Re: Prop to Zinc Connection
Stephan Regulinski
Bonjour Olivier, But from prop shaft to zincs on the rudder I got a range of measurements between 2 and 50 Ohms, depending on movement of the propeller. I measured 0.2 Ohms from bonding wire on the C Drive to zincs on the rudder. Any idea why this could occur? Should I do something to correct?
|
|
gel coat Nr. SM 2005
Hi All,
Does anyone knows the gel coat number of a SM 2005. We replaced the chart plotter outside and need to fill some holes. Tried to add a picture but was to big. Kindly Regards, Steven Nieman SM 476
|
|
Re: Hardellet motor reversing solenoids for mast/boom
eric freedman
I got mine from Amel. Fair Winds Eric Amel Super Maramu #376
From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Thomas Kleman
Sent: Wednesday, December 11, 2019 2:15 PM To: main@AmelYachtOwners.groups.io Subject: [AmelYachtOwners] Hardellet motor reversing solenoids for mast/boom
Does anyone have the precise product number for the mast solenoids ? I'd like to carry some as spares.
|
|
Re: vetus coupling removal
eric freedman
Hi, Here is the photo. Once you have it apart have a machine shop open up the hole a few thousands of an inch. Fair Winds Eric Amel Super Maramu #376
From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Herbert Lackner
Sent: Tuesday, December 10, 2019 11:09 PM To: main@AmelYachtOwners.groups.io Subject: [AmelYachtOwners] vetus coupling removal
today I tried to align the engine and the c-drive. unfortunately I was not able to remove the vetus coupling from the shaft, tried it also with a puller but without success. Are there any tricks, special tools,... how this can be done? I remember Eric uploaded a foto showing the tool he made for that, but could not find it. any help welcome
|
|
Re: Manuals and instructions of the Amel Sharki 1982 Nr 53.
Ralf Schroeder
Moin Gerhard,
many thanks :-) Best Ralf
|
|
Re: What is this black gasket
Patrick McAneny
Bill , Might the gasket fit over the threaded opening and rest on top of the reservoir and the cap tighten down on top of it ,I see black marks on the bottom of the cap as though it had been in contact with the rubber gasket. Not the typical gasket/cap contact point , but may be. Does the gasket fit over the threaded part of the reservoir ? The diameter looks about right .
Pat
SM Shenanigans
-----Original Message-----
From: CW Bill Rouse <brouse@...> To: main <main@amelyachtowners.groups.io> Sent: Wed, Dec 11, 2019 4:53 pm Subject: [AmelYachtOwners] What is this black gasket See the black gasket in the attached picture. It was found inside the C-drive oil reservoir. At first glance I thought it was the gasket for the top, but obviously not. It is too large.
I think I have seen this gasket before.
Any help would be appreciated.
Best,
CW Bill Rouse Amel Owners Yacht School - www.AmelOwnersYachtSchool.com 720 Winnie St Galveston Island, TX 77550 +1(832) 380-4970
|
|
Re: Maramu Gearbox identification
James Alton
Craig,
toggle quoted messageShow quoted text
I am amazed that you found a US source for these boxes! Thanks for sharing, I have added this information to my Sueno file. I will be in Florida myself pretty soon and will follow up. I agree with what you said about the cooling fins not being needed since our usage is of short duration. Thanks, James SV Sueno Maramu #220
On Dec 11, 2019, at 5:18 PM, Craig Briggs SN 68 Sangaris via Groups.Io <sangaris=aol.com@groups.io> wrote:
|
|
Re: What is this black gasket
Danny and Yvonne SIMMS
Hi Bill. I would suggest it goes under the cap. Sometimes the material used expands with age. Regards and wishing you and Judy all the best for Christmas and the new year. I hope your new career alows you some time to enjoy yourselves. Danny SM 299 Ocean Pearl
On 12 December 2019 at 10:52 CW Bill Rouse <brouse@...> wrote:
|
|
Re: Needed: Amel Experienced Surveyor - North East USA
Miles
Hi Jer,
I have used this person. He did a thorough job for me in RI. I was impressed and I recommend him.
WILLIAM COBLE Independent Marine Surveyor P.O. Box 1434 North Kingstown, Rhode Island 02852 tel/fax 401 295 1389 cobleboatsurveys@...
Miles
s/y Ladybug, sm 216 Le Marin, Martinique
|
|
Re: What is this black gasket
Porter, Yes, it doesn't fit. The gasket is too large. Best, CW Bill Rouse Amel Owners Yacht School - www.AmelOwnersYachtSchool.com 720 Winnie St Galveston Island, TX 77550 +1(832) 380-4970
On Wed, Dec 11, 2019, 3:53 PM Porter McRoberts via Groups.Io <portermcroberts=yahoo.com@groups.io> wrote:
|
|
Re: What is this black gasket
Porter McRoberts
That the lid to the c-drive oil reservoir and associated gasket.
toggle quoted messageShow quoted text
Porter iBIS 54-152 Excuse the errors. Sent from my IPhone Www.fouribis.com
On Dec 12, 2019, at 10:53 AM, CW Bill Rouse <brouse@...> wrote:
|
|
Re: What is this black gasket
Porter McRoberts
Are you sure it doesn’t fit??
toggle quoted messageShow quoted text
Pm Excuse the errors. Sent from my IPhone Www.fouribis.com
On Dec 12, 2019, at 12:52 PM, Porter McRoberts <portermcroberts@...> wrote:
|
|
Re: Hardellet motor reversing solenoids for mast/boom
Hello Thomas,
When I ordered some from Hardellet in 2015 the reference number was BDP 20000 24V Cheers Alan Elyse SM437
|
|
What is this black gasket
See the black gasket in the attached picture. It was found inside the C-drive oil reservoir. At first glance I thought it was the gasket for the top, but obviously not. It is too large. I think I have seen this gasket before. Any help would be appreciated. Best, CW Bill Rouse Amel Owners Yacht School - www.AmelOwnersYachtSchool.com 720 Winnie St Galveston Island, TX 77550 +1(832) 380-4970
|
|
Re: Maramu Gearbox identification
James,
I got mine from US Distributor: Drivetech Automation; 5401 NW 102nd Ave #146; Sunrise, FL33351 954.746.9800. They were $220 each plus tax & shipping (a few years ago). You will have to grind off some of the cooling fins on the mainsail furler to fit it inside the mast (at least on my SN). This is what AMEL did, I'm sure and it has no effect on the operation (the fins would only be needed for high speed continuous operation in an industrial application). You will need to reuse the delrin mounts and, as I recall, you need to bore a couple of holes in the cover to match the delrin block. You can add Zerk grease fittings if you wish. Good luck with it, Craig
|
|
Re: vetus coupling removal
Herbert Lackner
finally removed it. what you need is a puller, a hammer and 6 hours :-) . alignment was easy then using the tool.
santorin owners with a shaft alternator: the "special tool" should be 45 mm longer than for the SM, due to the pulley of the shaft alternator. it still works but would be better if I had made it longer. herbert
|
|
Re: “Default” anchor arrangement on an Amel 54
We have instalt in the summer the Spade 200 in Aluminium with
26 kg he works for boats by 30 Tonns and 25 m for the second Anker we by a Spade 140 In Aluminium for boats 20 Tonns and 20 m For the summer and otom time it works perfect Best Elja Röllinghoff SM Balu 222 Von meinem iPhone gesendet
|
|
Hardellet motor reversing solenoids for mast/boom
Thomas Kleman
Does anyone have the precise product number for the mast solenoids ? I'd like to carry some as spares.
Thomas Kleman SV L'ORIENT SM2K 422 Shelter Bay, Panama
|
|
Re: Maramu Gearbox identification
James Alton
Craig,
toggle quoted messageShow quoted text
Thanks a lot for the help. If there is a supplier that you like to use for ordering these please let me know. Best, James SV Sueno Maramu #220
|
|
Re: Manuals and instructions of the Amel Sharki 1982 Nr 53.
Gerhard Mueller
On Wed, Dec 11, 2019 at 04:29 PM, Ralf Schroeder wrote:
But I'm searching for a manual for the original autopilot with panel etc. myself.Here are some links for the Neco: https://topperdiek.de/dl/Amel/NECO_692_quick_start.pdf https://topperdiek.de/dl/Amel/NECO-komplet-Manual.pdf https://topperdiek.de/dl/Amel/Neco-Marine-Autopilot.pdf -- Gerhard Mueller Amel Sharki #60 Currently Kalamata, Greece
|
|