Date   

Re: [Amel Yacht Owners] main engine prop seals

Richard Piller <richard03801@...>
 

Dave, Be sure to replace the rubber o-ring seal in the
new bushing. Second. Use the old bushing to push the
new seals in... be sure there are no burrs or bumps on
the old bushing... This makes sure that you get an
even push on the new seals and don't damage anything.
Good luck
Richard and Joan SM 209
--- drdavegoodman <drdavegoodman@gmail.com> wrote:

I have just changed the main engine prop seals with
the bushing and
seals obtained from Amel. A special proper
extractor tool or 3/way
puller was needed, which we fashioned in the yard
I'm in (Independent
Boat Yard Marina on St. Thomas, USVI). When
inserting the new seals,
we used a large cutlass bearing (large brass
cylinder) that was about
the same outer diameter as the new seals to seat the
new seals in
place. I wonder what others have used for this
process of re-seating
the new seals.
Thanks
Dave


__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com


Re: [Amel Yacht Owners] More Inland Waterway Questions

Dr. Seidel <mseidel@...>
 

calll the corps of engineers navigation section and go with the charts. They are very helpful. Usually you can get under all the 65 foot bridges by waiting for low tide slack water, then wait on the other side 2houors to deepen the water. Murray seidel sm349 910-470-1225

----- Original Message -----
From: Thomas Peacock
To: amelyachtowners@yahoogroups.com
Sent: Thursday, October 18, 2007 11:36 AM
Subject: Re: [Amel Yacht Owners] More Inland Waterway Questions


We own SM #240 and are also headed south from the Chesapeake to South
Carolina in three weeks.

I assume you are talking about going through the ICW; unfortunately,
while the regulations call for a depth of 12 feet, it has been much
neglected over the past few years and has silted up in many areas.
Postings in chat rooms talk about a five foot depth in some spots; I
motored the ICW in a previous boat six years ago, and at times bumped
with a six foot keel. I don't see any alternative for you except the
outside route around Hatteras. There is no place to put in between
Norfolk and Beaufort, NC. Be sure to allow yourself a reasonable
weather window; with planning, it should not be much of a problem,
but the conditions around Hatteras are very fluky and can change
quickly. Always an adventure, but your boat should be able to handle
most of what Hatteras can throw at you.

Tom Peacock
Aletes SM 240

On Oct 18, 2007, at 10:52 AM, blowinahoudy wrote:

> We are fairly new members of the group and are heading south from
> Maine in two days.
>
> Has anyone talen a 53' Super Maramu from Norfolk, VA. to Beaufort, NC.
> recently. We are especially concerned about bridge heights and water
> depth. Any help would be greatly appreciated.
>
> Thanks,
> Joe #86
> "Brown-Eyed Girl"
>
>
>


Re: [Amel Yacht Owners] More Inland Waterway Questions

Dr. Seidel <mseidel@...>
 

The bridge at Snows Cut south of wrightsville beach, nc. can be navigated at dead low tide ( the tide time given for carolina beach inlet ( south of Masonboro inlet). I take my Sm #349 through frequently, but be prepared to pass caroline beach inlet 2hours earlier and anchor in entrance to the cul de sac leading to the town center of carolina beach. The docks on the south of snowns cut in the cul de sac are not deep enough for the 6.5 feet as the tide drops. Murray Seidel "sundance" . 910-470-1225. Also suggest going to the corps of engineer's office and taking charts and speaking with the navigation section people. They are very helpful.

----- Original Message -----
From: blowinahoudy
To: amelyachtowners@yahoogroups.com
Sent: Thursday, October 18, 2007 9:52 AM
Subject: [Amel Yacht Owners] More Inland Waterway Questions


We are fairly new members of the group and are heading south from
Maine in two days.

Has anyone talen a 53' Super Maramu from Norfolk, VA. to Beaufort, NC.
recently. We are especially concerned about bridge heights and water
depth. Any help would be greatly appreciated.

Thanks,
Joe #86
"Brown-Eyed Girl"


Re: [Amel Yacht Owners] Quantity of bowthruster oil

BeyersWF
 

Dave, Bel Ami,

My bowthruster has a small see-through reservoir mounted in the
port side cabinet in the V-birth with a feed tube down to the bowthruster.
It is easy to monitor the fluid level and add the 90 weight oil. The
reservoir holds about 0.3 liters.

Crash, WINDRUSH, Mango No. 29



From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of drdavegoodman
Sent: Friday, November 09, 2007 7:27 AM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] Quantity of bowthruster oil



Greetings all;
I have the bowthruster out for changing oil and seals. I have gotten
conflicting info regard quantity of 90 weight oil to put in. One
source says .3 liters, the other source 3/4 quart, which is much more.
Any quick advice is appreciated!
Dave
s/v Bel Ami
SM #230


Re: [Amel Yacht Owners] main engine prop seals

Rob Brennan <brennan@...>
 

Dave

I use the old brass bush reversed.

Rob on Nebo SM251



From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of drdavegoodman
Sent: Sunday, 11 November 2007 12:55 AM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] main engine prop seals



I have just changed the main engine prop seals with the bushing and
seals obtained from Amel. A special proper extractor tool or 3/way
puller was needed, which we fashioned in the yard I'm in (Independent
Boat Yard Marina on St. Thomas, USVI). When inserting the new seals,
we used a large cutlass bearing (large brass cylinder) that was about
the same outer diameter as the new seals to seat the new seals in
place. I wonder what others have used for this process of re-seating
the new seals.
Thanks
Dave


main engine prop seals

drdavegoodman
 

I have just changed the main engine prop seals with the bushing and
seals obtained from Amel. A special proper extractor tool or 3/way
puller was needed, which we fashioned in the yard I'm in (Independent
Boat Yard Marina on St. Thomas, USVI). When inserting the new seals,
we used a large cutlass bearing (large brass cylinder) that was about
the same outer diameter as the new seals to seat the new seals in
place. I wonder what others have used for this process of re-seating
the new seals.
Thanks
Dave


Re: [Amel Yacht Owners] Quantity of bowthruster oil

drdavegoodman
 

Great. I used .3 liters after changing all the seals, including the
prop seal. No problems!

Dave


Re: [Amel Yacht Owners] Email Problems....

Anne & John Hollamby <annejohn@...>
 

Well done Ian and Judy.........Now you are showing something between your top and bottoms
--Congratulations, John, SM 319

--- Original Message -----
From: "Ian & Judy Jenkins" <ianjudyjenkins@hotmail.com>
To: <amelyachtowners@yahoogroups.com>
Sent: Friday, November 09, 2007 8:06 PM
Subject: RE: [Amel Yacht Owners] Email Problems....



Thanks, Steve. I have now run my scans. Picked up one virus. It will be interesting to see if this gets through! cheers, Ian and Judy, Pen Azen
https://www.celebmashup.com





Yahoo! Groups Links




Re: [Amel Yacht Owners] Quantity of bowthruster oil

Richard Piller <richard03801@...>
 

Dave, We just did ours yesterday here in Annapolis. A
good grade of 90 wt. in exactly the quanity you need
is available at most boat supply store in the outboard
sections. A tube of oil can be poured right in and
that is enough. Better still using the "tube" you
don't have a smelly bottle laying about. If gear lube
spills it's on hell of a smelly mess..
Good luck and fair seas.
Richard and Joan SM 209
--- drdavegoodman <drdavegoodman@gmail.com> wrote:

Greetings all;
I have the bowthruster out for changing oil and
seals. I have gotten
conflicting info regard quantity of 90 weight oil to
put in. One
source says .3 liters, the other source 3/4 quart,
which is much more.
Any quick advice is appreciated!
Dave
s/v Bel Ami
SM #230


__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com


Re: [Amel Yacht Owners] Quantity of bowthruster oil

Naegels Patrick <naegels@...>
 

Yes, I confirm 0.3 litre of SAE 90 oil. It's easier to fill with an
oil tin with an tip cap.

Patrick Naegels from SM 2000 Caramel

°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°
--- In amelyachtowners@yahoogroups.com, "Rob Brennan" <brennan@...>
wrote:

0.3litre of 90 grade is fresh info I have from Amel!

Rob on Nebo SM251



From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of drdavegoodman
Sent: Friday, 9 November 2007 11:27 PM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] Quantity of bowthruster oil



Greetings all;
I have the bowthruster out for changing oil and seals. I have gotten
conflicting info regard quantity of 90 weight oil to put in. One
source says .3 liters, the other source 3/4 quart, which is much
more.
Any quick advice is appreciated!
Dave
s/v Bel Ami
SM #230





[Non-text portions of this message have been removed]


Re: [Amel Yacht Owners] Quantity of bowthruster oil

Rob Brennan <brennan@...>
 

0.3litre of 90 grade is fresh info I have from Amel!

Rob on Nebo SM251



From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of drdavegoodman
Sent: Friday, 9 November 2007 11:27 PM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] Quantity of bowthruster oil



Greetings all;
I have the bowthruster out for changing oil and seals. I have gotten
conflicting info regard quantity of 90 weight oil to put in. One
source says .3 liters, the other source 3/4 quart, which is much more.
Any quick advice is appreciated!
Dave
s/v Bel Ami
SM #230


Re: [Amel Yacht Owners] Email Problems....

ianjenkins1946 <ianjudyjenkins@hotmail.com>
 

Thanks, Steve. I have now run my scans. Picked up one virus. It will be interesting to see if this gets through! cheers, Ian and Judy, Pen Azen
https://www.celebmashup.com

[Non-text portions of this message have been removed]


Quantity of bowthruster oil

drdavegoodman
 

Greetings all;
I have the bowthruster out for changing oil and seals. I have gotten
conflicting info regard quantity of 90 weight oil to put in. One
source says .3 liters, the other source 3/4 quart, which is much more.
Any quick advice is appreciated!
Dave
s/v Bel Ami
SM #230


Email Problems....

featherwind <featherwind@...>
 

If anyone has been having some problems with email or losing messages as
below, it may be because of a virus. I cleaned a "Trojan" virus off of a
couple of emails that I received from the group and emailed them about it.
I recommend everyone run a virus scan of their computers.
Steve Munro

-----Original Message-----
From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of Ian & Judy Jenkins
Sent: Tuesday, November 06, 2007 10:42 AM
To: amelyachtowners@yahoogroups.com
Subject: [Amel Yacht Owners] Antifouling /Coppercoat


Hi Anne and John, It seems that hotmail will allow me to write a fresh
email but somehow confiscates the text from any reply that I do.( If anyone
reading this knows why this should be, please can they let me know?)
My deleted replies were to thank you for your chum's observations on
Coppercoat--rather different from those on the website...
The orange peel comment rings a bell from something I read a few years ago.
I wonder if they have now changed the mix? It needs to be rolled on , using
very small quantities, one litre at a time, mixing vigorously.
I see that Mr Matthews now puts it on his new Oystercatcher so maybe they
are having more success with its application.I need to do some more
research. Cheers, Ian and Judy, Pen Azen
_________________________________________________________________
100's of Music vouchers to be won with MSN Music
https://www.musicmashup.co.uk






Yahoo! Groups Links


Re: Antifouling /Coppercoat

Jose_Luis Isasi <jose.luis.isasi@...>
 

Hi,

I have post a question to Yahoo on this. We´ll see.

Jose_Luis




--- In amelyachtowners@yahoogroups.com, Ian & Judy Jenkins
<ianjudyjenkins@...> wrote:


Hi Anne and John, It seems that hotmail will allow me to write a
fresh email but somehow confiscates the text from any reply that I do.
( If anyone reading this knows why this should be, please can they
let me know?)
My deleted replies were to thank you for your chum's observations
on Coppercoat--rather different from those on the website...
The orange peel comment rings a bell from something I read a few
years ago. I wonder if they have now changed the mix? It needs to be
rolled on , using very small quantities, one litre at a time, mixing
vigorously.
I see that Mr Matthews now puts it on his new Oystercatcher so
maybe they are having more success with its application.I need to do
some more research. Cheers, Ian and Judy, Pen Azen
_________________________________________________________________
100's of Music vouchers to be won with MSN Music
https://www.musicmashup.co.uk

[Non-text portions of this message have been removed]


Antifouling /Coppercoat

ianjenkins1946 <ianjudyjenkins@hotmail.com>
 

Hi Anne and John, It seems that hotmail will allow me to write a fresh email but somehow confiscates the text from any reply that I do.( If anyone reading this knows why this should be, please can they let me know?)
My deleted replies were to thank you for your chum's observations on Coppercoat--rather different from those on the website...
The orange peel comment rings a bell from something I read a few years ago. I wonder if they have now changed the mix? It needs to be rolled on , using very small quantities, one litre at a time, mixing vigorously.
I see that Mr Matthews now puts it on his new Oystercatcher so maybe they are having more success with its application.I need to do some more research. Cheers, Ian and Judy, Pen Azen
_________________________________________________________________
100s of Music vouchers to be won with MSN Music
https://www.musicmashup.co.uk

[Non-text portions of this message have been removed]


Antifouling/Coppercoat

ianjenkins1946 <ianjudyjenkins@hotmail.com>
 

My last three replies under this heading have had my text deleted, for reasons that I do not understand. This is sent as a new message to see if it behaves differently. Ian Jenkins. Pen Azen
_________________________________________________________________
100s of Music vouchers to be won with MSN Music
https://www.musicmashup.co.uk

[Non-text portions of this message have been removed]


Re: [Amel Yacht Owners] Antifouling/Copperbot

ianjenkins1946 <ianjudyjenkins@hotmail.com>
 

Celeb spotting Play CelebMashup and win cool prizes
https://www.celebmashup.com


Re: [Amel Yacht Owners] Antifouling/Copperbot

John and Anne on Bali Hai <annejohn@...>
 

--- In amelyachtowners@yahoogroups.com, Ian & Judy Jenkins
<ianjudyjenkins@...> wrote:

Get free emoticon packs and customisation from Windows Live.
http://www.pimpmylive.co.uk

[Non-text portions of this message have been removed]
Hello again,
Your last two messages have not appeared on the site so something is
fouled up. All I see is the subject and then nothing except the ads at
the end.
Regards Anne and John SM319


Re: [Amel Yacht Owners] Antifouling/Copperbot

ianjenkins1946 <ianjudyjenkins@hotmail.com>
 

Get free emoticon packs and customisation from Windows Live.
http://www.pimpmylive.co.uk