We are in the market for new sails, and got a reasonable offer from Incidence sails in France made in Hydranet. They do not use foam luff which surprise me they claim and they should now. So to my question. Is there any of you who recently bought sails from Incidence? what is your experience with the sails? especially the head sails does it furl/reef well?
I guess they have a lot of experience in building/making sails for Amel SM
Paul on SY Kerpa SM#259

We have noticed a strange ingress of water in our forward head bowl, when sailing with the wind in from SB, if there is any water left in the bowl, the bowl slowly fills with water, usually smal amount when the boats goes down in a wave or other vivid motion. If the bowl is totally empty no water coming in! I have no explanation to the behavior.  We have similar on the aft toilet but to much less extent. We always have the valve for emptying the holding tank open when at sea. but can't imagine how water can get in that way
Paul on SY Kerpa SM #259

Aletes locker drain was also blocked. Pushing a fish (wire puller) up the drain pipe from the T in the foreword head bilge broke it loose. Water gushed out along with the mud and sand. Hose pressure through the holes in the anchor locker floor cleaned out the rest. 

Key to this was the access now afforded      through the port bow locker floor now completed. 

Mike Ondra

Aletes SM240

<image1.jpeg>

On May 19, 2019, at 5:51 PM, Germain Jean-Pierre <jp.germain45@...> wrote:

Hi Gang,

I solved the problem by always using the chain wash (now fresh water on our boat) and at least once a year… doing a pressure wash in the chain well compartment.

Cheers from Fiji.

Jean-Pierre Germain, SY Eleuthera, SM 007

On 20 May 2019, at 09:45, Thomas Kleman <lorient422@...> wrote:

Mike- your floor looks great. I know how hard it is to cut and refine that shape. On L'ORIENT my chain locker bilge (under that glassed in perforated grate at the bottom of the chain locker) was hoplessly clogged. I ended up cutting an access port in it so I could vacuum it out periodically.....it drains fine now Wondering if other people have this problem or I just pick muddier places to anchor than most.....the actual outlet underneath there is about 15mm above the bottom and offset.

Aletes locker drain was also blocked. Pushing a fish (wire puller) up the drain pipe from the T in the foreword head bilge broke it loose. Water gushed out along with the mud and sand. Hose pressure through the holes in the anchor locker floor cleaned out the rest. 

Hi Gang,

I solved the problem by always using the chain wash (now fresh water on our boat) and at least once a year… doing a pressure wash in the chain well compartment.

Cheers from Fiji.

Jean-Pierre Germain, SY Eleuthera, SM 007

On 20 May 2019, at 09:45, Thomas Kleman <lorient422@...> wrote:

Mike- your floor looks great. I know how hard it is to cut and refine that shape. On L'ORIENT my chain locker bilge (under that glassed in perforated grate at the bottom of the chain locker) was hoplessly clogged. I ended up cutting an access port in it so I could vacuum it out periodically.....it drains fine now Wondering if other people have this problem or I just pick muddier places to anchor than most.....the actual outlet underneath there is about 15mm above the bottom and offset.

On 20 May 2019, at 09:45, Thomas Kleman <lorient422@...> wrote:

Mike- your floor looks great. I know how hard it is to cut and refine that shape. On L'ORIENT my chain locker bilge (under that glassed in perforated grate at the bottom of the chain locker) was hoplessly clogged. I ended up cutting an access port in it so I could vacuum it out periodically.....it drains fine now. Wondering if other people have this problem or I just pick muddier places to anchor than most.....the actual outlet underneath there is about 15mm above the bottom and offset.

On 20 May 2019 at 03:14 SV Trilogy <svtrilogy53@...> wrote:

Thanks everyone for the informative responses on this topic. We're having a new set of horns fabricated and plan to cover them with some hose material. Anything one can do to reduce halyard wraps, cuts, jams, etc. is certainly worthwhile.

On a side note, while up at the masthead I noticed the foil/extrusion was heavily scratched around it's circumference for several inches right where the top swivel would sit. Perhaps there's an issue with our top swivel and it should be taken apart and serviced? Although while at deck level it spins easily and sounds very smooth. Or maybe the threads on the one horn we had up there were too long and made contact with the foil while furling? Just wondering if anyone has ever seen anything similar on their boat. Sorry no photo at the moment but I'll try and get one.

Cheers,

Mike & Hannah

SV Trilogy, SM#23

Panama

On Mon, 13 May 2019, 08:05 Gary Wells, < gary@...> wrote:

A short piece of fuel line and some contact cement make good "caps" for those 'horns'.
Having experienced a halyard wrap up there once, I wouldn't consider running without them.
If you are doing regular maintenance on the swivel then it's far less likely the horns would touch the mast, but if the swivel jams even slightly the horns are the best defense against getting the halyard wrapped and broken at the masthead.  
Can't really explain how I discovered this.  :)

Gary W.
SM 209, "Adagio"
Beaufort, NC USA

 

 

Greg,

I'm not sure from your question: are you trying to unscrew them from the outside of the casing?

If so you need to remove the nuts on the aft of the windlass aluminum cover, then slide the cover aft.  You'll find a nut on the inside of the case on the switch.  Remove the wires first, then the nut.  Make sure you use a good sealant that you can get apart later to make the switches watertight to the case.  

If the rubber boot you mention is the surface you press on, it has a lip that goes under the actual hard plastic switch that lies beneath.  You'll have to remove the switch to replace that.

On my SM this is the proceedure for the Lofrans Tigres, but on older models it might be different.

Duane
Wanderer, SM#477