Date   

Re: C-Drive

tango708@...
 

Oliver,
Thanks again sorry that I was silent for a few days... we had the flex coupling repaired in Charleston, SC and were underway again.   The second day we made Beaufort and the following day departed Beaufort for Cape Charles.  However, about 4 hours after departing Beaufort the drive shaft between the new coupling and the c-drive broke.  Does anyone on the forum have any advise regarding replacing this shaft?  The prop turns freely and the engine and transmission seem to be working normally.  My C-Drive looks like it can be accessed from inside the engine room without removing the entire unit.  Does anyone have the spec's for the shaft?  Type of steel etc.  I know that it is 35 mm.  The replacement flex coupling is a Vetus Type 6, KO53 (i.e. 35mm)


Regards,
Will Stout,
Anni Bea True
SM180


Re: [Amel Yacht Owners] Repower

Eric Freedman
 

Kent ,

I get about 7+ knots at 2200 and about 9 at 3000.

I have the same engine with an autoprop.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Thursday, June 25, 2015 9:04 PM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Repower

 

 

My Volvo never got to maximum rpm until I re-propped, but after re-propping with a prop that was sized and pitched according to a prop shop in Norfolk, it did 7.5 kts at 2800rpm on flat water.  With my 110 Yanmar it does 8.3 kts at 3000rpm on flat water.  Not really significant since I don't run it that hard when motoring or motor sailing while cruising.  At 2200 rpm it pushes the boat at about 6 kts.

Kent

SM243

Kristy


On Jun 25, 2015, at 6:44 PM, 'hanspeter.baettig@...' hanspeter.baettig@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Question to all SM owners

Whats the different between 80 hp and 110 hp

Max Speed for SM is ca 8.5 kn

Independent how much power, the power on the Prop is Important 

I have this speed with clean  boat/Propeller with the Perkins 80 hp Turbo (1990, 3000 h)

Hanspeter

SM 16 Tamango 2

Göcek, Tutkey

Von meinem iPhone gesendet


Am 25.06.2015 um 18:18 schrieb "Germain Jean-Pierre jgermain@... [amelyachtowners]" <amelyachtowners@...>:

 

Wise choice Steve..

 

JPG




On 25 Jun 2015, at 17:00, flyboyscd@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Thanks for the info Chris. It looks like 80 hp is the way to go on our older boats due to the Cdrive issues.

Regards,
Steve and Liz
Aloha SM72


Re: [Amel Yacht Owners] Bottom Paint Warning

Bill & Judy Rouse <yahoogroups@...>
 

I am convinced that Micron66 is the best antifouling for the tropics. My conviction is rooted in using it for many years, renewing it every two years and first-hand comparisons I have made with antifouling others have used. That said, I may be biased, because Micron66 was my choice. And, it generally costs more than others.

As mentioned in this thread, International Paint warns that taking Micron66 into fresh water will harm its effectiveness. I assume that is why International produced Micron77, which is effective in fresh and saltwater. Unfortunately, the EPA will not approve Micron77. I believe that in the last 6 years the EPA has blocked all new antifouling applications. Therefore, Micron77 is only available outside the influence of the EPA (some countries chose to follow the EPA). We applied Micron77 in Malta, and it is available in all of the EU.

I guess if the EPA inspects our hull, the antifouling will morph to Micron66.

Kent, I am not sure, but if that tin-based paint was a hard paint, but, if it is, the primer International makes for Micron66 may work for you. If I were you, I would talk directly to one of the International Distributors, or directly with International.

One more remark: I have found that the less costly Micron Extra is not as effective as the more costly Micron66 & Mucron77, but Micron Extra may be OK for non-tropical use.

Bill Rouse
BeBe Amel 53 #387
Sent from my tablet
+39 333 121 8115 Italy Mobile
+1832-380-4970 USA Voice Mail

On Jul 4, 2015 10:20 PM, "Vladimir Sonsev sonsev52@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

Good information.
Thanks.

Vladimir
"Life is Good"
SM 345

On Jul 4, 2015 8:16 AM, "Kent Robertson karkauai@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

The Kristy saga continues:

3 1/2 yrs ago I had the bottom painted in Trinidad. Sea Hawk's Island 44 was recommended. After taking the old paint down to gelcoat (it had 12 years of paint), a barrier coat was applied, then 2 coats of this tin-based paint (which is banned in the U.S. by the EPA). Great paint...lasted 3 + years and probably could have gone another 6 months.

I called a SeaHawk distributor and asked what they recommended since I couldn't buy it in the U.S., and he recommended their Island77. No mention of barrier coat or anything else.
I hauled out in Fernandina Beach, FL and had the bottom cleaned and lightly sanded, then 2 coats of Island77 applied. Then I discovered the prop shaft damage and the boat stayed on the hard for a year. Before launching I had another coat of Island 77 applied.

After sailing for only 6 weeks, I discovered the zincs were half gone already. I decided to haul out again so I could look at the prop shaft and have the topsides polished. All that new paint was GONE!

I called SeaHawk again, and this time they said "Nothing sticks to that tin-based paint." They recommended sanding it all down to gelcoat again.

If that isn't bad enough, the EPA requires that it be removed in an enclosed space, doesn't allow sandblasting it, only chemical stripper and sanding the rest with vacuum collection of dust, and disposal in a lined landfill. $10K just for paint removal! Plus a new barrier coat and new paint.

Moral of this story is 'Don't be lured into using banned paint unless you are going to be somewhere that you can buy it again when it's time to repaint." Apparently many places where you could buy it 3 years ago have now quit selling it.

I sure do seem to learn the hard way, don't I?

Steady as she goes.
Kent
SM243
Kristy


Re: [Amel Yacht Owners] Bottom Paint Warning

karkauai
 

Thanks Steve.  Happy Fourth!  Hope your new Yanmar shows up on Monday!
Kent



From: "Steve Davis flyboyscd@... [amelyachtowners]"
To: "amelyachtowners@..."
Sent: Saturday, July 4, 2015 11:56 AM
Subject: Re: [Amel Yacht Owners] Bottom Paint Warning

 
Hey Kent,

Sorry about the latest issues, but you have got to be over the hump soon, as you have more than paid your due to the Gods of Chaos. We are still hauled in St Augustine, and hoping our new motor shows by mid next week. 

When we hauled at Fernandina in November, we put 2 coats of Sea Hawk Biocop TF. We have mostly been sitting at the dock in the marina, and we are in a notoriously high growth area up the San Sebastian river, and had not moved the boat until about 10 days ago when we went sailing. When we hauled after the sail, our bottom was almost completely clean. The Biocop TF is a hard ablative paint and I decided to give it a try after discussing it with Sea Hawk. I had originally intended to use the Micron 66, but decided not to when I learned that fresh water kills the paint. The Biocop TF is good in fresh or salt water, and so far, I'm impressed with its performance. I also prefer ablative paints, as it helps to prevent excessive build up over the years, followed by expensive paint removal. Not that it matters, but we painted our bottom red, and I kind of like the look. 

Hang in there, and you will be enjoying being on the water again soon. 

Steve and Liz
Aloha SM72




On Jul 4, 2015, at 08:13, Kent Robertson karkauai@... [amelyachtowners] <amelyachtowners@...> wrote:

 
The Kristy saga continues:

3 1/2 yrs ago I had the bottom painted in Trinidad. Sea Hawk's Island 44 was recommended. After taking the old paint down to gelcoat (it had 12 years of paint), a barrier coat was applied, then 2 coats of this tin-based paint (which is banned in the U.S. by the EPA). Great paint...lasted 3 + years and probably could have gone another 6 months.

I called a SeaHawk distributor and asked what they recommended since I couldn't buy it in the U.S., and he recommended their Island77. No mention of barrier coat or anything else.
I hauled out in Fernandina Beach, FL and had the bottom cleaned and lightly sanded, then 2 coats of Island77 applied. Then I discovered the prop shaft damage and the boat stayed on the hard for a year. Before launching I had another coat of Island 77 applied.

After sailing for only 6 weeks, I discovered the zincs were half gone already. I decided to haul out again so I could look at the prop shaft and have the topsides polished. All that new paint was GONE!

I called SeaHawk again, and this time they said "Nothing sticks to that tin-based paint." They recommended sanding it all down to gelcoat again.

If that isn't bad enough, the EPA requires that it be removed in an enclosed space, doesn't allow sandblasting it, only chemical stripper and sanding the rest with vacuum collection of dust, and disposal in a lined landfill. $10K just for paint removal! Plus a new barrier coat and new paint.

Moral of this story is 'Don't be lured into using banned paint unless you are going to be somewhere that you can buy it again when it's time to repaint." Apparently many places where you could buy it 3 years ago have now quit selling it.

I sure do seem to learn the hard way, don't I?

Steady as she goes.
Kent
SM243
Kristy




Re: [Amel Yacht Owners] Bottom Paint Warning

Stephen Davis
 

Hey Kent,

Sorry about the latest issues, but you have got to be over the hump soon, as you have more than paid your due to the Gods of Chaos. We are still hauled in St Augustine, and hoping our new motor shows by mid next week. 

When we hauled at Fernandina in November, we put 2 coats of Sea Hawk Biocop TF. We have mostly been sitting at the dock in the marina, and we are in a notoriously high growth area up the San Sebastian river, and had not moved the boat until about 10 days ago when we went sailing. When we hauled after the sail, our bottom was almost completely clean. The Biocop TF is a hard ablative paint and I decided to give it a try after discussing it with Sea Hawk. I had originally intended to use the Micron 66, but decided not to when I learned that fresh water kills the paint. The Biocop TF is good in fresh or salt water, and so far, I'm impressed with its performance. I also prefer ablative paints, as it helps to prevent excessive build up over the years, followed by expensive paint removal. Not that it matters, but we painted our bottom red, and I kind of like the look. 

Hang in there, and you will be enjoying being on the water again soon. 

Steve and Liz
Aloha SM72


On Jul 4, 2015, at 08:13, Kent Robertson karkauai@... [amelyachtowners] <amelyachtowners@...> wrote:

 

The Kristy saga continues:

3 1/2 yrs ago I had the bottom painted in Trinidad. Sea Hawk's Island 44 was recommended. After taking the old paint down to gelcoat (it had 12 years of paint), a barrier coat was applied, then 2 coats of this tin-based paint (which is banned in the U.S. by the EPA). Great paint...lasted 3 + years and probably could have gone another 6 months.

I called a SeaHawk distributor and asked what they recommended since I couldn't buy it in the U.S., and he recommended their Island77. No mention of barrier coat or anything else.
I hauled out in Fernandina Beach, FL and had the bottom cleaned and lightly sanded, then 2 coats of Island77 applied. Then I discovered the prop shaft damage and the boat stayed on the hard for a year. Before launching I had another coat of Island 77 applied.

After sailing for only 6 weeks, I discovered the zincs were half gone already. I decided to haul out again so I could look at the prop shaft and have the topsides polished. All that new paint was GONE!

I called SeaHawk again, and this time they said "Nothing sticks to that tin-based paint." They recommended sanding it all down to gelcoat again.

If that isn't bad enough, the EPA requires that it be removed in an enclosed space, doesn't allow sandblasting it, only chemical stripper and sanding the rest with vacuum collection of dust, and disposal in a lined landfill. $10K just for paint removal! Plus a new barrier coat and new paint.

Moral of this story is 'Don't be lured into using banned paint unless you are going to be somewhere that you can buy it again when it's time to repaint." Apparently many places where you could buy it 3 years ago have now quit selling it.

I sure do seem to learn the hard way, don't I?

Steady as she goes.
Kent
SM243
Kristy


Re: [Amel Yacht Owners] Re: Bottom Paint Warning

karkauai
 

Thanks Bill!  Olivier, can you confirm what Bill says about not needing a barrier coat if the hull is sanded down to gelcoat?  I guess if the sanding went through the gelcoat that area would need to have the barrier?

Happy 4th of July, everyone.  May the Fouth be with you! 🇺🇸🇺🇸💥💥🇺🇸🇺🇸


On Jul 4, 2015, at 11:11 AM, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Kent,

You will also be pleased (maybe not) to know that Amel does not use a barrier coat because on an Amel it is not necessary (true since sometime in the 80's). There is a proprietary anti-osmotic layer beneath the gellcoat on your Amel.

I might also add that I have very good round-the-world experience with International Micron66 and Micron77. I repaint every 2 years. 77 is not sold in the US...EPA approval lacking on any new product for the last 6-7 years. I did have a problem in New Zealand with a crook who thinned the Micron66, but International took care of that issue.

Bill
BeBe



On Sat, Jul 4, 2015 at 3:30 PM, seafeverofcuan@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Hi Kent,

            It is time to take a step back from that, this is supposed to be about enjoyment and living your dreams. If it was a day job you would change careers.
If it helps at all with negotiating the price, it took three guys twelve hours to wet strip Seafever earlier this year.
Interestingly,there was no evidence of a priming or tie coat by the factory on the hull which was very shiny, I lightly sanded it with wet and dry and applied two coats of Hempfel epoxy which I am very impressed with.
I really hope that you have finally turned a corner with this, a lesser man would have given up a long time ago.
Best regards,
Trevor
Seafever
SM 425 Redline
Mexico
For Sale 



Re: [Amel Yacht Owners] Re: Bottom Paint Warning

Bill & Judy Rouse <yahoogroups@...>
 

Kent,

You will also be pleased (maybe not) to know that Amel does not use a barrier coat because on an Amel it is not necessary (true since sometime in the 80's). There is a proprietary anti-osmotic layer beneath the gellcoat on your Amel.

I might also add that I have very good round-the-world experience with International Micron66 and Micron77. I repaint every 2 years. 77 is not sold in the US...EPA approval lacking on any new product for the last 6-7 years. I did have a problem in New Zealand with a crook who thinned the Micron66, but International took care of that issue.

Bill
BeBe



On Sat, Jul 4, 2015 at 3:30 PM, seafeverofcuan@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Hi Kent,

            It is time to take a step back from that, this is supposed to be about enjoyment and living your dreams. If it was a day job you would change careers.
If it helps at all with negotiating the price, it took three guys twelve hours to wet strip Seafever earlier this year.
Interestingly,there was no evidence of a priming or tie coat by the factory on the hull which was very shiny, I lightly sanded it with wet and dry and applied two coats of Hempfel epoxy which I am very impressed with.
I really hope that you have finally turned a corner with this, a lesser man would have given up a long time ago.
Best regards,
Trevor
Seafever
SM 425 Redline
Mexico
For Sale 



Re: [Amel Yacht Owners] Re: Bottom Paint Warning

karkauai
 

Thanks Trevor.  I guess you gotta love being on the water, eh?  Not gonna give up til the health or money give out.
Kent


On Jul 4, 2015, at 9:30 AM, seafeverofcuan@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hi Kent,

            It is time to take a step back from that, this is supposed to be about enjoyment and living your dreams. If it was a day job you would change careers.
If it helps at all with negotiating the price, it took three guys twelve hours to wet strip Seafever earlier this year.
Interestingly,there was no evidence of a priming or tie coat by the factory on the hull which was very shiny, I lightly sanded it with wet and dry and applied two coats of Hempfel epoxy which I am very impressed with.
I really hope that you have finally turned a corner with this, a lesser man would have given up a long time ago.
Best regards,
Trevor
Seafever
SM 425 Redline
Mexico
For Sale 


Re: Bottom Paint Warning

seafeverofcuan@...
 

Hi Kent,
            It is time to take a step back from that, this is supposed to be about enjoyment and living your dreams. If it was a day job you would change careers.
If it helps at all with negotiating the price, it took three guys twelve hours to wet strip Seafever earlier this year.
Interestingly,there was no evidence of a priming or tie coat by the factory on the hull which was very shiny, I lightly sanded it with wet and dry and applied two coats of Hempfel epoxy which I am very impressed with.
I really hope that you have finally turned a corner with this, a lesser man would have given up a long time ago.
Best regards,
Trevor
Seafever
SM 425 Redline
Mexico
For Sale 


Re: [Amel Yacht Owners] Bottom Paint Warning

VLADIMIR SONSEV
 

Good information.
Thanks.

Vladimir
"Life is Good"
SM 345

On Jul 4, 2015 8:16 AM, "Kent Robertson karkauai@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

The Kristy saga continues:

3 1/2 yrs ago I had the bottom painted in Trinidad. Sea Hawk's Island 44 was recommended. After taking the old paint down to gelcoat (it had 12 years of paint), a barrier coat was applied, then 2 coats of this tin-based paint (which is banned in the U.S. by the EPA). Great paint...lasted 3 + years and probably could have gone another 6 months.

I called a SeaHawk distributor and asked what they recommended since I couldn't buy it in the U.S., and he recommended their Island77. No mention of barrier coat or anything else.
I hauled out in Fernandina Beach, FL and had the bottom cleaned and lightly sanded, then 2 coats of Island77 applied. Then I discovered the prop shaft damage and the boat stayed on the hard for a year. Before launching I had another coat of Island 77 applied.

After sailing for only 6 weeks, I discovered the zincs were half gone already. I decided to haul out again so I could look at the prop shaft and have the topsides polished. All that new paint was GONE!

I called SeaHawk again, and this time they said "Nothing sticks to that tin-based paint." They recommended sanding it all down to gelcoat again.

If that isn't bad enough, the EPA requires that it be removed in an enclosed space, doesn't allow sandblasting it, only chemical stripper and sanding the rest with vacuum collection of dust, and disposal in a lined landfill. $10K just for paint removal! Plus a new barrier coat and new paint.

Moral of this story is 'Don't be lured into using banned paint unless you are going to be somewhere that you can buy it again when it's time to repaint." Apparently many places where you could buy it 3 years ago have now quit selling it.

I sure do seem to learn the hard way, don't I?

Steady as she goes.
Kent
SM243
Kristy


Bottom Paint Warning

karkauai
 

The Kristy saga continues:

3 1/2 yrs ago I had the bottom painted in Trinidad. Sea Hawk's Island 44 was recommended. After taking the old paint down to gelcoat (it had 12 years of paint), a barrier coat was applied, then 2 coats of this tin-based paint (which is banned in the U.S. by the EPA). Great paint...lasted 3 + years and probably could have gone another 6 months.

I called a SeaHawk distributor and asked what they recommended since I couldn't buy it in the U.S., and he recommended their Island77. No mention of barrier coat or anything else.
I hauled out in Fernandina Beach, FL and had the bottom cleaned and lightly sanded, then 2 coats of Island77 applied. Then I discovered the prop shaft damage and the boat stayed on the hard for a year. Before launching I had another coat of Island 77 applied.

After sailing for only 6 weeks, I discovered the zincs were half gone already. I decided to haul out again so I could look at the prop shaft and have the topsides polished. All that new paint was GONE!

I called SeaHawk again, and this time they said "Nothing sticks to that tin-based paint." They recommended sanding it all down to gelcoat again.

If that isn't bad enough, the EPA requires that it be removed in an enclosed space, doesn't allow sandblasting it, only chemical stripper and sanding the rest with vacuum collection of dust, and disposal in a lined landfill. $10K just for paint removal! Plus a new barrier coat and new paint.

Moral of this story is 'Don't be lured into using banned paint unless you are going to be somewhere that you can buy it again when it's time to repaint." Apparently many places where you could buy it 3 years ago have now quit selling it.

I sure do seem to learn the hard way, don't I?

Steady as she goes.
Kent
SM243
Kristy


Re: [Amel Yacht Owners] Re: Autohelm ST7000 will not leave Standby

Germain Jean-Pierre <jgermain@...>
 

Hi Bill,

Thank you.  I have bought some... See you sometime this summer.

JPG


On 3 Jul 2015, at 07:08, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Here are the International distributors for CorrosionX: http://corrosionx.com/international-distributors.html

You will find them in New Zealand, Australia, Caribbean, Europe, and in many other places around the world. It looks like someone in Turkey needs to become a distributor. JP, maybe you can recruit someone on your next trip.

Bill
BeBe

On Fri, Jul 3, 2015 at 4:26 AM, Chris Smither yachtakwaaba@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Hi
Had Akwaaba 's auto helm  checked and  instruments reinstalled recently. I had taken the computer to Tinley Electronics UK for service.
The local Thai engineer found the rudder angle sensor was faulty and another  sensor was easy to find.
Hope this helps
Chris Smither Santorin Sloop 027 (1990)


On 3 Jul 2015, at 08:07, Germain Jean-Pierre jgermain@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Good point for both of you.  I tried to source Corrosion X in EU... No luck.  However an aeronautical engineer friend recommended a good product.  ....


Jean-Pierre Germain 
SY ELEUTHERA, SM007


On 3 Jul 2015, at 02:04, divanz620@... [amelyachtowners] <amelyachtowners@...> wrote:

 

AND the other issue with WD40 is that it is hydrophilic...i.e.it attracts water...so as Bill says, everything may seem OK in the short term, but in the longer term the residual will attract water and cause corrosion and short circuits, the very thing you are trying to guard against.

Products like Corrosion X and Inox are hydrophibic...i.e. they repel water
WD40 has no place on my boat.
Cheers
Alan
Elyse SM437



Re: Autohelm ST7000 will not leave Standby

rossirossix4
 

CorrosionX is readily available in Europe (not sure about Ireland) on eBay.it and eBay.de   e..g.  http://www.ebay.it/itm/3x-400ml-CorrosionX-Hochleistungskorrosionsschutz-Schmierol-Rostschutz-Rostloser-/251695767685?pt=LH_DefaultDomain_77&hash=item3a9a3ca085

I purchased several cans of CorrosionX and CorrosionX HD, while we were in the Rome area, both were shipped from Germany and arrived within 3 days.  Prices were reasonably competitive with US.

Bob and Suzanne, Executive Teenagers
SM 429 KAIMI, Malta


Re: [Amel Yacht Owners] Re: Autohelm ST7000 will not leave Standby

seafeverofcuan@...
 

Bill,
      I first came across Corrosion X  in Trinidad and after years of thinking there was nothing better than WD40, I was really impressed. There were two grades as I remember.
Recently I discovered another product Boeshield -T9 which again has had good results, particuarily on plug in cables, chart plotter,radar,etc.
Unfortunately I have not been able to source either of these products in the UK when you do find them on line they can't be airfreighted to Ireland.
Best regards,
Trevor

Sea Fever of Cuan
SM425 Redline
For Sale
Mexico




Re: [Amel Yacht Owners] Re: Autohelm ST7000 will not leave Standby

Germain Jean-Pierre <jgermain@...>
 

Hi Gang,

Riza just told me he’s got lots…!

:-)


JPG



On 3 Jul 2015, at 07:08, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Here are the International distributors for CorrosionX: http://corrosionx.com/international-distributors.html

You will find them in New Zealand, Australia, Caribbean, Europe, and in many other places around the world. It looks like someone in Turkey needs to become a distributor. JP, maybe you can recruit someone on your next trip.

Bill
BeBe

On Fri, Jul 3, 2015 at 4:26 AM, Chris Smither yachtakwaaba@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Hi
Had Akwaaba 's auto helm  checked and  instruments reinstalled recently. I had taken the computer to Tinley Electronics UK for service.
The local Thai engineer found the rudder angle sensor was faulty and another  sensor was easy to find.
Hope this helps
Chris Smither Santorin Sloop 027 (1990)


On 3 Jul 2015, at 08:07, Germain Jean-Pierre jgermain@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Good point for both of you.  I tried to source Corrosion X in EU... No luck.  However an aeronautical engineer friend recommended a good product.  ....


Jean-Pierre Germain 
SY ELEUTHERA, SM007


On 3 Jul 2015, at 02:04, divanz620@... [amelyachtowners] <amelyachtowners@...> wrote:

 

AND the other issue with WD40 is that it is hydrophilic...i.e.it attracts water...so as Bill says, everything may seem OK in the short term, but in the longer term the residual will attract water and cause corrosion and short circuits, the very thing you are trying to guard against.

Products like Corrosion X and Inox are hydrophibic...i.e. they repel water
WD40 has no place on my boat.
Cheers
Alan
Elyse SM437






Posted by: "Bill & Judy Rouse" <yahoogroups@...>
Reply via web post Reply to sender Reply to group Start a New Topic Messages in this topic (12)


Re: [Amel Yacht Owners] Re: Autohelm ST7000 will not leave Standby

Bill & Judy Rouse <yahoogroups@...>
 

Here are the International distributors for CorrosionX: http://corrosionx.com/international-distributors.html

You will find them in New Zealand, Australia, Caribbean, Europe, and in many other places around the world. It looks like someone in Turkey needs to become a distributor. JP, maybe you can recruit someone on your next trip.

Bill
BeBe

On Fri, Jul 3, 2015 at 4:26 AM, Chris Smither yachtakwaaba@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Hi
Had Akwaaba 's auto helm  checked and  instruments reinstalled recently. I had taken the computer to Tinley Electronics UK for service.
The local Thai engineer found the rudder angle sensor was faulty and another  sensor was easy to find.
Hope this helps
Chris Smither Santorin Sloop 027 (1990)


On 3 Jul 2015, at 08:07, Germain Jean-Pierre jgermain@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Good point for both of you.  I tried to source Corrosion X in EU... No luck.  However an aeronautical engineer friend recommended a good product.  ....


Jean-Pierre Germain 
SY ELEUTHERA, SM007


On 3 Jul 2015, at 02:04, divanz620@... [amelyachtowners] <amelyachtowners@...> wrote:

 

AND the other issue with WD40 is that it is hydrophilic...i.e.it attracts water...so as Bill says, everything may seem OK in the short term, but in the longer term the residual will attract water and cause corrosion and short circuits, the very thing you are trying to guard against.

Products like Corrosion X and Inox are hydrophibic...i.e. they repel water
WD40 has no place on my boat.
Cheers
Alan
Elyse SM437



Re: [Amel Yacht Owners] Re: Autohelm ST7000 will not leave Standby

Chris Smither <yachtakwaaba@...>
 

Hi
Had Akwaaba 's auto helm  checked and  instruments reinstalled recently. I had taken the computer to Tinley Electronics UK for service.
The local Thai engineer found the rudder angle sensor was faulty and another  sensor was easy to find.
Hope this helps
Chris Smither Santorin Sloop 027 (1990)


On 3 Jul 2015, at 08:07, Germain Jean-Pierre jgermain@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Good point for both of you.  I tried to source Corrosion X in EU... No luck.  However an aeronautical engineer friend recommended a good product.  ....


Jean-Pierre Germain 
SY ELEUTHERA, SM007


On 3 Jul 2015, at 02:04, divanz620@... [amelyachtowners] <amelyachtowners@...> wrote:

 

AND the other issue with WD40 is that it is hydrophilic...i.e.it attracts water...so as Bill says, everything may seem OK in the short term, but in the longer term the residual will attract water and cause corrosion and short circuits, the very thing you are trying to guard against.

Products like Corrosion X and Inox are hydrophibic...i.e. they repel water
WD40 has no place on my boat.
Cheers
Alan
Elyse SM437


Re: [Amel Yacht Owners] Re: Autohelm ST7000 will not leave Standby

Germain Jean-Pierre <jgermain@...>
 

Good point for both of you.  I tried to source Corrosion X in EU... No luck.  However an aeronautical engineer friend recommended a good product.  ....


Jean-Pierre Germain 
SY ELEUTHERA, SM007


On 3 Jul 2015, at 02:04, divanz620@... [amelyachtowners] <amelyachtowners@...> wrote:

 

AND the other issue with WD40 is that it is hydrophilic...i.e.it attracts water...so as Bill says, everything may seem OK in the short term, but in the longer term the residual will attract water and cause corrosion and short circuits, the very thing you are trying to guard against.

Products like Corrosion X and Inox are hydrophibic...i.e. they repel water
WD40 has no place on my boat.
Cheers
Alan
Elyse SM437


Re: [Amel Yacht Owners] Re: Autohelm ST7000 will not leave Standby

Alan Leslie
 

AND the other issue with WD40 is that it is hydrophilic...i.e.it attracts water...so as Bill says, everything may seem OK in the short term, but in the longer term the residual will attract water and cause corrosion and short circuits, the very thing you are trying to guard against.
Products like Corrosion X and Inox are hydrophibic...i.e. they repel water
WD40 has no place on my boat.
Cheers
Alan
Elyse SM437


Re: Autohelm ST7000 will not leave Standby

Craig Briggs
 

HI Eamonn,

I have just replaced mine and have the old equipment available - please see private email I sent you.

Cheers,
Craig Briggs
SN#68 Sangaris, Ft Lauderdale


---In amelyachtowners@..., <eamonn.washington@...> wrote :

Hi

I have been following the forum for 6 months in preparation for buying our Super Maramu, #151.  Here is my first post, after our 2 week shakedown cruise!

The Autohelm ST7000 worked for an hour but since then failed to leave "Standby".  The rudder angle appears correctly.  Wires seem OK.  Also noteworthy to mention is that the original GPS display also fails to switch on, and it is connected to the SeaTalk bus.

I guess I should replace the GPS anyway.  I guess the ST7000 should be able to work without it (I can't figure out why it would need the GPS in the first place, Fluxgate and Rudder should be enough?).

I read all references in this forum to ST7000 but not being able to leave standby was never mentioned.  Any suggestions?

Eamonn
SM #151