Date   
Re: AMEL 55 -2012 — Replacing CLIMA aircon unit systems with a schiller central unit

Jose Alegria
 

Bill, hi

Thank you very much for your opinion but I would like to detail the situation further and request your re-examination

The Amel 50 and 60 currently come equipped with a central chiller system  (Webasto ) and the last 55 at least from July 2017 have also been equipped with central chiller systems.

My actual situation: My 55 hull nº 3 comes with:
2 compact CLIMA in the aft cabin both of 3.5; in the saloon one of 7 plus other 12 and in the front  cabin another of 7; 5 equipments of a total of 33,000 btu, but 3,5 + 3,5 at the main cabin are clearly insufficient in places like Greece in July-August; They are totally ineffective and extremely noisy.
How to solve?
a) Installing new independent CLIMA or WEBASTO equipment,  increasing power in the aft cabin to at least 12-15 000BTU and benefiting from the fact that the most modern appliances have about 25% more cooling capacity,
b) keeping 5 equipment and also keeping the noise of the compressors in the noble spaces
or
following the current Amel philosophy by placing a WEBASTO  variable speed schiller  (Webasto V50) that drains only at 2.5 to 15 amp, not exceeding 5/8 amp in eco mode, and puts 5 air handlers (smaller than the compact units)
How change all pipes system?
Probably the path of the current saltwater circuit can be replaced by Schiller liquid (water and glycol).
I will also be able to take advantage of the condensate circuit to make the pipes pass through the same holes.
And maybe I need more new holes !....

I would be grateful for your more detailed appreciation of the issue.

Thanks in advance

Can you 

Re: Dishwasher top loading

Joerg Esdorn
 

No it replaces two drawers - no 2 and 3 from top.  I haven’t installed it - still thinking about it.  

Joerg

Re: Reckman EF90 Genoa furler

Joerg Esdorn
 

Type 2 for both Genoa and staysail.  

Joerg Esdorn
A55 #53
Kincsem

Re: Dishwasher top loading

Paul Brown
 

Thank you Joerg 

Did you install this to your 55 and if so what location?

In the early 55 model they installed a top-loader

Regards Paul 


On 13 Sep 2019, at 5:37 pm, Joerg Esdorn via Groups.Io <jhe1313@...> wrote:

Hi Paul, this is the unit Amel installs now.  BOSCH SKT 5102.  Let me know how you like it!!

joerg Esdorn 
A55#53
Kincsem
currently in Sevilla 

Re: Reckman EF90 Genoa furler

 

Although I can find nothing on Amel specifications, I believe that you will find that the Reckmann EF series comes in 3 sizes: EF-90, EF90-2, and EF90-3 and that the Reckmann EF-90 is installed on the 55 and a recommended replacement for bamar on the 54. 

If I were you, I would ask this question to SAV"at"Amel.fr.

--
CW Bill Rouse
Amel Yacht Owners School
Address: 720 Winnie, Galveston Island, Texas 77550 
   


On Fri, Sep 13, 2019 at 8:47 AM Aldo Roldan via Groups.Io <aroldan1796=yahoo.com@groups.io> wrote:
Question for the group.  What is the size of the Reckman EF90 Genoa electric furler in the AMEL 55? I have been told it would be either a 2 or a 3, but which one?

Aldo
AMEL 55 Hull 36

On Sep 11, 2019, at 3:55 PM, Roque <ediroque@...> wrote:

Alan

I recently bought from Amel. The rubber valve is a reinforced new version ( see pic)

1 [03028] KIT POMPE MARINA ZZ 219424/ Electric bilge pump repair kit  E$124,60 plus VAT
2 [03219] CLAPET ASPIRATION POMPE HENDERSON 72621/ Rubber valve for electric bilge pump E$17,42 each  34,84 plus VAT

Rgds

Roque
Attika A54 117
Paraty

Em qua, 11 de set de 2019 às 16:46, CW Bill Rouse <brouse@...> escreveu:
Amel - sav@... recently had them for the Marina ZZ
TF Marine makes an identical pump. It is either number TM-50 or TM-70...not sure. I cannot tell you where to find TF Marine spares, except at Amel...Amel replaced the reya pump with TF Marine.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Sep 11, 2019 at 2:33 PM Alan Grayson <bazgrayson@...> wrote:
Hi All, Does anyone know where to get the rebuild kits for the Reya Marina ZZ bilge pump. I got on the Reya website but if my translation is right they do not sell to individuals and a google search under their part numbers has not turned up any suppliers.
Regards
Alan Grayson
SM 406 Ora Pai
St Michaels, MD

<Kit pompe de cale électrique ref 3028.JPG>

Re: Dishwasher top loading

Joerg Esdorn
 

Hi Paul, this is the unit Amel installs now.  BOSCH SKT 5102.  Let me know how you like it!!

joerg Esdorn 
A55#53
Kincsem
currently in Sevilla 

Reckman EF90 Genoa furler

Aldo Roldan
 

Question for the group.  What is the size of the Reckman EF90 Genoa electric furler in the AMEL 55? I have been told it would be either a 2 or a 3, but which one?

Aldo
AMEL 55 Hull 36

On Sep 11, 2019, at 3:55 PM, Roque <ediroque@...> wrote:

Alan

I recently bought from Amel. The rubber valve is a reinforced new version ( see pic)

1 [03028] KIT POMPE MARINA ZZ 219424/ Electric bilge pump repair kit  E$124,60 plus VAT
2 [03219] CLAPET ASPIRATION POMPE HENDERSON 72621/ Rubber valve for electric bilge pump E$17,42 each  34,84 plus VAT

Rgds

Roque
Attika A54 117
Paraty

Em qua, 11 de set de 2019 às 16:46, CW Bill Rouse <brouse@...> escreveu:
Amel - sav@... recently had them for the Marina ZZ
TF Marine makes an identical pump. It is either number TM-50 or TM-70...not sure. I cannot tell you where to find TF Marine spares, except at Amel...Amel replaced the reya pump with TF Marine.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Sep 11, 2019 at 2:33 PM Alan Grayson <bazgrayson@...> wrote:
Hi All, Does anyone know where to get the rebuild kits for the Reya Marina ZZ bilge pump. I got on the Reya website but if my translation is right they do not sell to individuals and a google search under their part numbers has not turned up any suppliers.
Regards
Alan Grayson
SM 406 Ora Pai
St Michaels, MD

<Kit pompe de cale électrique ref 3028.JPG>

Re: [Amel Yacht Owners] Bow locker seals

eric freedman
 

Hi Kent,

Thanks

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of karkauai via Groups.Io
Sent: Thursday, September 12, 2019 10:33 PM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] [Amel Yacht Owners] Bow locker seals

 

I ordered from Amel, I haven’t received it yet, but Maud had several kinds.  I described what was originally installed and she said she’d send what appears to be the same.  It’s a D with all the walls the same, about 5mm thick all the way.  She didn’t know anything about the cylindrical piece that was described as placed into the D seals at the corners, and said they don’t have anything like that.

 

When I get it, I’ll take some pics and try to describe the material and compressibility.

Kent Robertson

S/V Kristy

SM243


On Sep 12, 2019, at 8:38 PM, eric freedman <kimberlite@...> wrote:

Hi Kent,

What gasket did you find for this job?

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of CW Bill Rouse
Sent: Sunday, August 04, 2019 4:10 PM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] [Amel Yacht Owners] Bow locker seals

 

Danny I am sure A represents what Amel installed, but since apparently all manufacturers have cheapened the foam by lowering the density. This is the reason that I believe I would replace it with B profile. 

 

That said, I will wait for a final judgement until after Kent has talked to the manufacturer.

 

Kent, you should ask: Is B better than A in situations where the compression will be greater than 25%. 

Best,

CW Bill Rouse
Yacht School - Supporting Amel Owners
www.YachtSchool.us
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970

 

On Sun, Aug 4, 2019, 2:23 PM Danny and Yvonne SIMMS <simms@...> wrote:

I would think A is closest to what I have on Ocean Pearl

Regards

Danny

SM 299

Ocen Pearl

On 05 August 2019 at 04:47 CW Bill Rouse <brouse@...> wrote:

I am resending this because the first email did not really look correct with HTML

 

 

 


A

B

C

D

E

R

Figure
Letter
(See Above)

CATALOG
NUMBER

Base Width

Wall

Open Height

Base T

Total Height

Radius

B

CACD240

1"

1/8"

9/16"

5/16"

1"

-

 

 

 

 

 

 

 

 

 

 

 

http://www.acmerubber.com/round.htm

 

 

 

 

Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sun, Aug 4, 2019 at 11:41 AM CW Bill Rouse via Groups.Io <brouse= gmail.com@groups.io> wrote:

Kent,

 

If I am not mistaken, they have exactly what I think will work best, which is CACD240:

 

 

 


A

B

C

D

E

R

Figure
Letter
(See Above)

CATALOG
NUMBER

Base Width

Wall

Open Height

Base T

Total Height

Radius

B

CACD240

1"

1/8"

9/16"

5/16"

1"

-

 

 

 

 

 

 

 

 

 

 

 

Let me know what they say

 

Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sun, Aug 4, 2019 at 3:11 AM karkauai via Groups.Io <karkauai= yahoo.com@groups.io> wrote:

 

 

Here’s the site I was looking at.  These are truly half-round with base 1”, height 1/2”(not 1”).

 

 

I’ll contact them and Steve’s site to see if I can find 1” x 1” high D profile in neoprene.

Kent Robertson

S/V Kristy

USA cell: 828-234-6819


On Aug 3, 2019, at 10:42, CW Bill Rouse < brouse@...> wrote:

Steve, 

 

Note that Trim-LOC says it uses EPDM Rubber. 

 

EPDM is related to polyethylene...I assume that this will be similar to polyfoam. The specs state that "compression Rating Recommended 25% compression for the maximum performance." This is where I had a failure with the gasket I previously used. If you notice the weight of the engine room hatch, it will compress the D Gasket to more than 25%, especially if the center hole is large.

 

Maybe the one that Kent found with a 3/16" hole will be the best.

 

 

It will take about 90' to do everything.




Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sat, Aug 3, 2019 at 1:34 PM Stephen Davis < flyboyscd@...> wrote:

Hi Bill,

 

How does this product look using the BT Tape?  

 

 

Regards,

Steve

Aloha SM72

 

 

 

 

 

Re: [Amel Yacht Owners] Bow locker seals

karkauai
 

I ordered from Amel, I haven’t received it yet, but Maud had several kinds.  I described what was originally installed and she said she’d send what appears to be the same.  It’s a D with all the walls the same, about 5mm thick all the way.  She didn’t know anything about the cylindrical piece that was described as placed into the D seals at the corners, and said they don’t have anything like that.

When I get it, I’ll take some pics and try to describe the material and compressibility.

Kent Robertson
S/V Kristy
SM243

On Sep 12, 2019, at 8:38 PM, eric freedman <kimberlite@...> wrote:

Hi Kent,

What gasket did you find for this job?

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of CW Bill Rouse
Sent: Sunday, August 04, 2019 4:10 PM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] [Amel Yacht Owners] Bow locker seals

 

Danny I am sure A represents what Amel installed, but since apparently all manufacturers have cheapened the foam by lowering the density. This is the reason that I believe I would replace it with B profile. 

 

That said, I will wait for a final judgement until after Kent has talked to the manufacturer.

 

Kent, you should ask: Is B better than A in situations where the compression will be greater than 25%. 

Best,

CW Bill Rouse
Yacht School - Supporting Amel Owners
www.YachtSchool.us
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970

 

On Sun, Aug 4, 2019, 2:23 PM Danny and Yvonne SIMMS <simms@...> wrote:

I would think A is closest to what I have on Ocean Pearl

Regards

Danny

SM 299

Ocen Pearl

On 05 August 2019 at 04:47 CW Bill Rouse <brouse@...> wrote:

I am resending this because the first email did not really look correct with HTML

 

 

 


A

B

C

D

E

R

Figure
Letter
(See Above)

CATALOG
NUMBER

Base Width

Wall

Open Height

Base T

Total Height

Radius

B

CACD240

1"

1/8"

9/16"

5/16"

1"

-

 

 

 

 

 

 

 

 

 

 

 

http://www.acmerubber.com/round.htm

 

 

 

 

Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sun, Aug 4, 2019 at 11:41 AM CW Bill Rouse via Groups.Io <brouse= gmail.com@groups.io> wrote:

Kent,

 

If I am not mistaken, they have exactly what I think will work best, which is CACD240:

 

 

 


A

B

C

D

E

R

Figure
Letter
(See Above)

CATALOG
NUMBER

Base Width

Wall

Open Height

Base T

Total Height

Radius

B

CACD240

1"

1/8"

9/16"

5/16"

1"

-

 

 

 

 

 

 

 

 

 

 

 

Let me know what they say

 

Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sun, Aug 4, 2019 at 3:11 AM karkauai via Groups.Io <karkauai= yahoo.com@groups.io> wrote:

 

 

Here’s the site I was looking at.  These are truly half-round with base 1”, height 1/2”(not 1”).

 

 

I’ll contact them and Steve’s site to see if I can find 1” x 1” high D profile in neoprene.

Kent Robertson

S/V Kristy

USA cell: 828-234-6819


On Aug 3, 2019, at 10:42, CW Bill Rouse < brouse@...> wrote:

Steve, 

 

Note that Trim-LOC says it uses EPDM Rubber. 

 

EPDM is related to polyethylene...I assume that this will be similar to polyfoam. The specs state that "compression Rating Recommended 25% compression for the maximum performance." This is where I had a failure with the gasket I previously used. If you notice the weight of the engine room hatch, it will compress the D Gasket to more than 25%, especially if the center hole is large.

 

Maybe the one that Kent found with a 3/16" hole will be the best.

 

 

It will take about 90' to do everything.



Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sat, Aug 3, 2019 at 1:34 PM Stephen Davis < flyboyscd@...> wrote:

Hi Bill,

 

How does this product look using the BT Tape?  

 

 

Regards,

Steve

Aloha SM72

 

 

 

 

 

Re: [Amel Yacht Owners] Bow locker seals

eric freedman
 

Hi Kent,

What gasket did you find for this job?

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of CW Bill Rouse
Sent: Sunday, August 04, 2019 4:10 PM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] [Amel Yacht Owners] Bow locker seals

 

Danny I am sure A represents what Amel installed, but since apparently all manufacturers have cheapened the foam by lowering the density. This is the reason that I believe I would replace it with B profile. 

 

That said, I will wait for a final judgement until after Kent has talked to the manufacturer.

 

Kent, you should ask: Is B better than A in situations where the compression will be greater than 25%. 

Best,

CW Bill Rouse
Yacht School - Supporting Amel Owners
www.YachtSchool.us
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970

 

On Sun, Aug 4, 2019, 2:23 PM Danny and Yvonne SIMMS <simms@...> wrote:

I would think A is closest to what I have on Ocean Pearl

Regards

Danny

SM 299

Ocen Pearl

On 05 August 2019 at 04:47 CW Bill Rouse <brouse@...> wrote:

I am resending this because the first email did not really look correct with HTML

 

 

 


A

B

C

D

E

R

Figure
Letter
(See Above)

CATALOG
NUMBER

Base Width

Wall

Open Height

Base T

Total Height

Radius

B

CACD240

1"

1/8"

9/16"

5/16"

1"

-

 

 

 

 

 

 

 

 

 

 

 

http://www.acmerubber.com/round.htm

 

 

 

 

Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sun, Aug 4, 2019 at 11:41 AM CW Bill Rouse via Groups.Io <brouse= gmail.com@groups.io> wrote:

Kent,

 

If I am not mistaken, they have exactly what I think will work best, which is CACD240:

 

 

 


A

B

C

D

E

R

Figure
Letter
(See Above)

CATALOG
NUMBER

Base Width

Wall

Open Height

Base T

Total Height

Radius

B

CACD240

1"

1/8"

9/16"

5/16"

1"

-

 

 

 

 

 

 

 

 

 

 

 

Let me know what they say

 

Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sun, Aug 4, 2019 at 3:11 AM karkauai via Groups.Io <karkauai= yahoo.com@groups.io> wrote:

 

 

Here’s the site I was looking at.  These are truly half-round with base 1”, height 1/2”(not 1”).

 

 

I’ll contact them and Steve’s site to see if I can find 1” x 1” high D profile in neoprene.

Kent Robertson

S/V Kristy

USA cell: 828-234-6819


On Aug 3, 2019, at 10:42, CW Bill Rouse < brouse@...> wrote:

Steve, 

 

Note that Trim-LOC says it uses EPDM Rubber. 

 

EPDM is related to polyethylene...I assume that this will be similar to polyfoam. The specs state that "compression Rating Recommended 25% compression for the maximum performance." This is where I had a failure with the gasket I previously used. If you notice the weight of the engine room hatch, it will compress the D Gasket to more than 25%, especially if the center hole is large.

 

Maybe the one that Kent found with a 3/16" hole will be the best.

 

 

It will take about 90' to do everything.



Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Sat, Aug 3, 2019 at 1:34 PM Stephen Davis < flyboyscd@...> wrote:

Hi Bill,

 

How does this product look using the BT Tape?  

 

 

Regards,

Steve

Aloha SM72

 

 

 

 

 

Re: Marina ZZ bilge pump maintenance kit

eric freedman
 

Hi,

There are a number of insertion rubbers available made of different rubbers.

What type did you use? What thickness did you use for the diaphragm and the flapper valves?

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Danny and Yvonne SIMMS
Sent: Wednesday, September 11, 2019 11:45 PM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Marina ZZ bilge pump maintenance kit

 

Hi, in the absence of a kit to hand  I made copies of the flap valves out of thick insertion rubber. This a fibre reinforced rubber sheet. I found the replacements tended to take a curve and not seal well. I got about 5 years out of the ones I made. I have just installed a new diaphragm I made out of a suitable thickness insertion rubber sheet. I punched the centre hole, put it on the shaft, closed the pump on to it, held it there while I drilled the holes. Then bolted it up and trimmed around to outer size. Working well. I made a second while I was at it to put in spares. I have been carrying the insertion rubber sheet as spare for some years. If I get premature failure (which I doubt) Ill buy the replacement 

I could have bought one first up  but I enjoy the process.

Cruising again at last. At Volivoli, Viti Vevu Fiji. Had two magnificent dives with Wananuva dive this morning. Wow.

Danny

SM299

Ocean pearl

Regards

Danny

On 12 September 2019 at 07:55 Roque <ediroque@...> wrote:

Alan

 

I recently bought from Amel. The rubber valve is a reinforced new version ( see pic)

 

1 [03028] KIT POMPE MARINA ZZ 219424/ Electric bilge pump repair kit  E$124,60 plus VAT
2 [03219] CLAPET ASPIRATION POMPE HENDERSON 72621/ Rubber valve for electric bilge pump E$17,42 each  34,84 plus VAT

 

Rgds

 

Roque

Attika A54 117

Paraty

 

Em qua, 11 de set de 2019 às 16:46, CW Bill Rouse < brouse@...> escreveu:

Amel - sav@... recently had them for the Marina ZZ

TF Marine makes an identical pump. It is either number TM-50 or TM-70...not sure. I cannot tell you where to find TF Marine spares, except at Amel...Amel replaced the reya pump with TF Marine.

 

Best,

 

CW Bill Rouse

720 Winnie St

Galveston Island, TX 77550

+1(832) 380-4970

 

 

On Wed, Sep 11, 2019 at 2:33 PM Alan Grayson < bazgrayson@...> wrote:

Hi All, Does anyone know where to get the rebuild kits for the Reya Marina ZZ bilge pump. I got on the Reya website but if my translation is right they do not sell to individuals and a google search under their part numbers has not turned up any suppliers.
Regards
Alan Grayson
SM 406 Ora Pai
St Michaels, MD

 

 

 

 

Dishwasher top loading

Paul Brown
 

hello all, I’m wanting to install a top loading dishwasher back into the counter space of my 55 and would like to know what is the best model and the experience that other owners have had with the installation and reliability, your assistance would be very much appreciated please?

the previous owner had the original machine removed due to unreliability I believe after 4 years of use 

kind regards Paul - Fortuna II 55/17

Re: AMEL 55 -2012 — Replacing CLIMA aircon unit systems with a schiller central unit

Paul Brown
 

I had too CLIMA units that were noisey which was only the fan unit vibrating and rattling, I used some gentle persuading to some areas of the frame which stopped the issue, they all run acceptably quiet now

Regards Paul - Fortuna II A55/17




On 11 Sep 2019, at 11:19 pm, CW Bill Rouse <brouse@...> wrote:

Jose,

It is at least a very big job, and possibly almost impossible job. 

The size of the remote chiller blower unit is smaller than a typical drop-in Climma Compact unit, and the saltwater condenser plumbing throughout the 55 does not exist. It is only in the engine room.

I recommend that you exhaust other means of sound reduction. I have been on several 55s and I did not notice loud sounds...maybe something is wrong.

I hope this helps.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Sep 11, 2019 at 4:13 PM Jose Alegria <Josealegr@...> wrote:
The CLIMA® unit systems of my Amell 55 - 2012 are inefficient and very noisy.
Someone in the group has experience with replacing to a  central schiller system.
All imputes are welcome

Re: Marina ZZ bilge pump maintenance kit

Danny and Yvonne SIMMS
 

Hi, in the absence of a kit to hand  I made copies of the flap valves out of thick insertion rubber. This a fibre reinforced rubber sheet. I found the replacements tended to take a curve and not seal well. I got about 5 years out of the ones I made. I have just installed a new diaphragm I made out of a suitable thickness insertion rubber sheet. I punched the centre hole, put it on the shaft, closed the pump on to it, held it there while I drilled the holes. Then bolted it up and trimmed around to outer size. Working well. I made a second while I was at it to put in spares. I have been carrying the insertion rubber sheet as spare for some years. If I get premature failure (which I doubt) Ill buy the replacement 

I could have bought one first up  but I enjoy the process.

Cruising again at last. At Volivoli, Viti Vevu Fiji. Had two magnificent dives with Wananuva dive this morning. Wow.

Danny

SM299

Ocean pearl

Regards

Danny

On 12 September 2019 at 07:55 Roque <ediroque@...> wrote:

Alan

I recently bought from Amel. The rubber valve is a reinforced new version ( see pic)

1 [03028] KIT POMPE MARINA ZZ 219424/ Electric bilge pump repair kit  E$124,60 plus VAT
2 [03219] CLAPET ASPIRATION POMPE HENDERSON 72621/ Rubber valve for electric bilge pump E$17,42 each  34,84 plus VAT

Rgds

Roque
Attika A54 117
Paraty

Em qua, 11 de set de 2019 às 16:46, CW Bill Rouse < brouse@...> escreveu:
Amel - sav@... recently had them for the Marina ZZ
TF Marine makes an identical pump. It is either number TM-50 or TM-70...not sure. I cannot tell you where to find TF Marine spares, except at Amel...Amel replaced the reya pump with TF Marine.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Sep 11, 2019 at 2:33 PM Alan Grayson < bazgrayson@...> wrote:
Hi All, Does anyone know where to get the rebuild kits for the Reya Marina ZZ bilge pump. I got on the Reya website but if my translation is right they do not sell to individuals and a google search under their part numbers has not turned up any suppliers.
Regards
Alan Grayson
SM 406 Ora Pai
St Michaels, MD

 

 

 

 

Re: AMEL 55 -2012 — Replacing CLIMA aircon unit systems with a schiller central unit

 

Jose,

It is at least a very big job, and possibly almost impossible job. 

The size of the remote chiller blower unit is smaller than a typical drop-in Climma Compact unit, and the saltwater condenser plumbing throughout the 55 does not exist. It is only in the engine room.

I recommend that you exhaust other means of sound reduction. I have been on several 55s and I did not notice loud sounds...maybe something is wrong.

I hope this helps.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Sep 11, 2019 at 4:13 PM Jose Alegria <Josealegr@...> wrote:
The CLIMA® unit systems of my Amell 55 - 2012 are inefficient and very noisy.
Someone in the group has experience with replacing to a  central schiller system.
All imputes are welcome

AMEL 55 -2012 — Replacing CLIMA aircon unit systems with a schiller central unit

Jose Alegria
 

The CLIMA® unit systems of my Amell 55 - 2012 are inefficient and very noisy.
Someone in the group has experience with replacing to a  central schiller system.
All imputes are welcome

Re: Marina ZZ bilge pump maintenance kit

Alan Grayson
 

Perfect, thank you
Alan
From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> on behalf of Roque <ediroque@...>
Sent: Wednesday, 11 September 2019 7:55:41 PM
To: main@amelyachtowners.groups.io <main@amelyachtowners.groups.io>
Subject: Re: [AmelYachtOwners] Marina ZZ bilge pump maintenance kit
 
Alan

I recently bought from Amel. The rubber valve is a reinforced new version ( see pic)

1 [03028] KIT POMPE MARINA ZZ 219424/ Electric bilge pump repair kit  E$124,60 plus VAT
2 [03219] CLAPET ASPIRATION POMPE HENDERSON 72621/ Rubber valve for electric bilge pump E$17,42 each  34,84 plus VAT

Rgds

Roque
Attika A54 117
Paraty

Em qua, 11 de set de 2019 às 16:46, CW Bill Rouse <brouse@...> escreveu:

Amel - sav@... recently had them for the Marina ZZ
TF Marine makes an identical pump. It is either number TM-50 or TM-70...not sure. I cannot tell you where to find TF Marine spares, except at Amel...Amel replaced the reya pump with TF Marine.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Sep 11, 2019 at 2:33 PM Alan Grayson <bazgrayson@...> wrote:
Hi All, Does anyone know where to get the rebuild kits for the Reya Marina ZZ bilge pump. I got on the Reya website but if my translation is right they do not sell to individuals and a google search under their part numbers has not turned up any suppliers.
Regards
Alan Grayson
SM 406 Ora Pai
St Michaels, MD

Re: Marina ZZ bilge pump maintenance kit

Roque
 

Alan

I recently bought from Amel. The rubber valve is a reinforced new version ( see pic)

1 [03028] KIT POMPE MARINA ZZ 219424/ Electric bilge pump repair kit  E$124,60 plus VAT
2 [03219] CLAPET ASPIRATION POMPE HENDERSON 72621/ Rubber valve for electric bilge pump E$17,42 each  34,84 plus VAT

Rgds

Roque
Attika A54 117
Paraty

Em qua, 11 de set de 2019 às 16:46, CW Bill Rouse <brouse@...> escreveu:

Amel - sav@... recently had them for the Marina ZZ
TF Marine makes an identical pump. It is either number TM-50 or TM-70...not sure. I cannot tell you where to find TF Marine spares, except at Amel...Amel replaced the reya pump with TF Marine.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Sep 11, 2019 at 2:33 PM Alan Grayson <bazgrayson@...> wrote:
Hi All, Does anyone know where to get the rebuild kits for the Reya Marina ZZ bilge pump. I got on the Reya website but if my translation is right they do not sell to individuals and a google search under their part numbers has not turned up any suppliers.
Regards
Alan Grayson
SM 406 Ora Pai
St Michaels, MD

Re: Marina ZZ bilge pump maintenance kit

 

Amel - sav@... recently had them for the Marina ZZ
TF Marine makes an identical pump. It is either number TM-50 or TM-70...not sure. I cannot tell you where to find TF Marine spares, except at Amel...Amel replaced the reya pump with TF Marine.

Best,

CW Bill Rouse
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970



On Wed, Sep 11, 2019 at 2:33 PM Alan Grayson <bazgrayson@...> wrote:
Hi All, Does anyone know where to get the rebuild kits for the Reya Marina ZZ bilge pump. I got on the Reya website but if my translation is right they do not sell to individuals and a google search under their part numbers has not turned up any suppliers.
Regards
Alan Grayson
SM 406 Ora Pai
St Michaels, MD

Marina ZZ bilge pump maintenance kit

Alan Grayson
 

Hi All, Does anyone know where to get the rebuild kits for the Reya Marina ZZ bilge pump. I got on the Reya website but if my translation is right they do not sell to individuals and a google search under their part numbers has not turned up any suppliers.
Regards
Alan Grayson
SM 406 Ora Pai
St Michaels, MD