Date   

Re: [Amel Yacht Owners] Re: Port and Door Holders...

Stephen Davis
 

Bill,

I'll check Budget Marine here in Sint Maarten on Monday, and let you know if they have them in stock. Budget stocks a lot of Goiot parts and most of the gaskets for ports and hatches. If not, I purchased several from the US Goiot distributor Rig Rite just a few months ago, and they should still be available from them. 

Steve Davis
Aloha SM72
Sint Maarten

On Mar 25, 2017, at 21:46, divanz620@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hello Bill,


I think all the SMs have them. Ours is 2004 and we have them.
If you find an elegant solution for replacement it would be handy to have on file for the future
Cheers
Alan
Elyse SM437


Re: [Amel Yacht Owners] Re: Port and Door Holders...

eric freedman
 

I bought a few 2 years ago at Budget Marine in St Maarten.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Sunday, March 26, 2017 3:00 AM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Re: Port and Door Holders...

 

 

BI'll

I bought a couple two years ago from Amel Martinique. They were in a Goiot plastic box.

Sorry I can't be more help than that. 

 

Ian 

Ocean Hobo SN96


Re: Port and Door Holders...

Ian Park
 

BI'll
I bought a couple two years ago from Amel Martinique. They were in a Goiot plastic box.
Sorry I can't be more help than that. 

Ian 
Ocean Hobo SN96


Re: Port and Door Holders...

Alan Leslie
 

Hello Bill,

I think all the SMs have them. Ours is 2004 and we have them.
If you find an elegant solution for replacement it would be handy to have on file for the future
Cheers
Alan
Elyse SM437


Port and Door Holders...

greatketch@...
 

On older SM's the portlights and some of the cabin doors were held open with black rubber "mushrooms".  After 20 years ours are starting to degrade.  I have never seen them available from Goiot (the original manufacturer) and Maude says Amel has none left in stock.


Anybody else already solve this problem and care to share?  I have a couple ideas of varying degrees of elegance but haven't finalized my thoughts yet...


Bill Kinney

SM#160 Harmonie

Ponce, PR

 


Re: Starboard electric genoa winch got lazy

amelliahona <no_reply@...>
 

My experience with this sort of intermittent or under-powered performance of DC (direct current) motors is that is virtually always dirty brushes & dirty commutator.  Generally easily fixed at minimal expense.  While I haven't done this service on my Lewmar 58 Jib Sheet winches, I know where they are mounted and that access may be limited to do that service in situ.  I fear you will need to remove the motor but once the motor is on the workbench it is a simple fix.  I did have virtually identical symptoms recently on my main sail furling motor, it took about an hour to fix but access was relatively easy.
Dirty commutators/worn brushes never fix themselves for long.

Let us know how it works out.  

Gary Silver  Amel SM 2K sv Liahona   Puerto Rico


Re: [Amel Yacht Owners] Unknown use for line on mizzen mast

eric freedman
 

The line can also be used with a bungee cord that came with the boat that holds the Passarell off of the dock when not in use.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Friday, March 24, 2017 8:07 PM
To: amelyachtowners@...; amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Unknown use for line on mizzen mast

 

 

Hi Alan,  there should be an open block attached at the end of the mizzen boom on the starbord side.  That line can be led around that block and used to lift your dinghy motor up onto the rail or over the rail and lowered into the aft lazarette.  

 

The line thru the block on the top of the mizzen is also for the mizzen balooner sail, if you have one.

 

Best regards, Dan Carlson

sv BeBe, SM#387

 

 

Hi folks,

On our SM there is a line that's tied to the rail that goes through a block just under the stbd side spreader on the mizzen mast.

Does anyone know what it is there for ? I can't work out what it would be used for.

We have another line that goes to a block at the top of the mast that we use for lifting the dinghy out of the water, but this shorter one beats me.

Cheers

Alan

Elyse SM437


Re: [Amel Yacht Owners] Unknown use for line on mizzen mast

Alan Leslie
 

Thanks Mark,

Ah ok, that could be it !
We have a Besenzoni hydraulic passarelle on the stern. We have the ladder / passarelle too, but no plank for it.
I think I may take this line and its block off as it doesn't seem to serve any purpose for us.
Cheers
Alan
Elyse SM437 


Re: [Amel Yacht Owners] Unknown use for line on mizzen mast

Alan Leslie
 

Thanks Don,

We have a line along the stbd side of the mizzen boom that we use for raising and lowering the outboard.

The mizzen ballooner has its own halyard through a block at the top of the mizzen mast.

Cheers
Alan 
Elyse SM437


Re: bug screens for small portholes

Duane Siegfri
 

Bill,

Thanks for posting Harmonie's solution to the screens, it's a great solution!

Duane


Re: [Amel Yacht Owners] Unknown use for line on mizzen mast

Mark Erdos
 

Alan,

 

We use this line to raise and lower the passerelle. The line attaches to the far end of the passerelle and can be used to raise or lower the from the cockpit when at dock. I’m not sure if this is the intended function of the line but this works well for us.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currenlty cruising – Turks and Caicos Islands

www.creampuff.us

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Friday, March 24, 2017 7:18 PM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Unknown use for line on mizzen mast

 

 

Hi folks,

On our SM there is a line that's tied to the rail that goes through a block just under the stbd side spreader on the mizzen mast.

Does anyone know what it is there for ? I can't work out what it would be used for.

We have another line that goes to a block at the top of the mast that we use for lifting the dinghy out of the water, but this shorter one beats me.

Cheers

Alan

Elyse SM437


Re: [Amel Yacht Owners] Unknown use for line on mizzen mast

Bill & Judy Rouse <yahoogroups@...>
 

Alan,

Use that halyard and the block at the end of the mizzen boom to raise your outboard engine to either the rail mount or inside the lazzerette. 


CW Bill Rouse
Admiral, Texas Navy
Commander Emeritus
Galveston Island
Sent using Google Fi
+1(832) 380-4970

   

On Mar 24, 2017 18:18, "divanz620@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

Hi folks,

On our SM there is a line that's tied to the rail that goes through a block just under the stbd side spreader on the mizzen mast.

Does anyone know what it is there for ? I can't work out what it would be used for.

We have another line that goes to a block at the top of the mast that we use for lifting the dinghy out of the water, but this shorter one beats me.

Cheers

Alan

Elyse SM437


Re: [Amel Yacht Owners] Unknown use for line on mizzen mast

Dan Carlson
 

Hi Alan,  there should be an open block attached at the end of the mizzen boom on the starbord side.  That line can be led around that block and used to lift your dinghy motor up onto the rail or over the rail and lowered into the aft lazarette.  

The line thru the block on the top of the mizzen is also for the mizzen balooner sail, if you have one.

Best regards, Dan Carlson
sv BeBe, SM#387



On Fri, Mar 24, 2017 at 7:18 PM, divanz620@... [amelyachtowners]
wrote:
 

Hi folks,

On our SM there is a line that's tied to the rail that goes through a block just under the stbd side spreader on the mizzen mast.

Does anyone know what it is there for ? I can't work out what it would be used for.

We have another line that goes to a block at the top of the mast that we use for lifting the dinghy out of the water, but this shorter one beats me.

Cheers

Alan

Elyse SM437


Unknown use for line on mizzen mast

Alan Leslie
 

Hi folks,

On our SM there is a line that's tied to the rail that goes through a block just under the stbd side spreader on the mizzen mast.

Does anyone know what it is there for ? I can't work out what it would be used for.

We have another line that goes to a block at the top of the mast that we use for lifting the dinghy out of the water, but this shorter one beats me.

Cheers

Alan

Elyse SM437


Re: [Amel Yacht Owners] Re: Starboard electric genoa winch got lazy

Porter McRoberts <portermcroberts@...>
 

Isn't that the truth!


On Mar 24, 2017, at 5:46 PM, greatketch@... [amelyachtowners] <amelyachtowners@...> wrote:

 


I do hate it when problems "fix" themselves.  

You can't reproduce it to troubleshoot, but you KNOW it's going to happen again.

Bill Kinney
SM160 Harmonie
Ponce, PR


---In amelyachtowners@..., wrote :


Hello Olivier and Bill,

The problem "fixed itself" a couple of days later, about two weeks ago.

Again, the problem lasted for about 3 days, humidity was low, it had not rained for weeks, we had not taken any waves, we had not stressed the winches, seas were nearly flat, winds were very modest.

On the Amp use scale, no load on winches:

Starboard winch ("was problem"): starts at 43 amp, then 42, then 41.9, 41.8, 41.7...

Port winch ("perfect"): starts at 48 amp, drops quickly to 42, then 41.9, 41.8, 41.7...

Port "sounds" stronger.  Both now pull the genoa just as well under load.  We sail almost every day.

Thanks again,


Peregrinus
SM2K #350 (2002)
At anchor, near Budva, Montenegro


Re: Starboard electric genoa winch got lazy

greatketch@...
 


I do hate it when problems "fix" themselves.  

You can't reproduce it to troubleshoot, but you KNOW it's going to happen again.

Bill Kinney
SM160 Harmonie
Ponce, PR


---In amelyachtowners@..., <svperegrinus@...> wrote :


Hello Olivier and Bill,

The problem "fixed itself" a couple of days later, about two weeks ago.

Again, the problem lasted for about 3 days, humidity was low, it had not rained for weeks, we had not taken any waves, we had not stressed the winches, seas were nearly flat, winds were very modest.

On the Amp use scale, no load on winches:

Starboard winch ("was problem"): starts at 43 amp, then 42, then 41.9, 41.8, 41.7...

Port winch ("perfect"): starts at 48 amp, drops quickly to 42, then 41.9, 41.8, 41.7...

Port "sounds" stronger.  Both now pull the genoa just as well under load.  We sail almost every day.

Thanks again,


Peregrinus
SM2K #350 (2002)
At anchor, near Budva, Montenegro


New file uploaded to amelyachtowners

amelyachtowners@...
 

Hello,


This email message is a notification to let you know that
a file has been uploaded to the Files area of the amelyachtowners
group.


File : /Harmonie Port Screens.pdf
Uploaded by : bill_9895 <greatketch@...>
Description : Description and photos of magnetically retained bug screen for Goiot opening ports.


You can access this file at the URL:
https://groups.yahoo.com/neo/groups/amelyachtowners/files/Harmonie%20Port%20Screens.pdf


To learn more about file sharing for your group, please visit:
https://help.yahoo.com/kb/index?page=content&y=PROD_GRPS&locale=en_US&id=SLN15398


Regards,


bill_9895 <greatketch@...>


Re: Starboard electric genoa winch got lazy

svperegrinus@yahoo.com
 


Hello Olivier and Bill,

The problem "fixed itself" a couple of days later, about two weeks ago.

Again, the problem lasted for about 3 days, humidity was low, it had not rained for weeks, we had not taken any waves, we had not stressed the winches, seas were nearly flat, winds were very modest.

On the Amp use scale, no load on winches:

Starboard winch ("was problem"): starts at 43 amp, then 42, then 41.9, 41.8, 41.7...

Port winch ("perfect"): starts at 48 amp, drops quickly to 42, then 41.9, 41.8, 41.7...

Port "sounds" stronger.  Both now pull the genoa just as well under load.  We sail almost every day.

Thanks again,


Peregrinus
SM2K #350 (2002)
At anchor, near Budva, Montenegro




---In amelyachtowners@..., <greatketch@...> wrote :

I think Olivier's suggestion for distinguishing between a motor problem and a control box problem is probably easier than mine. 

Bill Kinney
SM#160 Harmonie


---In amelyachtowners@..., <svperegrinus@...> wrote :

Thank you Bill,

Will test voltage tomorrow morning after we arrive.  Am terrified of attempting to remove the electric motor, as I remember Eric of Kimberlite mentioning his was very, very stuck due to not doing a periodic maintenance Lewmar told him is mandatory, yet which does not show on our Lewmar manual that came with the boats.  Of course this maintenance has never been done on Peregrinus!

Will post here on any follow-ups.

Cheerio,

SM2K N. 350
Underway, Venice to Ortona


Re: [Amel Yacht Owners] AC Installation in Florida

svperegrinus@yahoo.com
 

One caveat about Jeff Hawthorne.... yes, good and quality work... but when you tell him you want a Climma, he nay nays it and recommends an Airrrr.

Funny, Hawthorne used to show up on a list of Coastal Climate Control installers... before I worked with Jeff I actually called up Coastal and told them their Hawthorne reference was no good and they simply had no-one else!

I know Jeff will install a Climma if one insists, but in our case, we were leaving for Canada when our factory-original aft Climma blew up most spectacularly, and Coastal is a horrible company that would only provide the Climma we needed with a 3 month+ lead time.  So we went with the Airr.

Jeff re-did our refrigeration with all new Frigoboat stuff and he did a great job, too.

Cheerio,

Peregrinus
SM2K Nr. 350
At anchor, Uvala Jaz (Budva), Montenegro



Re: [Amel Yacht Owners] Raymarine Autopilot problem

Paul Osterberg
 

Thank you Bill, we will make something similar when season is over
Paul on S/Y Kerpa SM#259