Date   

Re: Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Courtney Gorman
 

Porter there is tubing that comes out of the bottom of the unit and goes through the deck into the sail locker it serves two purposes it carries the wires for the power it also acts as the drain for the unit sometimes if this package is not stretched tight a loop is created near the Furler so water cannot drain which then allows
The break in the bottom of the Furler to rust and seize and the motor burns out


On Mar 2, 2020, at 4:22 PM, Porter McRoberts via Groups.Io <portermcroberts@...> wrote:

Courtney.  Can you please expound? Obviously you took notice of something specific.
Always appreciated.
Porter
A54-152 IBIS


On Mar 2, 2020, at 4:11 PM, Courtney Gorman via Groups.Io <Itsfun1@...> wrote:

Make sure with the Bamar that it is set up to drain properly otherwise the brake will fail and ruin the motor
Otherwise great piece of kit
Cheers
Courtney
54 #101
Trippin


-----Original Message-----
From: Teun BAAS <teun@...>
To: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io>
Sent: Mon, Mar 2, 2020 3:24 pm
Subject: Re: [AmelYachtOwners] Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Hi Stefan,
 
I have, what I believe, the 3rd generation BAMAR. This version is NOT belt driven but gear driven.
No problems at all – major improvement over the previous 2 versions.
 
Best Regards Teun
SV AMELIT  A54  #128
 
Currently on the hard in COOMERA (near BRISBANE) QLD AUSTRALIA
March 2, 2020 13:23:55
 
USA cell: +1 832 477 8842
AUSTRALIA cell: +61 5951 8909
 
You can follow AMELIT via this link: https://forecast.predictwind.com/tracking/display/AMELIT
 
 
 
From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Stefan Schaufert via Groups.Io
Sent: Monday, March 2, 2020 13:16
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Front furler Bamar MEJ upgrade to EJF? Is it worth it?
 
Dear Ameliens,
 
I consider to change the genua furler (MEJ) to the newest BAMAR model (EFJ?) - if the technic is much better then the MEJ-modell (bad engineered + belts) . There where recently 2 belts broken (within 4 weeks, after 6 month of working fine) - not nice + lot of hard work. A thing that I do not wont to have again.
Is in the new modell still a belt inside?
What is your experience?
Or is it wiser to go directly to a Reckmann?

Thanks for your responses.

Best regards
Stefan
AMEL 54 N° 119 LADY CHARLYETTE, currently Dominica


Re: Headliner fix

Paul Stascavage
 

Just an FYI. 

I’m not sure what headliner was used in the 54 or earlier models of SM’s, Maramu’s, etc., but the headliner in our boat (SM #466) was still available about a year ago. It has a felt like backing. We are looking to replace the fine plush like material that lines the forward and captains berth walls and thought the headliner would be a good replacement material as well as match the rest of the boat.  Most SM’s we have seen have the pleated cushion material in these areas and it is attached with Velcro. Ours has this thin layer of material that appears to be glued in place. We haven’t completed the project yet as I am still trying to figure out if I will be able to remove these panels first. Hopefully this summer I will find some spare time to investigate further. It does appear that there are some screws behind the fabric but I am not sure if all the mounting screws are accessible. If anyone knows please let me know. 

Slightly off topic, but if anyone is interested, at the same time we purchased some of the original blue shower curtain material and had new curtains made. Again that was available as of about a year ago. 

All the Best,

Paul Stascavage
S/V Rita Kathryn SM #466

RitaKathryn.com

Currently Cruising Bahamas


Re: Super maramu max prop

Stephen Davis
 

Hi Rob,

if you give PYI a call, they are very helpful. They will need to know your engine, type of boat, diameter of the prop, and left hand rotation. I believe the diameter is 21”, but assuming you are out of the water, you can measure to be sure. We re-powered with a Yanmar, and the pitch PYI came up with was exactly correct when we sea trialed it. 


Good luck.

Steve Davis
Aloha SM 72
Hawaii


Re: Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Porter McRoberts
 

Courtney.  Can you please expound? Obviously you took notice of something specific.
Always appreciated.
Porter
A54-152 IBIS


On Mar 2, 2020, at 4:11 PM, Courtney Gorman via Groups.Io <Itsfun1@...> wrote:

Make sure with the Bamar that it is set up to drain properly otherwise the brake will fail and ruin the motor
Otherwise great piece of kit
Cheers
Courtney
54 #101
Trippin


-----Original Message-----
From: Teun BAAS <teun@...>
To: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io>
Sent: Mon, Mar 2, 2020 3:24 pm
Subject: Re: [AmelYachtOwners] Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Hi Stefan,
 
I have, what I believe, the 3rd generation BAMAR. This version is NOT belt driven but gear driven.
No problems at all – major improvement over the previous 2 versions.
 
Best Regards Teun
SV AMELIT  A54  #128
 
Currently on the hard in COOMERA (near BRISBANE) QLD AUSTRALIA
March 2, 2020 13:23:55
 
USA cell: +1 832 477 8842
AUSTRALIA cell: +61 5951 8909
 
You can follow AMELIT via this link: https://forecast.predictwind.com/tracking/display/AMELIT
 
 
 
From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Stefan Schaufert via Groups.Io
Sent: Monday, March 2, 2020 13:16
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Front furler Bamar MEJ upgrade to EJF? Is it worth it?
 
Dear Ameliens,
 
I consider to change the genua furler (MEJ) to the newest BAMAR model (EFJ?) - if the technic is much better then the MEJ-modell (bad engineered + belts) . There where recently 2 belts broken (within 4 weeks, after 6 month of working fine) - not nice + lot of hard work. A thing that I do not wont to have again.
Is in the new modell still a belt inside?
What is your experience?
Or is it wiser to go directly to a Reckmann?

Thanks for your responses.

Best regards
Stefan
AMEL 54 N° 119 LADY CHARLYETTE, currently Dominica


Re: Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Courtney Gorman
 

Make sure with the Bamar that it is set up to drain properly otherwise the brake will fail and ruin the motor
Otherwise great piece of kit
Cheers
Courtney
54 #101
Trippin


-----Original Message-----
From: Teun BAAS <teun@...>
To: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io>
Sent: Mon, Mar 2, 2020 3:24 pm
Subject: Re: [AmelYachtOwners] Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Hi Stefan,
 
I have, what I believe, the 3rd generation BAMAR. This version is NOT belt driven but gear driven.
No problems at all – major improvement over the previous 2 versions.
 
Best Regards Teun
SV AMELIT  A54  #128
 
Currently on the hard in COOMERA (near BRISBANE) QLD AUSTRALIA
March 2, 2020 13:23:55
 
USA cell: +1 832 477 8842
AUSTRALIA cell: +61 5951 8909
 
 
 
 
From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Stefan Schaufert via Groups.Io
Sent: Monday, March 2, 2020 13:16
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Front furler Bamar MEJ upgrade to EJF? Is it worth it?
 
Dear Ameliens,
 
I consider to change the genua furler (MEJ) to the newest BAMAR model (EFJ?) - if the technic is much better then the MEJ-modell (bad engineered + belts) . There where recently 2 belts broken (within 4 weeks, after 6 month of working fine) - not nice + lot of hard work. A thing that I do not wont to have again.
Is in the new modell still a belt inside?
What is your experience?
Or is it wiser to go directly to a Reckmann?

Thanks for your responses.

Best regards
Stefan
AMEL 54 N° 119 LADY CHARLYETTE, currently Dominica


Re: Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Teun BAAS
 

Further to Porter’s review below – or the connection between the EJF and the aluminum furler.

 

I checked RECKMANN before ordering the 3rd set of BAMAR’s but the price difference was extreme.

 

Best Regards Teun

SV AMELIT  A54  #128

 

currently on the hard in COOMERA (near BRISBANE) QLD AUSTRALIA

March 2, 2020 13:40:44

 

USA cell: +1 832 477 8842

AUSTRALIA cell: +61 5951 8909

 

You can follow AMELIT via this link: https://forecast.predictwind.com/tracking/display/AMELIT

 

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Porter McRoberts via Groups.Io
Sent: Monday, March 2, 2020 13:36
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Front furler Bamar MEJ upgrade to EJF? Is it worth it?

 

The EJF is fantastic.  Flawless operation and a pleasure to use.

No belt.  One just has to be careful, whereas the weakest link in the MEJ was the belt, the weakest link in the EJF may now be the deck hardware!  

A reckmann seems fine too, but were very happy with the EJFs after 15k+miles.

Porter

A54-152 IBIS



On Mar 2, 2020, at 3:15 PM, Stefan Schaufert <mail@...> wrote:

 

Dear Ameliens,

 

I consider to change the genua furler (MEJ) to the newest BAMAR model (EFJ?) - if the technic is much better then the MEJ-modell (bad engineered + belts) . There where recently 2 belts broken (within 4 weeks, after 6 month of working fine) - not nice + lot of hard work. A thing that I do not wont to have again.

Is in the new modell still a belt inside?

What is your experience?

Or is it wiser to go directly to a Reckmann?

Thanks for your responses.

Best regards
Stefan
AMEL 54 N° 119 LADY CHARLYETTE, currently Dominica

 


Re: Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Porter McRoberts
 

The EJF is fantastic.  Flawless operation and a pleasure to use.
No belt.  One just has to be careful, whereas the weakest link in the MEJ was the belt, the weakest link in the EJF may now be the deck hardware!  
A reckmann seems fine too, but were very happy with the EJFs after 15k+miles.
Porter
A54-152 IBIS

On Mar 2, 2020, at 3:15 PM, Stefan Schaufert <mail@...> wrote:

Dear Ameliens,

 

I consider to change the genua furler (MEJ) to the newest BAMAR model (EFJ?) - if the technic is much better then the MEJ-modell (bad engineered + belts) . There where recently 2 belts broken (within 4 weeks, after 6 month of working fine) - not nice + lot of hard work. A thing that I do not wont to have again.

Is in the new modell still a belt inside?

What is your experience?

Or is it wiser to go directly to a Reckmann?

Thanks for your responses.

Best regards
Stefan
AMEL 54 N° 119 LADY CHARLYETTE, currently Dominica



Re: Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Teun BAAS
 

Hi Stefan,

 

I have, what I believe, the 3rd generation BAMAR. This version is NOT belt driven but gear driven.

No problems at all – major improvement over the previous 2 versions.

 

Best Regards Teun

SV AMELIT  A54  #128

 

Currently on the hard in COOMERA (near BRISBANE) QLD AUSTRALIA

March 2, 2020 13:23:55

 

USA cell: +1 832 477 8842

AUSTRALIA cell: +61 5951 8909

 

You can follow AMELIT via this link: https://forecast.predictwind.com/tracking/display/AMELIT

 

 

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Stefan Schaufert via Groups.Io
Sent: Monday, March 2, 2020 13:16
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Front furler Bamar MEJ upgrade to EJF? Is it worth it?

 

Dear Ameliens,

 

I consider to change the genua furler (MEJ) to the newest BAMAR model (EFJ?) - if the technic is much better then the MEJ-modell (bad engineered + belts) . There where recently 2 belts broken (within 4 weeks, after 6 month of working fine) - not nice + lot of hard work. A thing that I do not wont to have again.

Is in the new modell still a belt inside?

What is your experience?

Or is it wiser to go directly to a Reckmann?

Thanks for your responses.

Best regards
Stefan
AMEL 54 N° 119 LADY CHARLYETTE, currently Dominica


Front furler Bamar MEJ upgrade to EJF? Is it worth it?

Stefan Schaufert
 

Dear Ameliens,

 

I consider to change the genua furler (MEJ) to the newest BAMAR model (EFJ?) - if the technic is much better then the MEJ-modell (bad engineered + belts) . There where recently 2 belts broken (within 4 weeks, after 6 month of working fine) - not nice + lot of hard work. A thing that I do not wont to have again.

Is in the new modell still a belt inside?

What is your experience?

Or is it wiser to go directly to a Reckmann?

Thanks for your responses.

Best regards
Stefan
AMEL 54 N° 119 LADY CHARLYETTE, currently Dominica


NavPilot Furuno 511 - Amel 54

Stefan Schaufert
 

Dear Ameliens,

had anybody (potential?) problems with the autopilot like this?:

Recently we had some error reports on the autopilot (NAVpilot Furuno 511).

2 times: the motor for the steering is „to hot“;
1 time: there is a problem with the ruder angle (but it was only 4°).

I checked everything and found nothing but a red light at the end of the hydraulic cylinder - see attached.

 

May be the light has to be there, but I do not think so. What does it mean?
I did not find anything about it in the manual.
Otherwise the auto pilot is working fine.

Thx a lot for your thoughts.

Best regards
Stefan
AMEL 54 N°119 LADY CHARLYETTE, currently Dominica



Re: Carrying Tender on Davits while crossing

Mohammad Shirloo
 

Hi Alex;

Thanks for the reply.

Which Amel do you have? If a 54, did you have to make any modifications or make changes to the attachment points on the 310 for a good fit and connection when pulled up?

On your reply to number 5, not sure what you mean by “chaps in both cases”

Mohammad and Aty
B&B Kokomo 
Amel 54 #099

On Mar 1, 2020, at 12:48 PM, Alexander Ramseyer via Groups.Io <alexramseyer@...> wrote:

Hi Mohammad,
Coming back to your 5 questions, here are my 5 cents:
1. Good
2. The 310 works well on my Simpson Davits. I lift it with my 15HP Yamaha on.
3. I had the 310 on the  sundeck without releasing the air, but it only fits  angular
4. Offshore my 310 is not at the Davits. Why should I turn an extremely seaworthy boat into something risky?
5. Hypalon. Chaps in both cases!

Hope that helps.,
Alex


Re: Super maramu max prop

Rob Smith
 

Thanks Bill 


On Mon, 2 Mar 2020, 16:33 CW Bill Rouse, <brouse@...> wrote:
Yes,

I believe so. I will send you a private email.

Bill
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar
cloudHQPowered by
cloudHQ


On Mon, Mar 2, 2020 at 6:35 AM Rob Smith <robfromcornwall.1966@...> wrote:
Hello I am hoping someone can tell me what the correct setup on a max prop for tmd22 engine?

Many thanks 
Rob
Foresight  
SM #152


Re: Super maramu max prop

 

Yes,

I believe so. I will send you a private email.

Bill
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar
cloudHQPowered by
cloudHQ


On Mon, Mar 2, 2020 at 6:35 AM Rob Smith <robfromcornwall.1966@...> wrote:
Hello I am hoping someone can tell me what the correct setup on a max prop for tmd22 engine?

Many thanks 
Rob
Foresight  
SM #152


Super maramu max prop

Rob Smith
 

Hello I am hoping someone can tell me what the correct setup on a max prop for tmd22 engine?

Many thanks 
Rob
Foresight  
SM #152


Re: NECO 692 AUTOPILOT CONTROL UNIT

Charles Bell
 

Yes, I believe I do.

I have a full working system on Mango #29 that we were preparing to remove so we can install a new electronics package.

You are welcome to PM me and we can talk!

Charles


NECO 692 AUTOPILOT CONTROL UNIT

Alejandro Paquin
 

Good day to all,
Does anyone here have a discarded or is not using a NECO 692  Control Unit (692CU) in working condition, and would like sell it?
--
Alex Paquin
S/V " SIMPATICO"
Amel Maramu
Hull #94, 1981


Re: Carrying Tender on Davits while crossing

Alexander Ramseyer
 
Edited

Hi Mohammad,
Coming back to your 5 questions, here are my 5 cents:
1. Good
2. The 340 works well on my Simpson Davits. I lift it with my 15HP Yamaha on.
3. I had the 340 on the  sundeck without releasing the air, but it only fits  angular
4. Offshore my 340 is not at the Davits. Why should I turn an extremely seaworthy boat into something risky?
5. Hypalon. Chaps in both cases!

Hope that helps.,
Alex


Re: Size of main anchor for Super Maramu

Mark Erdos
 

A couple of unsolicited thoughts on the Mantus bridle and equipment:

 

We purchased the 3/4” bridle version when we first started cruising. It was used maybe twice. I stopped using it because the double bridles become very twisted and removing the bridle becomes a difficult task. At anchor when the winds are light and the boat drifts about, or if the boat swings with the current the lines will twist. Also the lines are very long. If you let out the full length of the bridle, you will find you have more rope than chain out defeating the purpose of having an all chain rode. Of course, you do not need to let out the full bridle but then you are not taking advantage of the chafing guards.

 

The Mantus chain hook bracket is too large to go over the bow roller. To affix it and remove it one has to hang off the side of the boat and reach down to the chain. This may not seem like a big deal until you need to get the anchor up quickly. This device is now stowed the same place with the bridle. Instead I went the low tech route. I tie a rolling hitch with my 25’ snubber. The snubber is 1” Buccaneer Medallion 8-Strand Plait Nylon Rope offering superior shock absorbency and abrasion resistance. The tensile strength is 31,000 lbs. This has served us well.

 

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Galapagos

www.creampuff.us

 

 


Re: Size of main anchor for Super Maramu

Stephen Nicholson
 

Hello Karen Smith,
From your reply regarding your Mantus anchoring equipment for SM Harmonie.
I have decided to upgrade to the 47kg Mantus anchor, as you have. 
With regard to your other Mantus equipment, can I ask:-
1) Does your Anchor Mate have the metal bracket on port or starboard side?
2) Is your Mantus snubber bridle the medium (3/4inch rope) or large (1 inch rope) size? I ask this because some pundits suggest NOT to have too thick rope on the snubber so that the rope will stretch and not snatch.
3) Are the chafing protectors in the correct places on the Mantus bridle?
4) Is your Mantus chain hook the original version, or the more recent M2 style with locking band? Any problems?
5) Is your anchor chain still 10mm? Have you upgraded your chain?
If you have the time, I would be very grateful for your advice!
Many Thanks,
Steve Nicholson
SM Antigua II #89

 


Re: Amel water cooled refrigeration & Frigoboat/Fowjet saltwater pump

Arno Luijten
 

Hi Bill,

Just to put some additional pictures with your story

The original pump as found on our Amel (hull 121) is the one in picture 1. It has the code A092819C like the one you specified. Our boat had indeed 2 pumps mounted next to each other, looking quite sad at the time we bought the boat. These are indeed a rebadged Flojet pump.

When I ordered the new pumps from Frigoboat, I received the pump in picture 2 and 3. It has the code R4105343 and Frigoboat put a sticker over it with a serial number and a notification the pump runs on 12 Volt.

As you can see it is a 24 Volt pump that they use at 12 Volt. That seemed a good idea at the time but nine moths in the tropics caused the commutator to look like picture 4. The copper is completely worn away and the pump is beyond repair. According to Flojet this is an intermittent duty pump.

I tried using a brushless mag-drive pump using about 1.3 Amps @ 12 Volt but these are centrifugal pumps that simply do not deliver enough pressure to overcome the resistance in the pipes to produce a decent flow. I’ve been told you need at least 6 liters per minute to keep the compressors happy.

I’m now using the Flojet pump you mention as well, the 4105-512 accepting for now the pump will need replacement quite frequently.

I admire the work that Oliver did with replacing the insulation of the freezer cabinet. That seems by far the best thing to do for the tropics. Also replacing the motor of the Flojet pump with a brushless motor seems a very good idea. These two modifications would solve 80% of the problem.
The remainder ideally would be solved by using a circulation system with heat radiators on the underside of the boat. and using coolant liquid as circulation fluid. But that would mean additional holes in the boat and all the rest,

But for now my first action is to get a brushless motor for the Flojet pump-head.

Cheers,

Arno Luijten
SV Luna,
A54-121