Date   

Re: Engine Water leackage

Santorin LO
 

As bitter as as can...

However, Mechanic suggested leak from fresh water pump (must be right as leakage is from the back (under the timing) + leakage from oil gasket in the same area - made a lot of sense as both are coming from there.

On Thursday, October 24, 2019, 06:14:50 PM GMT+3, Bernd Spanner <bernd.spanner@...> wrote:


I had a similar colored liquid in my bilge. after a long search it turned out to be the red gear box oil mixed with diesel. reason was leaking gearbox and leaking diesel hp pump. fixed both and all is fine now.
you might also want to check on the heat exchanger lines if everything is tightened properly.
what does the liquid smell / taste like?
--
Bernd
SN 119 / Cascais, Portugal


Re: tb/BRISBANE area marina & yard/AYOG

Teun BAAS
 

Hi Matt,

 

Thanks for the suggestion but, in all honesty, except for this forum I avoid any social media as I am looking for qualified advice 😊.

 

Have gotten real, real helpful feedback so far and it worked. I think I am all covered by now thanks to this Forum.

 

Best Regards Teun

SV AMELIT  A54  #128

 

NOUMEA  NEW CALEDONIA

October 25, 2019 16:22:09

 

 

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Matt Salatino via Groups.Io
Sent: Thursday, October 24, 2019 22:54
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] tb/BRISBANE area marina & yard/AYOG

 

Try asking on the Sailing Australia FB page.....

~~~⛵️~~~Matt


On Oct 24, 2019, at 5:24 AM, Teun BAAS <teun@...> wrote:

I am leaving around November 10 2019 from NOUMEA to AUSTRALIA; probably north of BRISBANE and south of BUNDABERG.

 

Can anybody recommend a safe & affordable marina where I can leave the boat for 8 weeks or so (Dec 12, 2019 thru Feb 12, 2020) and then have her, in the vicinity, hauled out for copper coat anti-fouling plus additional 2 yearly A54 maintenance. One of my previous AUSSIE crew, living in the area, is suggesting leaving her on anchor as it is free but I prefer a slip or on the hard while I am in USA.

 

Somebody here in NOUMEA suggested MOOLOOLABA QLD – I have no clue 😊

 

I am flying out of & back in (with a lot of luggage) BRISBANE so will need to have access to transportation to & from International Airport.

 

Any yards; trades people in the area familiar with AMEL?

 

Appreciate your help & suggestions.

 

Best Regards Teun

SV AMELIT  A54  #128

 

NOUMEA  NEW CALEDONIA

October 24, 2019 20:23:20

 

 

 

 

 


Re: tb/BRISBANE area marina & yard/AYOG

Teun BAAS
 

Hi Dean,

 

Sydney – very possible but not before I have done maintenance & back in the water next year.

 

Would really like meeting and discussing our boats 😊.

 

Best Regards Teun

SV AMELIT  A54  #128

 

NOUMEA  NEW CALEDONIA

October 25, 2019 14:35:13

 

 

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of SY STELLA via Groups.Io
Sent: Friday, October 25, 2019 14:33
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] tb/BRISBANE area marina & yard/AYOG

 

Hi Tuen,
Let me know if you are coming to Sydney and we can have a meet-up. I considered buying your boat in 2017!
cheers
Dean
SY Stella
A54-154


Re: tb/BRISBANE area marina & yard/AYOG

Dean Gillies
 

Hi Tuen,
Let me know if you are coming to Sydney and we can have a meet-up. I considered buying your boat in 2017!
cheers
Dean
SY Stella
A54-154


Re: Yanmar Diesel Won't Stay Running

Chad & Leslie Shoaf
 

Had this happen with a clogged vet line. Wasps and other things build nest in them. Creates a vacuum in the fuel tank.

Chad

On Thu, Oct 24, 2019, 8:37 AM Mark Garver via Groups.Io <mgarver=me.com@groups.io> wrote:
It's been several months since my wife and I left our boat up in the Chesapeake and upon arrival today to have it hauled for a long over due cleaning. The Yanmar diesel fired right up, but then after a couple of minutes dies. Wait a couple of minutes and it fires right up again, runs for a couple of minutes and shuts off. It runs smoothly and fires up instantly so it doesn't sound like she's starving for fuel or air. The engine only has 30 hours and has be very reliable.

Any ideas?

Thanks,

Mark
S/V It's Good
SM #105


Re: Latest RigRite.com Goiot Tradition Prices 2019!

Charles Bell
 

Hello Andrew,

I agree!

The part is called an Axel bolt and I already have a batch of 100, along with other parts CNC cut in Aluminum and Anodized.

They should be back to me in a few weeks... I will be happy to hook you (and anyone else who wants some) up. I think they are costing me a couple of dollars each.

I also had the shop make the knobs (male and female)

Feel free to reach out to me if you would like a few of them. If the response is strong, I can increase the order size.


Charles
SV Jupiter


Re: Remote two way valve for flushing the water maker

Alan Leslie
 

Oh and I should have said the 24VDC timer also sends 24VDC to a relay which switches power to the FW pump so you don;t need to leave the boat with FW pump switch on. The relay and a circuit breaker for the pump supply are mounted in the circuit breaker box for the watermaker etc on the engine room forward wall.
Cheers
Alan
Elyse SM437


Re: Remote two way valve for flushing the water maker

Alan Leslie
 

Hi Paul,
I bought two 24V DC Solenoid valves on Ebay, one NO the other NC. The NO valve is in the saltwater feed line and the NC Valve replaces the manual flush valve and feeds fresh water through a TEE into the filter housing. The bottom of the 3 connectors on the TEE has the NO solenoid for saltwater supply connected to it.
The solenoid valves are wired to a small 24VDC digital timer, also from Ebay which is ,mounted in the cupboard space above the sink. The timer has 3 functions OFF, MANUAL, AUTO. When away from the boat, we ensure the water tank is full and the timer is set to Auto to flush for two minutes at 1000 Mon, Wed, Friday. It only uses about 4-5 litres each flush.
The whole set up probably cost less than $100.
Cheers
Alan
Elyse SM437  


Re: Remote two way valve for flushing the water maker

David Wallace
 

Paul, I bought two ss 12v solenoid water valves on eBay, one normally open, one normally closed. If I remember correctly they were about $50 each. Unpowered feeds saltwater to the RO, powered feeds freshwater from the tank. Ran wires to the companionway area with a single switch. The switch is wired through the RO on/off power switch so the solenoids can’t be switched unless the system is running. It’s worked well for 9 years now.

Dave Wallace
s/v Air Ops
Maramu #104

On Oct 24, 2019, at 1:14 PM, Paul Osterberg <osterberg.paul.l@...> wrote:

I found this two way valve to make it possible to flush the water maker without going down to the engine room. A bit expensive 450 €. anyone know a cheaper solution.  Yrs I know open the hatch and go down the engine room is a cheaper solution but I'm looking for a remote controlled way to flush the water-maker

Paul SY Kerpa SM#259 Lagos <2 way valve.PNG>


Re: Yanmar Diesel Won't Stay Running

 

typo: should have been "normally open electromagnetic valve"


--
CW Bill Rouse Amel Yacht Owners School
Address: 720 Winnie, Galveston Island, Texas 77550 
   


On Thu, Oct 24, 2019 at 5:39 PM CW Bill Rouse via Groups.Io <brouse=gmail.com@groups.io> wrote:
I have been following this thread. While I agree that it is a fuel issue, don't forget about the normally closed electromagnetic fuel cutoff valve. Maybe you have a poor connection with the off button, relay, or cutoff valve.

Good luck. 

Best,

CW Bill Rouse
Amel Yacht Owners School - www.AmelYachtOwnersSchool.com
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970

On Thu, Oct 24, 2019, 5:22 PM Mark Erdos <mcerdos@...> wrote:

Mark,

 

Sorry not on the boat right now but I seem to remember on the Yanmar the fuel filter has a drain on the bottom. You could sample your diesel from there and put it into a glass container. Let it sit and look for separation.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Vista Mar, Panama

www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Garver via Groups.Io
Sent: Thursday, October 24, 2019 11:57 AM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Yanmar Diesel Won't Stay Running

 

Mark,

 

Unfortunately not. But I think I can put a hose in the bottom of the tank and pump some out to see. At least that is the current plan as well as ensuring the filter is clean.

 

Thanks,

 

Mark

S/V It's Good

SM #105


On October 24, 2019 at 10:30 AM, Mark Erdos <mcerdos@...> wrote:

Mark,

 

You have a fuel problem. Do you have a filtration system that allows you to check for water?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Vista Mar, Panama

http://www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Garver via Groups.Io
Sent: Thursday, October 24, 2019 8:37 AM
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Yanmar Diesel Won't Stay Running

 

It's been several months since my wife and I left our boat up in the Chesapeake and upon arrival today to have it hauled for a long over due cleaning. The Yanmar diesel fired right up, but then after a couple of minutes dies. Wait a couple of minutes and it fires right up again, runs for a couple of minutes and shuts off. It runs smoothly and fires up instantly so it doesn't sound like she's starving for fuel or air. The engine only has 30 hours and has be very reliable.

 

Any ideas?

 

Thanks,

 

Mark

S/V It's Good

SM #105

 

 

 

 


Re: Yanmar Diesel Won't Stay Running

 

I have been following this thread. While I agree that it is a fuel issue, don't forget about the normally closed electromagnetic fuel cutoff valve. Maybe you have a poor connection with the off button, relay, or cutoff valve.

Good luck. 

Best,

CW Bill Rouse
Amel Yacht Owners School - www.AmelYachtOwnersSchool.com
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970


On Thu, Oct 24, 2019, 5:22 PM Mark Erdos <mcerdos@...> wrote:

Mark,

 

Sorry not on the boat right now but I seem to remember on the Yanmar the fuel filter has a drain on the bottom. You could sample your diesel from there and put it into a glass container. Let it sit and look for separation.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Vista Mar, Panama

www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Garver via Groups.Io
Sent: Thursday, October 24, 2019 11:57 AM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Yanmar Diesel Won't Stay Running

 

Mark,

 

Unfortunately not. But I think I can put a hose in the bottom of the tank and pump some out to see. At least that is the current plan as well as ensuring the filter is clean.

 

Thanks,

 

Mark

S/V It's Good

SM #105


On October 24, 2019 at 10:30 AM, Mark Erdos <mcerdos@...> wrote:

Mark,

 

You have a fuel problem. Do you have a filtration system that allows you to check for water?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Vista Mar, Panama

http://www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Garver via Groups.Io
Sent: Thursday, October 24, 2019 8:37 AM
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Yanmar Diesel Won't Stay Running

 

It's been several months since my wife and I left our boat up in the Chesapeake and upon arrival today to have it hauled for a long over due cleaning. The Yanmar diesel fired right up, but then after a couple of minutes dies. Wait a couple of minutes and it fires right up again, runs for a couple of minutes and shuts off. It runs smoothly and fires up instantly so it doesn't sound like she's starving for fuel or air. The engine only has 30 hours and has be very reliable.

 

Any ideas?

 

Thanks,

 

Mark

S/V It's Good

SM #105

 

 

 

 


Re: Yanmar Diesel Won't Stay Running

Mark Erdos
 

Mark,

 

Sorry not on the boat right now but I seem to remember on the Yanmar the fuel filter has a drain on the bottom. You could sample your diesel from there and put it into a glass container. Let it sit and look for separation.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Vista Mar, Panama

www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Garver via Groups.Io
Sent: Thursday, October 24, 2019 11:57 AM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Yanmar Diesel Won't Stay Running

 

Mark,

 

Unfortunately not. But I think I can put a hose in the bottom of the tank and pump some out to see. At least that is the current plan as well as ensuring the filter is clean.

 

Thanks,

 

Mark

S/V It's Good

SM #105


On October 24, 2019 at 10:30 AM, Mark Erdos <mcerdos@...> wrote:

Mark,

 

You have a fuel problem. Do you have a filtration system that allows you to check for water?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Vista Mar, Panama

http://www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Garver via Groups.Io
Sent: Thursday, October 24, 2019 8:37 AM
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Yanmar Diesel Won't Stay Running

 

It's been several months since my wife and I left our boat up in the Chesapeake and upon arrival today to have it hauled for a long over due cleaning. The Yanmar diesel fired right up, but then after a couple of minutes dies. Wait a couple of minutes and it fires right up again, runs for a couple of minutes and shuts off. It runs smoothly and fires up instantly so it doesn't sound like she's starving for fuel or air. The engine only has 30 hours and has be very reliable.

 

Any ideas?

 

Thanks,

 

Mark

S/V It's Good

SM #105

 

 

 

 


Re: seals orientation

Craig Briggs
 
Edited

Hello José,
While on the subject of seal orientation, some time ago (maybe 2-3 years?), you installed your prop shaft seals in a different orientation than the "Amel way".  I recall you had the three seals, from front to back (first to last when installing) with the first two facing out (open side toward the sea) and the last one facing in (open side toward oil). Your logic was great - that we're trying to keep water out and so have the maximum protection of the first two do just that, with any oil seepage giving lubrication and the outer seal stopping oil from escaping to sea.

How has that worked out - is your oil still pristine?

Great timing on getting out of a chilly Boston!
Best regards, Craig


Re: Yanmar Diesel Won't Stay Running

Mark McGovern
 

Mark,

I should have asked this question in my first post but what model Yanmar engine is it?  If its newer one with electronically controlled fuel injection via an Electronic Control Unit (ECU) than my first response is invalid as it was referring to older (all mechanical) diesel engines.   

--
Mark McGovern
SM #440 Cara
Deale, MD USA


Latest RigRite.com Goiot Tradition Prices 2019!

Andrew Eaves
 

Yes we know M stands for Marine in the industry when buying parts. 

So thanks to this site, I found what hatches are on my Euros 41 and asked RigRite for a quote for 2 skus. One they don't have but this one just impressed me. I shouldn't be too shocked but come on!

Also love the section - 'Lead time on Goi PT-HP8 @ 12 weeks'

So serious question, in my business I can produce parts such as this in titanium. I could make the pins, plastic handle, the screw above for less than these daft prices. Thoughts anyone?
Also with plastic printing being relatively cheap now, how many people need these parts or similar but hold off owing to the costs? Could organise a group purchase.

Regards

Andrew


Re: Amel Euros 41 1976 - Steering Wheel Removal Confusion

Andrew Eaves
 

Thanks to all for your replies. 

I got the wheel back on today with the play removed which was the intitial plan. I also ditched the cog and chain for the autopilot which isn't working. I can't see that being reinstated but as we do, I'll keep the parts for now.

Re the cables, I haven't checked the condition as the aft cabin is a storeroom for looming jobs. It is smooth though for now. Hydraulic no doubt the way forward, but maybe with an autopilot integration at the same time. With me being in Greece, there isn't a lot of point for autopilot, just if I venture further one day. 

Hi Elja, 'You have a verry good boat but a lot of work' - You're not kidding! Will be rewarding though :)

Thanks all.


Remote two way valve for flushing the water maker

Paul Osterberg
 

I found this two way valve to make it possible to flush the water maker without going down to the engine room. A bit expensive 450 €. anyone know a cheaper solution.  Yrs I know open the hatch and go down the engine room is a cheaper solution but I'm looking for a remote controlled way to flush the water-maker

Paul SY Kerpa SM#259 Lagos


Re: Yanmar Diesel Won't Stay Running

Mark Garver <mgarver@...>
 

The mechanic at the marina asked the same question about the auto-shutdown feature, so he's investigating that. I am about to pump some fuel from the bottom of the tank to check for water. I will also check for a vacuum on the fuel line, that's a good idea. 

Thanks!

Mark
S/V It's Good
SM #105

On October 24, 2019 at 12:58 PM, John Clark <john.biohead@...> wrote:

My first thought is also fuel supply.  One time we started our engine with the fuel shut off valve closed...she ran perfect then just quit.  I can see the engine pulling a vacuum on the fuel line stalling ...then as the vacuum leaks off being able to restart.  

Now my second thought is based on you saying it was a new engine.   Does the engine have any automatic shutdown features like the genset?  Recall the genset has a host of conditions that will cause the machine to shutdown.  Just owndering if the new engine presumably with a computer is doing something on it's own.

John
SV Annie SM37
Brunswick GA

On Thu, Oct 24, 2019 at 11:58 AM Mark Garver via Groups.Io <mgarver=icloud.com@groups.io> wrote:
Mark,

Unfortunately not. But I think I can put a hose in the bottom of the tank and pump some out to see. At least that is the current plan as well as ensuring the filter is clean.

Thanks,

Mark
S/V It's Good
SM #105

On October 24, 2019 at 10:30 AM, Mark Erdos <mcerdos@...> wrote:

Mark,

 

You have a fuel problem. Do you have a filtration system that allows you to check for water?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Vista Mar, Panama

http://www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Garver via Groups.Io
Sent: Thursday, October 24, 2019 8:37 AM
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Yanmar Diesel Won't Stay Running

 

It's been several months since my wife and I left our boat up in the Chesapeake and upon arrival today to have it hauled for a long over due cleaning. The Yanmar diesel fired right up, but then after a couple of minutes dies. Wait a couple of minutes and it fires right up again, runs for a couple of minutes and shuts off. It runs smoothly and fires up instantly so it doesn't sound like she's starving for fuel or air. The engine only has 30 hours and has be very reliable.

 

Any ideas?

 

Thanks,

 

Mark

S/V It's Good

SM #105










Re: Bow thruster seals orientation

Jose Venegas
 

David,

Yes they are intended to replace the hard lip seal. I installed them in the opposite order of your second picture but with the same orientation that you have them : Both lips facing the water.
I noted that the current seals came a little bit off in the dimensions of my first order and gluing the upper (wiper) seal to the lower (U) seal leaves a small gap in the surface of contact unless you glue them before mounting them and you place some weight on them while the permanent silicone glue is dry.
However, I think that if you mount them the way you show in the second picture there will not leave a gap and they should work OK. That is not what I did with my seals 3 years ago but I would be tempted to do it that way when, and if, I replace them with the new set.

In fact your order may result in an even better sealing action and better attachment between each other and to the fiberglass.

Jose
Ipanema SM2K 278
Finally leaving Boston towards Martinique on November 1


Re: tb/BRISBANE area marina & yard/AYOG

Teun BAAS
 

Hi Lauren & Colin,

 

Deeply appreciate your Email and I am already sending an Email to Mandy at this (early) moment. 😊

 

I will be sending you an Email with several other questions in reference to my AUSTRALIA stay.

 

How did your new sails work out?

 

Best Regards Teun

SV AMELIT  A54  #128

 

NOUMEA  NEW CALEDONIA

October 25, 2019 05:22:35

 

 

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of islandpearl2_sm2k332 via Groups.Io
Sent: Thursday, October 24, 2019 23:36
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] tb/BRISBANE area marina & yard/AYOG

 

Hi Teun

 

We have just arrived back in Australia after completing our circumnavigation this week. Right now we are in Bundaberg for a few weeks but will return home to Brisbane soon around mid-November.

 

Please do not ever consider leaving your Amel on an anchor anywhere in Brisbane. That was not good advice at all.

 

In terms of Brisbane Marinas, we choose a small fairly unknown marina called Newport Marina to berth SV island Pearl II since it is safe, within walking distance from the train to the city and airport. It is a quiet residential type marina with old, but well-kept facilities, and has plenty of car parking right near the boat. It is not a lively place with shops and restaurants, but we like it quiet and it is surrounded by nice upmarket waterfront homes on a canal system. This in our view makes it the safest marina in Brisbane if a tropical storm should ever hit, which is almost impossible. 

 

Fortunately, the prices there also very reasonable since it is not well known that the entrance channel has recently been deepened, and this was also not shown on the Navionics charts. Most cruisers would not be aware that they could get in there, but it is now at least  2m at low tide LAT, so it is easy to get your Amel in there at most times other than just an hour or two either side of absolute low tides. You can contact the Manager "Mandy" on email: info@..., or call her on and ask her if she has any free spots on D Berth facing the main channel as Island Pearl II is normally there, and am happy to keep a good eye on any Amels who berth near Island Pearl II. Unfortunately, I think there was recently only one space available, so if interested then try to contact her soon and mention me in case that helps get you in. The marina is located at 158 Griffith Road, Newport, QLD 4020... Phone: 07 3203 5855 

 

The marina/boatyard called "Laurie's Marina" in Mooloolaba is also a reasonable option, and I am aware that they did lift an Amel 53 there a few years ago, and built a nice hardtop for it, and the owner was happy with all the work they did. 

 

The other marina to consider is Scarborough Marina (very near Newport Marina) which has a fully working boatyard, however, their travel lift is a bit small, so I personally would not lift even my Amel 53 there. Contact them on +61 7 3880 0300 - website www.scarbmarina.com.au.

 

In terms of having Copper Coat work done I would firstly trust the "BOATWORKS" boatyard on the Gold Coast the most. That is where I always haul out Island Pearl II for normal antifouling paint and prop shaft / Bowthruster servicing, but I do the servicing myself and use them for the paint job. It is without any doubt the best boatyard we have come across anywhere in the world and has all the expertise and parts you could need right there. Prices are not bad too. You can contact them on admin@the boatworks.com.au or phone +61 7 55 000 000 and speak to the manager about who has the best copper coat application experience in his yard. If you have an Autoprop, there is the Australian Autoprop agent right there too who recently replaced my autoprop bearings there and did a great job.

 

Finally, Teuns, check with Boatworks about long term out of water storage for your Amel too. I have been away from Australia for 3 years now but recently heard that Boatworks now have this service too. That could be a good option for you too.

 

Best of luck with it and safe travels over to Australia

 

Colin & Lauren Streeter

Bundaberg Port Marina

 

Now that we have completed our circumnavigation, Island Pearl II is finally really for sale. Contact me direct via email for prices. She is Australian Duty and GST Paid and UK registered. 

 

 

 

 

 

 

 

 

 

On Thu, Oct 24, 2019 at 7:25 PM Teun BAAS <teun@...> wrote:

I am leaving around November 10 2019 from NOUMEA to AUSTRALIA; probably north of BRISBANE and south of BUNDABERG.

 

Can anybody recommend a safe & affordable marina where I can leave the boat for 8 weeks or so (Dec 12, 2019 thru Feb 12, 2020) and then have her, in the vicinity, hauled out for copper coat anti-fouling plus additional 2 yearly A54 maintenance. One of my previous AUSSIE crew, living in the area, is suggesting leaving her on anchor as it is free but I prefer a slip or on the hard while I am in USA.

 

Somebody here in NOUMEA suggested MOOLOOLABA QLD – I have no clue 😊

 

I am flying out of & back in (with a lot of luggage) BRISBANE so will need to have access to transportation to & from International Airport.

 

Any yards; trades people in the area familiar with AMEL?

 

Appreciate your help & suggestions.

 

Best Regards Teun

SV AMELIT  A54  #128

 

NOUMEA  NEW CALEDONIA

October 24, 2019 20:23:20

 

 

 

 

 


 

--

Colin Streeter

0411 016 445