pulling lightly on the cable. How can I adjust
things so that I can get the motor to rise a small amount more so that
I can insert the safety pin? There were two spongy seals on between
the prop assembly and the hull, so I replaced them with two new seals.
Could two seals be the source of the problem?

Mark Pitt
"Sabbatical III" ASM #419


Heat exchanger

ianjenkins1946 <ianjudyjenkins@hotmail.com>
 

Hi Vito, Following your example I have now had my heat exchanger cleaned. After 2000 hours needed it!Thanks for the tip. Ian


Re: [Amel Yacht Owners] Re: Engine change

Udo J. Reich <udo@...>
 

Dear Mr. Potter,

Thank you for the helpful information. The engine seems ok a t this point. I
definitely need new motor mounts and some seals.

The Max Prop settings are great. Thank you. Do you happen to know to much
rpm this engine should go up to under full forward power?



Udo J. Reich

ambiente european tile design

Direct 206. 388 1025

Fax 206. 388 1043



_____

From: Joel F. Potter [mailto:jfpottercys@att.net]
Sent: Thursday, April 27, 2006 1:15 PM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] Re: Engine change



Dear Mr. Reich,

Is your Perkins engine in need of a re-build? I have a very
low hour VOLVO TMD 22 engine which is actually a Perkins
Prima/M80 Turbo with green paint. When Caterpillar bought
Perkins, initially they stopped Perkins from retail
marketing and instead focused on supplying other
manufacturers. Volvo marketed the Prima/M80T for several
years.

Anyway, I have one in a warehouse that was removed from a
Super Maramu because of a recurrent rear oil pan seal
failure where oil would leak out slowly. This has been
fixed. I would be willing to sell it for a lot less than a
rebuild. It has less than 500 hours, can't remember exactly
but I have it written down on the engine.

The MAX PROP numbers follow:
560 m.m
22º
X =E XRAY – ECHO
Y = D YANKEE – DELTA

Consult your MAX PROP manual if this reads like Greek to
you.

Best regards,
Joel F. Potter
AMEL 54 "HOLLIS" Hull #14







_____

YAHOO! GROUPS LINKS



* Visit your group "amelyachtowners
<http://groups.yahoo.com/group/amelyachtowners> " on the web.

* To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@yahoogroups.com
<mailto:amelyachtowners-unsubscribe@yahoogroups.com?subject=Unsubscribe>

* Your use of Yahoo! Groups is subject to the Yahoo!
<http://docs.yahoo.com/info/terms/> Terms of Service.



_____



[Non-text portions of this message have been removed]


Re: Engine change

amelforme
 

Dear Mr. Reich,

Is your Perkins engine in need of a re-build? I have a very
low hour VOLVO TMD 22 engine which is actually a Perkins
Prima/M80 Turbo with green paint. When Caterpillar bought
Perkins, initially they stopped Perkins from retail
marketing and instead focused on supplying other
manufacturers. Volvo marketed the Prima/M80T for several
years.

Anyway, I have one in a warehouse that was removed from a
Super Maramu because of a recurrent rear oil pan seal
failure where oil would leak out slowly. This has been
fixed. I would be willing to sell it for a lot less than a
rebuild. It has less than 500 hours, can't remember exactly
but I have it written down on the engine.

The MAX PROP numbers follow:
560 m.m
22º
X =E XRAY – ECHO
Y = D YANKEE – DELTA

Consult your MAX PROP manual if this reads like Greek to
you.

Best regards,
Joel F. Potter
AMEL 54 "HOLLIS" Hull #14


[Non-text portions of this message have been removed]


Re: [Amel Yacht Owners] Re: engine change

Udo J. Reich <udo@...>
 

Thank you Richard. I'll check it out.



Udo J. Reich

ambiente european tile design

Direct 206. 388 1025

Fax 206. 388 1043



_____

From: closereach [mailto:closereach@yahoo.com]
Sent: Wednesday, April 26, 2006 6:04 PM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] Re: engine change



Udo,

I have a 1989 Super Maramu with perhaps the same model M80T Perkins.
I suggest you give Foley Engines up in Mass a call or email--they
have everything you'll need to get your Perkins and Hurth
transmission running smoothly. Phone is 508-753-2979 or email
info@foleyengines.com. Even if your Perkins wasn't taken care of
properly and needs an overhaul, that may be a better (and less
costly) way to proceed.

Richard
SM#5 Spice

--- In amelyachtowners@yahoogroups.com, "Udo J. Reich" <udo@...>
wrote:

We are the new owners of a SM built in 1991 with the 80 hp Perkins
Turbo and
a Maxprop. I have several questions.

Has anybody changed engines and switched to the 4JH3-HTE Yanmar
engine?

If we keep the Perkins, we need new motor mounts. Any idea where to
get
them?

Anybody who has the same set up with the Maxprop. What is your
cruising rpm
and your max rpm under power?

Does anybody with a max prop and the 80 hp Perkins know the setting
of the
pitch of the prop?

I'd appreciate any input.





Udo J. Reich

Cloud seven












_____

YAHOO! GROUPS LINKS



* Visit your group "amelyachtowners
<http://groups.yahoo.com/group/amelyachtowners> " on the web.

* To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@yahoogroups.com
<mailto:amelyachtowners-unsubscribe@yahoogroups.com?subject=Unsubscribe>

* Your use of Yahoo! Groups is subject to the Yahoo!
<http://docs.yahoo.com/info/terms/> Terms of Service.



_____


Re: engine change

Zanareva
 

Udo,

I have a 1989 Super Maramu with perhaps the same model M80T Perkins.
I suggest you give Foley Engines up in Mass a call or email--they
have everything you'll need to get your Perkins and Hurth
transmission running smoothly. Phone is 508-753-2979 or email
info@foleyengines.com. Even if your Perkins wasn't taken care of
properly and needs an overhaul, that may be a better (and less
costly) way to proceed.

Richard
SM#5 Spice

--- In amelyachtowners@yahoogroups.com, "Udo J. Reich" <udo@...>
wrote:

We are the new owners of a SM built in 1991 with the 80 hp Perkins
Turbo and
a Maxprop. I have several questions.

Has anybody changed engines and switched to the 4JH3-HTE Yanmar
engine?

If we keep the Perkins, we need new motor mounts. Any idea where to
get
them?

Anybody who has the same set up with the Maxprop. What is your
cruising rpm
and your max rpm under power?

Does anybody with a max prop and the 80 hp Perkins know the setting
of the
pitch of the prop?

I'd appreciate any input.





Udo J. Reich

Cloud seven





[Non-text portions of this message have been removed]


engine change

Udo J. Reich <udo@...>
 

We are the new owners of a SM built in 1991 with the 80 hp Perkins Turbo and
a Maxprop. I have several questions.

Has anybody changed engines and switched to the 4JH3-HTE Yanmar engine?

If we keep the Perkins, we need new motor mounts. Any idea where to get
them?

Anybody who has the same set up with the Maxprop. What is your cruising rpm
and your max rpm under power?

Does anybody with a max prop and the 80 hp Perkins know the setting of the
pitch of the prop?

I'd appreciate any input.





Udo J. Reich

Cloud seven


Painting deck stripes

John and Anne on Bali Hai <hollamby@...>
 

Put deck stripes in the search box and become a well read painter!!

Regards, John


Re: Maramu forestay removal

myersdon1 <myersdon@...>
 

I don't have experience with the Maramu, however I have removed the
forestay on our Super Maramu. There is a plastic spacer at the
bottom of the foil that must be removed before pulling the forestay
out. Once this is removed the forestay comes out with very little
force. I suspect that the setup on the Maramu is similar.

Don Myers
SM160 Harmonie

--- In amelyachtowners@yahoogroups.com, "coatsken" <goldendaze@...>
wrote:

I have removed the main to paint and re rig on 1985 Maramu hull #
192.
All is apart except I am having difficulty getting the forestay out
of
the furling tube. I have tied the base to a tree and have pulled
on the
eye (top end) with a come-a-long up to about 800 pounds or so, (my
guess) and nothing has moved. Thinking corrosion in the tube
blocking
the plastic (or nylon) spacers (the gadjets that keep the wire from
touching the inner tube wall) I have poured wd-40 and mineral
spirits
down the tube. Still it won't budge. Has anyone got some
experience
with this job. Maybe I am overlooking something simple
(or stupid). Need help as am afraid of hurting the furling tube and
compounding my problems.
We had hoped to sail to the Med this May/June, but will postpone
until
next year as my time estimates on getting the boat ready have proven
to be somewhat naive.

Thanks,
Ken Coats & Judy Golden
SV Golden Daze
Maramu #192


Re: [Amel Yacht Owners] Maramu forestay removal

john martin <symoondog@...>
 

Ken, I have no experience with the furler, but lots with frozen,rusted bolts and nuts. There is a product called 'Blaster' P B sold in auto supply stores. It's 10 to one better then wd40 or any thing else. Don't leave port without it!
John Moondog SM248


From: "coatsken" <goldendaze@uuplus.com>
Reply-To: amelyachtowners@yahoogroups.com
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] Maramu forestay removal
Date: Mon, 24 Apr 2006 12:58:56 -0000

I have removed the main to paint and re rig on 1985 Maramu hull # 192.
All is apart except I am having difficulty getting the forestay out of
the furling tube. I have tied the base to a tree and have pulled on the
eye (top end) with a come-a-long up to about 800 pounds or so, (my
guess) and nothing has moved. Thinking corrosion in the tube blocking
the plastic (or nylon) spacers (the gadjets that keep the wire from
touching the inner tube wall) I have poured wd-40 and mineral spirits
down the tube. Still it won't budge. Has anyone got some experience
with this job. Maybe I am overlooking something simple
(or stupid). Need help as am afraid of hurting the furling tube and
compounding my problems.
We had hoped to sail to the Med this May/June, but will postpone until
next year as my time estimates on getting the boat ready have proven
to be somewhat naive.

Thanks,
Ken Coats & Judy Golden
SV Golden Daze
Maramu #192


_________________________________________________________________
FREE pop-up blocking with the new MSN Toolbar get it now! http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/


Painting deck stripes

liebling207 <liebling207@...>
 

rbenven44

We would like to paint the deck strips on our Amel and saw the
pictures you had posted. Could you let us know what materials you
used. The stripes look GREAT!
James DeSalvo


Re: [Amel Yacht Owners] leak in clothes washer

asm283 <no_reply@...>
 

Thanks Eric

I figured Amel must have done something to make it easy. As usual
you are a lifesaver.

Vito

--- In amelyachtowners@yahoogroups.com, eric <kimberlite@...> wrote:

Vito,

If your washer is anything like mine, there are a few polished
bolts on the
sides of the washer cabinet.

By removing these few bolts the whole cabinet comes away from the
washer and
is very easy to move or remove.

Fair Winds,

Eric

Amel Super Maramu #376 Kimberlite





_____

From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of asm283
Sent: Tuesday, April 25, 2006 1:59 AM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] leak in clotheswasher



Hello everyone

I have a 2000 SM# 283 with Thomson washer/drier

I have notied a slight leak in my clothes washer drier. I believe
its
from the freshwater intake but I cant be sure.

Has anyone had a similar problem. If so how did you fix it.

Has anyone had to remove the clotheswasher. How is this done?

Thanks

Vito







SPONSORED LINKS


Sailing
<http://groups.yahoo.com/gads?
t=ms&k=Sailing&w1=Sailing&w2=Sailing+yacht&w3=
Amel&w4=Boating+sailing&c=4&s=63&.sig=PlhCW0zvsb13KReuHX3A-Q>

Sailing
<http://groups.yahoo.com/gads?
t=ms&k=Sailing+yacht&w1=Sailing&w2=Sailing+yac
ht&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=SzbkQjL-
eN7E93cbJzL0eQ> yacht

Amel
<http://groups.yahoo.com/gads?
t=ms&k=Amel&w1=Sailing&w2=Sailing+yacht&w3=Ame
l&w4=Boating+sailing&c=4&s=63&.sig=pKnE4krYP80ImoJWH3305w>


Boating
<http://groups.yahoo.com/gads?
t=ms&k=Boating+sailing&w1=Sailing&w2=Sailing+y
acht&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=-
PqrRug6_9dlpPCqNcYXvA>
sailing







_____

YAHOO! GROUPS LINKS



* Visit your group "amelyachtowners
<http://groups.yahoo.com/group/amelyachtowners> " on the web.

* To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@yahoogroups.com
<mailto:amelyachtowners-unsubscribe@yahoogroups.com?
subject=Unsubscribe>

* Your use of Yahoo! Groups is subject to the Yahoo!
<http://docs.yahoo.com/info/terms/> Terms of Service.



_____





Re: [Amel Yacht Owners] leak in clothes washer

eric freedman
 

Vito,

If your washer is anything like mine, there are a few polished bolts on the
sides of the washer cabinet.

By removing these few bolts the whole cabinet comes away from the washer and
is very easy to move or remove.

Fair Winds,

Eric

Amel Super Maramu #376 Kimberlite





_____

From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of asm283
Sent: Tuesday, April 25, 2006 1:59 AM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] leak in clotheswasher



Hello everyone

I have a 2000 SM# 283 with Thomson washer/drier

I have notied a slight leak in my clothes washer drier. I believe its
from the freshwater intake but I cant be sure.

Has anyone had a similar problem. If so how did you fix it.

Has anyone had to remove the clotheswasher. How is this done?

Thanks

Vito







SPONSORED LINKS


Sailing
<http://groups.yahoo.com/gads?t=ms&k=Sailing&w1=Sailing&w2=Sailing+yacht&w3=
Amel&w4=Boating+sailing&c=4&s=63&.sig=PlhCW0zvsb13KReuHX3A-Q>

Sailing
<http://groups.yahoo.com/gads?t=ms&k=Sailing+yacht&w1=Sailing&w2=Sailing+yac
ht&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=SzbkQjL-eN7E93cbJzL0eQ> yacht

Amel
<http://groups.yahoo.com/gads?t=ms&k=Amel&w1=Sailing&w2=Sailing+yacht&w3=Ame
l&w4=Boating+sailing&c=4&s=63&.sig=pKnE4krYP80ImoJWH3305w>


Boating
<http://groups.yahoo.com/gads?t=ms&k=Boating+sailing&w1=Sailing&w2=Sailing+y
acht&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=-PqrRug6_9dlpPCqNcYXvA>
sailing







_____

YAHOO! GROUPS LINKS



* Visit your group "amelyachtowners
<http://groups.yahoo.com/group/amelyachtowners> " on the web.

* To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@yahoogroups.com
<mailto:amelyachtowners-unsubscribe@yahoogroups.com?subject=Unsubscribe>

* Your use of Yahoo! Groups is subject to the Yahoo!
<http://docs.yahoo.com/info/terms/> Terms of Service.



_____


leak in clotheswasher

asm283 <no_reply@...>
 

Hello everyone

I have a 2000 SM# 283 with Thomson washer/drier

I have notied a slight leak in my clothes washer drier. I believe its
from the freshwater intake but I cant be sure.

Has anyone had a similar problem. If so how did you fix it.

Has anyone had to remove the clotheswasher. How is this done?

Thanks

Vito


Re: [Amel Yacht Owners] Re: Maramu - size of battery box?

Horst Pause <horst@...>
 

Thank you for that, this is of great help



Horst - Maramu 168



________________________________

From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of coatsken
Sent: 24 April 2006 14:15
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] Re: Maramu - size of battery box?



Battery box on Maramu hull 192 is:
Length from inside forward end to pipe block aft: 43.25"
Width: 13.5"
This is compressing the foam that is still in my battery box
on the engine room wall side.
I just changed from gel cells to 6v lead acid golf cart batteries
and am happy so far (about 1 year, live aboard). Maintenence is
minor and cost is far less. Have 6 115 AH for house bank.
Use 1 12v AGM (Lifeline) for engine and am also happy with it.
(about 3 years). Hangs on to its charge well when not used.






________________________________

YAHOO! GROUPS LINKS



* Visit your group "amelyachtowners
<http://groups.yahoo.com/group/amelyachtowners> " on the web.

* To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@yahoogroups.com
<mailto:amelyachtowners-unsubscribe@yahoogroups.com?subject=Unsubscribe>


* Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service <http://docs.yahoo.com/info/terms/> .



________________________________


Re: Maramu - size of battery box?

coatsken <goldendaze@...>
 

Battery box on Maramu hull 192 is:
Length from inside forward end to pipe block aft: 43.25"
Width: 13.5"
This is compressing the foam that is still in my battery box
on the engine room wall side.
I just changed from gel cells to 6v lead acid golf cart batteries
and am happy so far (about 1 year, live aboard). Maintenence is
minor and cost is far less. Have 6 115 AH for house bank.
Use 1 12v AGM (Lifeline) for engine and am also happy with it.
(about 3 years). Hangs on to its charge well when not used.


Maramu forestay removal

coatsken <goldendaze@...>
 

I have removed the main to paint and re rig on 1985 Maramu hull # 192.
All is apart except I am having difficulty getting the forestay out of
the furling tube. I have tied the base to a tree and have pulled on the
eye (top end) with a come-a-long up to about 800 pounds or so, (my
guess) and nothing has moved. Thinking corrosion in the tube blocking
the plastic (or nylon) spacers (the gadjets that keep the wire from
touching the inner tube wall) I have poured wd-40 and mineral spirits
down the tube. Still it won't budge. Has anyone got some experience
with this job. Maybe I am overlooking something simple
(or stupid). Need help as am afraid of hurting the furling tube and
compounding my problems.
We had hoped to sail to the Med this May/June, but will postpone until
next year as my time estimates on getting the boat ready have proven
to be somewhat naive.

Thanks,
Ken Coats & Judy Golden
SV Golden Daze
Maramu #192


Maramu - size of battery box?

Horst Pause <horst@...>
 

I need new batteries, but am away from the boat.



Can anyone please measure the battery box, length and width, - I don't
want to end up with having to make a new box!



Thank you



Horst - Maramu 168


Re: [Amel Yacht Owners] NAVIONIC NAVNET CHARTS WANTED

Luis I. Gonzalez de Vallejo <l_gonzalezvallejo@...>
 

I have available some Navionics charts, never used because I have change my Furuno by a Simrad, the charts cover the Mediterranean coasts from Turquey , Greece, Italy, Balearics, Spanish Mediterranean coasts, and Atlantic coasts from Holland to Canaries.
If you are interested ,I can give more details,
Regards,
Luis G. de Vallejo



---------------------------------

LLama Gratis a cualquier PC del Mundo.
Llamadas a fijos y móviles desde 1 céntimo por minuto.
http://es.voice.yahoo.com

[Non-text portions of this message have been removed]


race handicap

svcallisto369
 

For all you loony racers out there in cyberland, you will find a
Southern California PHRF handicap rating from 2004 posted in the file
section of this forum.
There is one error that I did not correct, in that the rating factors
for a lead keel instead of a cast iron keel. I think that this is
probably because cast iron keels are very unusual in the US and there
was no way the calculation could be done.
I would agree that The SM is not much of a windward leeward boat, but
can do fairly well off the wind on random leg races especially if
there is a decent breeze.
The beer, however, is always cold.
Regards,
MDL