Re: Volvo parts
Paul Dowd and Sharon Brown
Hi Alex,
I would be interested in that. We do intend to be back probably in November.
Cheers, Paul S/Y Ya Fohi - Amel 54 #98 - Grenada
From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Alexander Ramseyer
Sent: 16 June 2020 21:37 To: main@AmelYachtOwners.groups.io Subject: Re: [AmelYachtOwners] Volvo parts
Paul, -- Cheers Paul Ya Fohi - Amel 54 #98
|
|||||||||||||
|
|||||||||||||
Re: Microwave oven on Amel 54
Thanks Randall, But no I don’t know anyone in Gib. I am sure I can find something on Amazon.
toggle quoted messageShow quoted text
Kind regards Nick Amelia AML54-019 Kilada Greece.
|
|||||||||||||
|
|||||||||||||
Re: FW: Replacement HP hoses for Dessalator - UPDATE
Should be OK if 3/8” is indeed the fitting size you need. A 3/8” fitting is larger than 3/8”. You can google NPT fitting dimensions. On previous boat, only one fitting swiveled. Both swiveling is OK, a bit easier to assemble.
toggle quoted messageShow quoted text
~~~⛵️~~~Matt
On Jun 17, 2020, at 12:47 AM, Mark Erdos <mcerdos@...> wrote:
|
|||||||||||||
|
|||||||||||||
Re: replacing mirrors in bathroom
Lior Keydar
Dear Alex
I replaced all the 5 mirrors on my A54 two years ago. It was a big challenge to remove the glued mirror from the bathroom at the back. I did it with a string between the mirrors and the wood wall. There is a special thin and coarse string that is special made for it. I did not get it so I use a very thin metal string that was not so coarse. It took me a few hours to remove it. I have ordered the same glas mirrors in size and glued it with silicon. Best regards Lior A54 #18
|
|||||||||||||
|
|||||||||||||
Re: FW: Replacement HP hoses for Dessalator - UPDATE
On Kristy, 3ft would be enough, 4 would be better.
On Jun 16, 2020 10:26 PM, Mark Erdos <mcerdos@...> wrote:
|
|||||||||||||
|
|||||||||||||
Re: FW: Replacement HP hoses for Dessalator - UPDATE
Thanks Bill and Kent!
Bill, I just put in 3’ so I could get a rough cost. I haven’t actually measured it yet. You’re very observant.
With best regards,
Mark
Skipper Sailing Vessel - Cream Puff - SM2K - #275 Currently cruising - Tahiti, French Polynesia www.creampuff.us
From:
main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On
Behalf Of CW Bill Rouse
I do not know about the length. A SM with a D160 with membranes in the ceiling needs about 6' for each. Remember one hose is connected at the back of the control panel.
The rest looks good to me, just questioning length.
Bill
On Tue, Jun 16, 2020 at 5:43 PM Mark Erdos <mcerdos@...> wrote:
|
|||||||||||||
|
|||||||||||||
Re: air conditioning maramu
Hey Guys!
I bought Eric Lindholms Maramu back in 2012. Since then i’ve upgraded the HVAC to a new 2018 Marine Air EnviroComfort Air Conditioning with Reverse Cycle Heat Retrofit Kit from Defender. This unit pushes more air and is also quieter! Cheers, Jer -- Jeremy Hermanns - "Jer" SVCerulean.com Maramu #105 Marina Del Rey, CA
|
|||||||||||||
|
|||||||||||||
Re: FW: Replacement HP hoses for Dessalator - UPDATE
Hi Mark, That sounds right, but am not certain of the thread size, I would encourage you to insist on 316 stainless. Kent SM243 Kristy
On Jun 16, 2020 6:47 PM, Mark Erdos <mcerdos@...> wrote:
|
|||||||||||||
|
|||||||||||||
Re: FW: Replacement HP hoses for Dessalator - UPDATE
I do not know about the length. A SM with a D160 with membranes in the ceiling needs about 6' for each. Remember one hose is connected at the back of the control panel. The rest looks good to me, just questioning length. Bill
On Tue, Jun 16, 2020 at 5:43 PM Mark Erdos <mcerdos@...> wrote:
|
|||||||||||||
|
|||||||||||||
Re: wiring schematic
The 54 has the socket, the SM does not have the socket unless the option was purchased.
On Tue, Jun 16, 2020 at 4:33 PM Arno Luijten <arno.luijten@...> wrote: Hi Ulrich & Randall,
|
|||||||||||||
|
|||||||||||||
Re: Replacement HP hoses for Dessalator
Mark, Here are a few PEARS from my book:
On Tue, Jun 16, 2020 at 3:40 PM Mark Erdos <mcerdos@...> wrote:
|
|||||||||||||
|
|||||||||||||
FW: Replacement HP hoses for Dessalator - UPDATE
I am wondering if someone who has ordered or understands HP hoses for the water maker would be kind enough to take a quick peek at this (before I push the buy button) and make sure this is correct:
HT-06-ASB | 3/8" HYDRAULAX TOUGH™ Hydraulic Hose Assembly Code: HT-06-ASB Fitting #1: SS-FJX-06-06 | (Stainless)3/8" JIC 37° Flare Female Swivel (SS-FJX-06-06) Fitting #2: SS-FJX-06-06 | (Stainless)3/8" JIC 37° Flare Female Swivel (SS-FJX-06-06) Overall Length: 3 feet 0 inches
These are about US$85 per 3’ hose assembled.
With best regards,
Mark
Skipper Sailing Vessel - Cream Puff www.creampuff.us
From: Mark Erdos [mailto:mcerdos@...]
Sent: Tuesday, June 16, 2020 10:44 AM To: 'AmelYachtOwners@groups.io' Subject: Replacement HP hoses for Dessalator
A call out to USA owners,
I have a box of supplies being assembled in the USA for shipment to Tahiti. I would like to include replacement HP hoses for the Amel installed D60 Dessalator. I am unsure of the exact specs for the fittings although I have searched the forum and think it is stainless steel 3/8 inch JIC fittings on all ends. The stuff I am unsure about is if the hose has to be “food grade” and the pressure rating.
Does anyone have a company from whom I can order on-line or better still provide me with a part number and e-tailer?
I have an email out to balcen.com (the USA Dessalator dealer) – I expect they supply it but am assuming it will be expensive and other options might prove more thifty.
With best regards,
Mark
Skipper Sailing Vessel - Cream Puff - SM2K - #275 Currently cruising - Tahiti, French Polynesia www.creampuff.us
|
|||||||||||||
|
|||||||||||||
Re: wiring schematic
Hi Ulrich & Randall,
Our Amel does not have the dive compressor. However the 230 Volt plus is still installed in the port lazarette. It's one of those blue, big ones like for shore power plugs. I'm a bit surprised by the inflator plug as present in the schematic diagram. Our Amel 54 does not have a 24 Volt socket in the rear lazarette but it does have a 230 Volt socket in this lazarette. It also came with an inflator pump running on 230 Volt. So it could be that Amel changed the voltage for the inflator at some point. Regards, Arno Luijte SV Luna, A54-121
|
|||||||||||||
|
|||||||||||||
Re: Microwave oven on Amel 54
Randall Walker
Nick, It's a long shot, but if you know somebody in Gibraltar, I would give it to you. As I have a new microwave and have no use for the rack I have. Hope you know someone here. Let me know. Cheers, Randall
On Tue, Jun 16, 2020 at 10:33 AM ngtnewington Newington via groups.io <ngtnewington=aol.com@groups.io> wrote: I have lost the wire rack that fits inside the microwave oven on “Amelia”. I am in the UK and Amelia is in Greece. I want to order a replacement.
|
|||||||||||||
|
|||||||||||||
Re: Replacement HP hoses for Dessalator
Thanks Matt. That make perfect sense.
With best regards,
Mark
Skipper Sailing Vessel - Cream Puff - SM2K - #275 Currently cruising - Tahiti, French Polynesia www.creampuff.us
From: main@AmelYachtOwners.groups.io
[mailto:main@AmelYachtOwners.groups.io] On Behalf Of Matt Salatino via
groups.io
Sent: Tuesday, June 16, 2020 10:50 AM To: main@amelyachtowners.groups.io Cc: AmelYachtOwners@groups.io Subject: Re: [AmelYachtOwners] Replacement HP hoses for Dessalator
“food grade” is a misnomer here. The high pressure hoses are always carrying seawater, only filtered through a sediment filter. It’s not drinkable water. The product water comes from the other side of the membrane, under much lower pressure. That lower pressure hose should be suitable to move drinkable water. The key is to use stainless fittings on the high pressure hose ends to keep them from corroding. ~~~⛵️~~~Matt
|
|||||||||||||
|
|||||||||||||
Re: Replacement HP hoses for Dessalator
“food grade” is a misnomer here. The high pressure hoses are always carrying seawater, only filtered through a sediment filter. It’s not drinkable water. The product water comes from the other side of the membrane, under much lower pressure. That lower pressure hose should be suitable to move drinkable water.
toggle quoted messageShow quoted text
The key is to use stainless fittings on the high pressure hose ends to keep them from corroding. ~~~⛵️~~~Matt
On Jun 16, 2020, at 10:44 PM, Mark Erdos <mcerdos@...> wrote:
|
|||||||||||||
|
|||||||||||||
Replacement HP hoses for Dessalator
A call out to USA owners,
I have a box of supplies being assembled in the USA for shipment to Tahiti. I would like to include replacement HP hoses for the Amel installed D60 Dessalator. I am unsure of the exact specs for the fittings although I have searched the forum and think it is stainless steel 3/8 inch JIC fittings on all ends. The stuff I am unsure about is if the hose has to be “food grade” and the pressure rating.
Does anyone have a company from whom I can order on-line or better still provide me with a part number and e-tailer?
I have an email out to balcen.com (the USA Dessalator dealer) – I expect they supply it but am assuming it will be expensive and other options might prove more thifty.
With best regards,
Mark
Skipper Sailing Vessel - Cream Puff - SM2K - #275 Currently cruising - Tahiti, French Polynesia www.creampuff.us
|
|||||||||||||
|
|||||||||||||
Re: Volvo parts
Paul,
I changed my engine to Beta Marine and I still have tons of Volvo parts that I could give you for a good price. Will you be back in Grenada this season? Fair winds, Alex
|
|||||||||||||
|
|||||||||||||
Re: Microwave grill rack for Amel 54
Fantastic Barry and Penny. Just what I need to know…
toggle quoted messageShow quoted text
Nick Amelia AML 54-019 Kilada Greece Connor via groups.io <connor_barry=yahoo.com@groups.io> wrote:
|
|||||||||||||
|
|||||||||||||
Microwave grill rack for Amel 54
Hi Nick,
See below photos of the grill rack. Hope you can source a replacement. Best Barry and Penny “SV Lady Penelope II” Amel 54. #17 Sainte Anne anchorage Martinique
|
|||||||||||||
|