Date   

Re: [Amel Yacht Owners] Turbo Rebuild

Mike Ondra
 

Pat,

I was afraid you’d ask that. I didn’t say because I couldn’t remember. As I recall I did drop it off to their shop on the way home from Rock Hall, but I don’t recall why they felt it was not rebuildable.

Sorry for the non-informational answer.

Mike

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Thursday, September 21, 2017 6:14 AM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Turbo Rebuild

 

 

Mike, Why did you opt to replace to turbo , rather than have it rebuilt? Thanks for the info , I will contact them.

Pat 

SM#123

-----Original Message-----
From: 'Mike Ondra' mdondra@... [amelyachtowners] <amelyachtowners@...>
To: amelyachtowners <amelyachtowners@...>
Sent: Wed, Sep 20, 2017 4:06 pm
Subject: RE: [Amel Yacht Owners] Turbo Rebuild

 

Hi Pat.

 

We replaced our turbo in 2013. Purchased from Marine Parts Express in Maine (google it) and received great service. They seemed to know Volvo/Penta quite well.  Price was $1750 plus $500 for the core which was refunded when I shipped the old one back to them. Additionally there were 2 gaskets at about $25 each.

 

Also you might try Blouch Performance Turbo in Lebanon, PA. 717-865-3276. I found them helpful. They are a Garrett Turbo shop, and at least on Aletes our turbo was a Garrett. They rebuild. Garrett has a troubleshooting guide on their website and other information more than you may want to look at.

 

Mike Ondra

Aletes SM#240

Rock Hall, MD

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Wednesday, September 20, 2017 7:49 AM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Turbo Rebuild

 

 

Paul. I am dealing with a turbine that is not spinning freely , and started the previous thread . I would be taking  the turbo off this week to clean ,if possible , if not send it out to rebuild. I am reluctant to remove it now as Hurricane Maria may approach the east coast next week and I want to be able to move my boat. We are planning to leave on a trip down the C Bay in about a week and won't have time to rebuild before we leave . I was wondering if we did not push the throttle beyond 2000 rpm (top rpm now) if it would be safe to operate the boat without doing any damage to the engine. I had this turbo rebuilt three years ago at a cost of aprox. $ 800.00 . I am presently looking for the name of the turbo shop , to use again if needed .

Good Luck ,

Pat

SM #123

-----Original Message-----
From: pwschofield@... [amelyachtowners] <amelyachtowners@...>
To: amelyachtowners <amelyachtowners@...>
Sent: Tue, Sep 19, 2017 5:25 pm
Subject: [Amel Yacht Owners] Turbo Rebuild

 

Hello everyone.  Lately there has been a thread regarding RPMs.  This is a problem that I've had with our Volvo since we purchased the boat a year ago.  I had always feared it was the turbo since I never could hear that telltale turbo whine.  Well today, my suspicions were confirmed.  The turbo is seized solid.  

 

So now I look at my options.  My current web search doesn't seem to be yielding many sources, so I turn to the group to pick your collective brain.  

 

Has anyone had any experience with or know someone who has rebuilt a turbo off of the TMD22?   Is rebuilding a turbo economical?  

 

Does anyone know a source for a new turbo?  

 

And if you'll indulge me, I'll ask a third question that I'm sure will solicit some colorful comments.  Let me preface the question with a couple observations.  1.  Turbo chargers in a marine environment seem to have a lot of associated problems.  2.  I've been running the boat this last year including motoring from Ft. Lauderdale to Brunswick, GA in a head sea, and the boat seems to run well and I can achieve 6+ knots with no problem except I cannot exceed 2000rpm.  

 

So here's my questions.  What is the downside to removing the turbo altogether, short of a few horsepower and a knot or two?  

 

OK, putting on my Kevlar underwear.  

 

Turbo part number reference: Perkins p/n 2674A120

 

Paul

SM215

SV Trillium

 

 


Re: [Amel Yacht Owners] Re: Bilge maitenance

jhe1313@...
 

Thanks much everyone. I will give these suggestions a try! Best regards from Corfu! Cheers. Joerg


Re: [Amel Yacht Owners] Turbo Rebuild

Patrick McAneny
 

Mike, Why did you opt to replace to turbo , rather than have it rebuilt? Thanks for the info , I will contact them.
Pat 
SM#123


-----Original Message-----
From: 'Mike Ondra' mdondra@... [amelyachtowners] <amelyachtowners@...>
To: amelyachtowners
Sent: Wed, Sep 20, 2017 4:06 pm
Subject: RE: [Amel Yacht Owners] Turbo Rebuild

 
Hi Pat.
 
We replaced our turbo in 2013. Purchased from Marine Parts Express in Maine (google it) and received great service. They seemed to know Volvo/Penta quite well.  Price was $1750 plus $500 for the core which was refunded when I shipped the old one back to them. Additionally there were 2 gaskets at about $25 each.
 
Also you might try Blouch Performance Turbo in Lebanon, PA. 717-865-3276. I found them helpful. They are a Garrett Turbo shop, and at least on Aletes our turbo was a Garrett. They rebuild. Garrett has a troubleshooting guide on their website and other information more than you may want to look at.
 
Mike Ondra
Aletes SM#240
Rock Hall, MD
 
From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Wednesday, September 20, 2017 7:49 AM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Turbo Rebuild
 
 
Paul. I am dealing with a turbine that is not spinning freely , and started the previous thread . I would be taking  the turbo off this week to clean ,if possible , if not send it out to rebuild. I am reluctant to remove it now as Hurricane Maria may approach the east coast next week and I want to be able to move my boat. We are planning to leave on a trip down the C Bay in about a week and won't have time to rebuild before we leave . I was wondering if we did not push the throttle beyond 2000 rpm (top rpm now) if it would be safe to operate the boat without doing any damage to the engine. I had this turbo rebuilt three years ago at a cost of aprox. $ 800.00 . I am presently looking for the name of the turbo shop , to use again if needed .
Good Luck ,
Pat
SM #123

-----Original Message-----
From: pwschofield@... [amelyachtowners] <amelyachtowners@...>
To: amelyachtowners <amelyachtowners@...>
Sent: Tue, Sep 19, 2017 5:25 pm
Subject: [Amel Yacht Owners] Turbo Rebuild
 
Hello everyone.  Lately there has been a thread regarding RPMs.  This is a problem that I've had with our Volvo since we purchased the boat a year ago.  I had always feared it was the turbo since I never could hear that telltale turbo whine.  Well today, my suspicions were confirmed.  The turbo is seized solid.  
 
So now I look at my options.  My current web search doesn't seem to be yielding many sources, so I turn to the group to pick your collective brain.  
 
Has anyone had any experience with or know someone who has rebuilt a turbo off of the TMD22?   Is rebuilding a turbo economical?  
 
Does anyone know a source for a new turbo?  
 
And if you'll indulge me, I'll ask a third question that I'm sure will solicit some colorful comments.  Let me preface the question with a couple observations.  1.  Turbo chargers in a marine environment seem to have a lot of associated problems.  2.  I've been running the boat this last year including motoring from Ft. Lauderdale to Brunswick, GA in a head sea, and the boat seems to run well and I can achieve 6+ knots with no problem except I cannot exceed 2000rpm.  
 
So here's my questions.  What is the downside to removing the turbo altogether, short of a few horsepower and a knot or two?  
 
OK, putting on my Kevlar underwear.  
 
Turbo part number reference: Perkins p/n 2674A120
 
Paul
SM215
SV Trillium
 
 


Re: Turbo Rebuild

mfmcgovern@...
 

I was recommended to go to this place for rebuilds from a Garrett turbocharger dealer: http://gpopshop.com/services/rebuilding/

These guys apparently specialize in rebuilding turbochargers.

I called them and they can do a rebuild on that turbocharger. Assuming there is no damage to the shaft or wheels, they charge $350 for the rebuild of that turbo which is really cheap. If they have to replace the turbine wheel, shaft, compressor wheel or center cartridge it will start to get much more expensive. They charge a $75 inspection fee but ONLY if you DO NOT have them do any work. If they do the rebuild for you, there is no assessment fee.

Note, I do not have any personal experience with them or their services. They were just recommended to me by a Garrett dealer.

Another viable option if there is wheel or shaft damage is to buy a new complete replacement CHRA (Center Housting and Rotating Assembly): http://www.invasionautoproducts.com/gatbchca447.html

It the main "guts" of the turbocharger. You would re-use the original turbine housing, compressor housing and wastegate as those parts rarely fail. With this you have essentially a brand new turbocharger for way less money.

Hope that helps some of you.

Mark McGovern
SM #440 Cara
Deale, MD USA


Re: Amel SM 2000 windless switch

greatketch@...
 

Be sure to check the diameter of the hole...  I forget if they are 16, or 22 mm...  similar style switches are available in each size.

For what it is worth, I don't think of these as an alternative because they are cheaper, but because they are a more robust design.

Bill Kinney
SM160, Harmonie
Annapolis, MD


Re: [Amel Yacht Owners] Turbo Rebuild

Mike Ondra
 

Hi Pat.

 

We replaced our turbo in 2013. Purchased from Marine Parts Express in Maine (google it) and received great service. They seemed to know Volvo/Penta quite well.  Price was $1750 plus $500 for the core which was refunded when I shipped the old one back to them. Additionally there were 2 gaskets at about $25 each.

 

Also you might try Blouch Performance Turbo in Lebanon, PA. 717-865-3276. I found them helpful. They are a Garrett Turbo shop, and at least on Aletes our turbo was a Garrett. They rebuild. Garrett has a troubleshooting guide on their website and other information more than you may want to look at.

 

Mike Ondra

Aletes SM#240

Rock Hall, MD

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Wednesday, September 20, 2017 7:49 AM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Turbo Rebuild

 

 

Paul. I am dealing with a turbine that is not spinning freely , and started the previous thread . I would be taking  the turbo off this week to clean ,if possible , if not send it out to rebuild. I am reluctant to remove it now as Hurricane Maria may approach the east coast next week and I want to be able to move my boat. We are planning to leave on a trip down the C Bay in about a week and won't have time to rebuild before we leave . I was wondering if we did not push the throttle beyond 2000 rpm (top rpm now) if it would be safe to operate the boat without doing any damage to the engine. I had this turbo rebuilt three years ago at a cost of aprox. $ 800.00 . I am presently looking for the name of the turbo shop , to use again if needed .

Good Luck ,

Pat

SM #123

-----Original Message-----
From: pwschofield@... [amelyachtowners] <amelyachtowners@...>
To: amelyachtowners <amelyachtowners@...>
Sent: Tue, Sep 19, 2017 5:25 pm
Subject: [Amel Yacht Owners] Turbo Rebuild

 

Hello everyone.  Lately there has been a thread regarding RPMs.  This is a problem that I've had with our Volvo since we purchased the boat a year ago.  I had always feared it was the turbo since I never could hear that telltale turbo whine.  Well today, my suspicions were confirmed.  The turbo is seized solid.  

 

So now I look at my options.  My current web search doesn't seem to be yielding many sources, so I turn to the group to pick your collective brain.  

 

Has anyone had any experience with or know someone who has rebuilt a turbo off of the TMD22?   Is rebuilding a turbo economical?  

 

Does anyone know a source for a new turbo?  

 

And if you'll indulge me, I'll ask a third question that I'm sure will solicit some colorful comments.  Let me preface the question with a couple observations.  1.  Turbo chargers in a marine environment seem to have a lot of associated problems.  2.  I've been running the boat this last year including motoring from Ft. Lauderdale to Brunswick, GA in a head sea, and the boat seems to run well and I can achieve 6+ knots with no problem except I cannot exceed 2000rpm.  

 

So here's my questions.  What is the downside to removing the turbo altogether, short of a few horsepower and a knot or two?  

 

OK, putting on my Kevlar underwear.  

 

Turbo part number reference: Perkins p/n 2674A120

 

Paul

SM215

SV Trillium

 

 


Re: [Amel Yacht Owners] Head swivel

Danny and Yvonne SIMMS
 

Do share the result with us

Regards

Danny

On 21 September 2017 at 07:00 "Jean Broersen cestsibon1@... [amelyachtowners]" <amelyachtowners@...> wrote:

 

Thank you all for your excellent advise, will head swivel with hot fresh water first. If this not work then we will disassemble unit.

Thanks again
C'est si Bon


 


Head swivel

John Broersen
 

Thank you all for your excellent advise, will head swivel with hot fresh water first. If this not work then we will disassemble unit.

Thanks again
C'est si Bon


Re: [Amel Yacht Owners] Re: Bilge maitenance

Danny and Yvonne SIMMS
 

Hi Bill,

we did the same and I posted about it a couple of weeks ago. I agree it works well.

Danny

SM 299 Ocean Pearl

On 21 September 2017 at 01:36 "greatketch@... [amelyachtowners]" <amelyachtowners@...> wrote:

 

It is impossible to stop the bilge from smelling, but it is easy to keep the smell out of the boat.


The previous owner of Harmonie came up with this one, so I can not claim credit, but it is the best kind of idea, simple, low tech, and totally effective.

Where the hoses drain into the bilge, use three elbows and three short lengths of hose to make little "U" traps.   Works a charm.  Best if you make them so they are easily removable for easier access when it is time to clean the bilge.

Bill Kinney
SM160, Harmonie
Annapolis, MD


 


 


Re: Amel SM 2000 windless switch

Duane Siegfri
 

Bill K

That's a great price!  The Vetus product is $40 and this one only $6.  I'm ordering one just to see what it looks like.

Duane'
Wanderer, SM#477


Re: [Amel Yacht Owners] Re: Raymarine or B&G

Bill & Judy Rouse <yahoogroups@...>
 

Ron,

Thanks for that very detailed explanation.

Best,

CW Bill Rouse
Admiral, Texas Navy
Commander Emeritus

Amel School  http://www.amelschool.com
720 Winnie St
Galveston Island, TX 77550

+1(832) 380-4970




On Wed, Sep 20, 2017 at 3:15 AM, Ron Hynes riffhynes@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Last Summer I had trouble with my B&G Autopilot.  I called their service department in the UK but due to overflow I was told routed to Germany.  A very helpful tech ran me through a few tests and told me my Rudder Indicator had failed.  I obtained a new one for about 385 Euros.  Installed and no change in the operation.  Again, I called tech support in the UK.  This time I was asked for my "Installation Certificate Number".  I called the dealer where I bought the autopilot, radar, wind and speed, VHF, etc. (boat had been struck by lightning), but there was no answer.  I had remembered the previous year that the dealer shutdown for a 2-week vacation and although I didn't remmember the specific dates, thought this might be the reason.  I again called the UK to relay the fact that my dealer was not answering and that I had no idea what an ICN was.  They too called the dealer and confirmed he wasn't answering.

BUT all the information was in their computer.  They knew the serial number of my unit and when it had been purchased.

I learned that B&G markets their products at retail through normal marine supply houses but also has certified installers who have paid 2500 Euros to attend training.  The difference for the consumer is that in the event of a warranty issue, if you have a ICN, the service is done on your vessel at no charge.  For those that simply purchased the equipment from a retailer, you are on the hook for labor, travel, shipping, etc.

Since my problem was obviously the Autopilot computer (I could activate the mechanism, the rudder indicator was new and that's the entire system aside from the display and the keypad), I said why not take my credit card number and charge it for the computer and when I return the defective unit credit me back the charge.  Oh no, we can't do that.  We can only ship the replacement unit to a qualified dealer who will then make an appointment with you to install the computer.  I was to pay the dealer independently for his time.  I ended up paying just over 200 Euros and as it turns out was worth every penny as the tech from Dahlberg in Palma de Marjorca was excellent and adjusted the AP so that it worked better than it ever had before.

I'm a little miffed, however, over the entire episode.  How is a consumer supposed to know that there are retailers and there are certified installers?  Both display the same B&G banner in their stores.  The UK tech guy told me I should have gone to the B&G website and learned which are certified??  Interestingly, when I did go to the website and look, I learned that indeed they did have different symbols for certified installers but there was no legend to identify them.

On Tue, Sep 19, 2017 at 8:17 PM, greatketch@... [amelyachtowners] <amelyachtowners@yahoogroups.com> wrote:
 

Paul


I stayed with B&G brand instruments.

I think it is important to remember that B&G is no longer the independent company doing it's own thing the way it used to be.  For some time now it has been just one more brand in the Navico stable of products.  It is the brand name used to sell to sailboat owners the same products that Lawrence sells to fisherman, and Simrad sells to powerboaters.

Why I stayed with B&G:  I was used to them.  I had them on my old boat, and back when I made that selection, a long time ago, I felt that the B&G line was better suited to a cruising sailboat.  

The original equipment installed on any of the Super Marmus is dated enough that you really will have very little benefit in connecting them to a current Raymarine as opposed to another brand.

In a modern network, pretty much everything talks on the same protocol, even if they use different plugs.  On our boat we have a Raymarine AIS that came with the boat that we connected into our NMEA2000 network with a simple adapter, and the B&G MFD understands it just fine.  With a little work, our original Autohelm works side by side with our new B&G AC42 autopilot, and they both share the use of either Raymarine drive.

There are some things that Navico clearly does better, and some things that Raymarine does better.  I am pretty sure either will work for anybody.

A very few times I have had to use the Navico/B&G tech service to sort out a problem. Invariably, the knowledge of the phone support staff was truly exceptional.  And that isn't something I say very often.

Bill Kinney
SM160, Harmonie
Annapolis, MD

---In amelyachtowners@...m, wrote :

Hello!

We thinking of replace the old B&G system, the ultrasonic speed sensor got smashed when we grounded.

The B&G system is old and probably anyhow on the end of it's lifespan.

We have a Raymarine plotter just two years old (The old Garmin was more user friendly) , we are very pleases with our old Autohelm Autopilot, but need redundancy so we will planning to install the Raymarine EV 400, and keep the two original drive units, keep the old control head and computes as spare.

To us it make sense to use Raymarine i the rest of the instrumentation wind speed depth etc.

Hopefully we do not need to adress his issues any more during our ownership of Kerpa, so we like to do the right thing.

You who have this set up, which I guess there are a few, are you satisfied with the Raymarine equipment's?

You who choose to stay with B&G what was the main reason for that?


Paul on SY Kerpa SM#259 Mill Creek next stop St Michels







--
Regards,
Ron Hynes



Re: Swivel head

svcharisma
 

John,
I recently rebuilt the swivel on Mango #62.  The bearings are steel, not the modern Delrin type.  Good news is that I was able to purchase the bearings and seals at a local bearing shop.  I had to take the unit to a machine shop to press it apart.  It is really not a great design, buy mine lasted more than 25 years before it was a problem.
 
Alan Spence
707-738-9340 cell
svcharisma@...
the Adventure has just begun
~~~~~~~_/)~~ ~~~~~


Re: Amel sharki

hanoah64@...
 

Miles,

My genoa is about 135%, 7.5 oz. cruising cloth. I had an identical sail made using 6.5 oz with a torqueless Spectra luff for the Facnor. I found the sail to be too heavy, so I changed the luff and now it is a spare sail. Then Ullman Sails in Durban made a Gennaker, or Aymmetric or Screecher, (whatever) out of 2 or 2.5 oz and that works much better on the Facnor. With the Facnor set up you use a built in Spectra luff and a Spectra halyard with a double block to increase purchase. The Ullman Screecher is only slightly bigger than my genoa. The Facnor attaches to the port bow roller.
Cheers, Roger


Re: Turbo Rebuild

philipp.sollberger@...
 

Hi Paul,

I had the problem with my old turbo charger that it didn't activate because it was seized.
I asked the technician from Secodi in La Rochelle.
They tried to rebuild it but unfortunately they couldn't because the turbo was totally full of solid carbon and we couldn't change the rotor wheel.
As last solution they have searched for a new one and they installed it.
Since then I'm happy with my new turbo charger.

To rebuild a turbo by a technichian is possible, but I think, it is only successful, if you realize the non function just at the first time and you deinstall  it and rebuild it by a engine marine turbo specialist.

I have the same pn from perkins installed this early summer and I paid for the whole turbo charger reparation round 1 K€ with VAT.

How is the situation in the states I don't know. But I'm sure that they can deliver it also from Europe to USA  or Caribbean.

Good luck and fair winds.
I have deep feelings for all the damaged people and yachts by hurricane Irma and Maria.

Philipp
Félicie SM124  


Re: [Amel Yacht Owners] Re: Bilge maitenance

JOHN HAYES
 

Hi from ST Petersberg

Well without the benefit of recent emails I tipped a couple of litres of bleach down each shower sump which got rid of the smell for a few days but it returned.....

So then got hold of some liquid clothes washing soap and tipped a couple of litres down each shower sump. This has dealt to the issue for 8 months now.

Best 

John Hayes (normally in NZ)

On 20/09/2017, at 4:36 PM, greatketch@... [amelyachtowners] <amelyachtowners@...> wrote:

 

It is impossible to stop the bilge from smelling, but it is easy to keep the smell out of the boat.


The previous owner of Harmonie came up with this one, so I can not claim credit, but it is the best kind of idea, simple, low tech, and totally effective.

Where the hoses drain into the bilge, use three elbows and three short lengths of hose to make little "U" traps.   Works a charm.  Best if you make them so they are easily removable for easier access when it is time to clean the bilge.

Bill Kinney
SM160, Harmonie
Annapolis, MD



Re: [Amel Yacht Owners] Iridium Go Feedback

karkauai
 

Hi Thomas,
I don't have the GO, but use my Iridium phone with AxcessPoint gadget that creates a wifi hotspot similar to the GO.  I found that Signal was frequently lost and erratic.  I'm just adding a permanent antenna on my new arch, will report on its efficacy.
Kent
SM243
Kristy



Re: [Amel Yacht Owners] Re: Bilge maitenance

Aldo Roldan
 

Have you tried vinegar (disolved with water in various proportions)?  It works for cleaning, for glass, mirrors for mold, for musty wood, and for odors.  For many applications it beats the manufactured supermarket type products.  We have become great fans of this humble traditional product.


On Sep 20, 2017, at 6:28 AM, jhe1313@... [amelyachtowners] <amelyachtowners@...> wrote:

 

thanks much for everyone's input.  I'm surprised nobody is using something to cut down on the smell.  3 days after a thorough cleaning with wetvac and all, it started smelling again.  The smell comes back up through the hoses in the galley and heads.  We're very "careful" with what goes down the sink but let's face it, something will always go down and it seems there should be a solution that keeps the smell away.  I've been experimenting with various products - I found a bilge cleaner in a small harbor in Italy that worked pretty well but it's used up now and I can't buy it again.  Cheers Joerg


Re: Bilge maitenance

greatketch@...
 

It is impossible to stop the bilge from smelling, but it is easy to keep the smell out of the boat.

The previous owner of Harmonie came up with this one, so I can not claim credit, but it is the best kind of idea, simple, low tech, and totally effective.

Where the hoses drain into the bilge, use three elbows and three short lengths of hose to make little "U" traps.   Works a charm.  Best if you make them so they are easily removable for easier access when it is time to clean the bilge.

Bill Kinney
SM160, Harmonie
Annapolis, MD



Re: [Amel Yacht Owners] Turbo Rebuild

Patrick McAneny
 

Paul. I am dealing with a turbine that is not spinning freely , and started the previous thread . I would be taking  the turbo off this week to clean ,if possible , if not send it out to rebuild. I am reluctant to remove it now as Hurricane Maria may approach the east coast next week and I want to be able to move my boat. We are planning to leave on a trip down the C Bay in about a week and won't have time to rebuild before we leave . I was wondering if we did not push the throttle beyond 2000 rpm (top rpm now) if it would be safe to operate the boat without doing any damage to the engine. I had this turbo rebuilt three years ago at a cost of aprox. $ 800.00 . I am presently looking for the name of the turbo shop , to use again if needed .
Good Luck ,
Pat
SM #123


-----Original Message-----
From: pwschofield@... [amelyachtowners]
To: amelyachtowners
Sent: Tue, Sep 19, 2017 5:25 pm
Subject: [Amel Yacht Owners] Turbo Rebuild

 
Hello everyone.  Lately there has been a thread regarding RPMs.  This is a problem that I've had with our Volvo since we purchased the boat a year ago.  I had always feared it was the turbo since I never could hear that telltale turbo whine.  Well today, my suspicions were confirmed.  The turbo is seized solid.  

So now I look at my options.  My current web search doesn't seem to be yielding many sources, so I turn to the group to pick your collective brain.  

Has anyone had any experience with or know someone who has rebuilt a turbo off of the TMD22?   Is rebuilding a turbo economical?  

Does anyone know a source for a new turbo?  

And if you'll indulge me, I'll ask a third question that I'm sure will solicit some colorful comments.  Let me preface the question with a couple observations.  1.  Turbo chargers in a marine environment seem to have a lot of associated problems.  2.  I've been running the boat this last year including motoring from Ft. Lauderdale to Brunswick, GA in a head sea, and the boat seems to run well and I can achieve 6+ knots with no problem except I cannot exceed 2000rpm.  

So here's my questions.  What is the downside to removing the turbo altogether, short of a few horsepower and a knot or two?  

OK, putting on my Kevlar underwear.  

Turbo part number reference: Perkins p/n 2674A120

Paul
SM215
SV Trillium



Re: Bilge maitenance

jhe1313@...
 

thanks much for everyone's input.  I'm surprised nobody is using something to cut down on the smell.  3 days after a thorough cleaning with wetvac and all, it started smelling again.  The smell comes back up through the hoses in the galley and heads.  We're very "careful" with what goes down the sink but let's face it, something will always go down and it seems there should be a solution that keeps the smell away.  I've been experimenting with various products - I found a bilge cleaner in a small harbor in Italy that worked pretty well but it's used up now and I can't buy it again.  Cheers Joerg