Date   

Re: Machine shop in Tahiti

Scott SV Tengah
 

Have you friend reach out to me and I can set him up with the Russian. That guy is cheap and knows the lay of the land. 

He can also look up the Societies compendium written by fellow cruisers. A few companies listed there. There's a local who lived in NZ for many years and speaks great English. Haven't used him but hear good things. He's in the doc. 

Technimarine could maybe do it but $$$$$ and you might not get what you pay for. 
--
Scott 
2007 A54 #69
SV Tengah
http://www.svtengah.com


Re: Machine shop in Tahiti

Porter McRoberts
 

There is plenty of support there. You can buy all the replacement seals and bearings at Tahiti Roulement. And plenty of folks who can help. Scott, have the number of your Russian engineer?  


Porter McRoberts 
S/V IBIS 
A54-152

On Jan 27, 2021, at 1:03 PM, Mike Longcor (SV Trilogy) <svtrilogy53@...> wrote:

Hello Everybody,

Can anyone recommend a good machine shop in Pape'ete for rebuilding the outhaul gearbox? Has anyone had this done in Tahiti before? The bronze worm gear has likely been sheared by the steel worm. The unit is a Leroy Somer.

Asking for a friend who is currently on passage from NZ to Tahiti on a Super Maramu.

Cheers,
Mike Longcor
SV Trilogy SM23
Opua, NZ


Machine shop in Tahiti

Mike Longcor (SV Trilogy)
 

Hello Everybody,

Can anyone recommend a good machine shop in Pape'ete for rebuilding the outhaul gearbox? Has anyone had this done in Tahiti before? The bronze worm gear has likely been sheared by the steel worm. The unit is a Leroy Somer.

Asking for a friend who is currently on passage from NZ to Tahiti on a Super Maramu.

Cheers,
Mike Longcor
SV Trilogy SM23
Opua, NZ


Re: Amel 55 Webasto install

Billy Newport
 

Found 2 things this morning. The light for the heater indicator in the engine room is an normal bulb and was blown hence no flashing.

The burner on the webasto was seriously burned up and coked. The unit doesn't look like it's been serviced since factory and I put 3 months on it up to this week or 2k hours. You are supposed to clean the burner every 1000-1500 hours so this isn't unexpected at this point. New burner is 500 USD more or less.


Amel 55 Webasto install

Billy Newport
 

My Webasto is acting up and stopping during operation. Normally, there would be a switch with on/off and a LED to indicate fault codes. There is also a fuse block with a F1 (20A), F2 (5A) and a F3 (20A).

Amel custom installs this heater so there is no "normal" switch and no normal fuse block. There is a heater start/stop on the DC breaker panel by the nav table. This normally starts/stops it. There is on a box on the fwd bulk head in the engine room a white box with bilge/inverter/heater breakers. If the panel is removed then there is also 2 x 2A fuses seemingly attached to the harness from the webasto.

My question is how is this all wired up? Is the breaker in the engine room the normal switch? Are the 2 2A fuses F1/F2/F3 or something else? The amel manual doesn't really cover this much.

The LED in the engine room does not flash in my case to indicate the fault code. The heater was running 24/7 for about 2.5 months before it stopped while I was away and I have managed to get it to run twice since returning but it shuts down again with no code after 10-18 hours of normal operation.

When I got the boat, the pressure guage for the heater was 0 bar. I added water to the circuit, bringing it up to 1 bar and when it ran, the pressure rose to just under 1.5 bar.

When I returned this weekend after it stopped, I noticed the cold pressure was back to 0 again. I recharged it to 1 bar and the heater worked later that night but not when I recharged it.

When it stopped today, the pressure was still normal (1.4 bar hot).

Without the code, it's hard to get any remote help. I cannot get out of lock mode (when it stopped with a fault) without knowing where F1/F2/F3 are.

Any help appreciated.


Re: Hardtop for Amel 54 and SM

VICTOR MOLERO
 

Hello all.
I am interested. Of course it depends on price and design.
Thanks.
Victor  
SM314 Alendoy


looking for a good friend a Super Maramu

jlm@jlmertz.fr
 

Hello,
I'm looking for a good friend who just sold his boat a Super Maramu or Super Maramu 2000.
If you know of someone who sells their boat, please let me know.
Best regards
Jean Luc MERTZ
CottonBay
Agde France
00 33 663 393 174
SM 316


Re: Hardtop for Amel 54 and SM

Paul Osterberg
 

I'm also interested in a hard top, Might be a project for next off season, if anyone have ideas or photos please let us know
Paul on SY Kerpa SM#259, Lagos Portugal


Re: Hardtop for Amel 54 and SM

Dimitris Krasopoulos
 

I agree if the shipment is from Europe to avoid taxes and custom

D Krasopoulos
Amel 54

Στάλθηκε από το iPhone of Dimitris Krasopoulos 

On 26 Jan 2021, at 11:29, Philippe Chatton <chattonp960@...> wrote:


Hi everyone
I noticed that several SM owners seem to have an interest in a hard top - including myself.
At one point in time we might consider a group order, assuming we can identify a model / manufacturer, and should an interest be confirmed.  
Kind regards
Philippe
S/V Chameleon - Antibes FR
 

Le lun. 25 janv. 2021 à 21:54, Annsofie & Jonas Svanberg <ann-sofie@...> a écrit :
Hi Mohammed
I have got some requests for more pictures. I will put a .pdf together showing it. Just give me a day or two.

The original roof is made by a friend if us and is a sandwich construction with divinycell inbetween the GRP.

Regards
Ann-Sofie
S/Y Lady Annila
SM 232, 1998
Present in Algarve, Portugal 


Skickat från min iPhone

25/01/2021 kl. 19:17 skrev Mohammad Shirloo <mshirloo@...>:



Hello Halsinger;

 

Nice looking hard top. Do you have more pictures and/or videos that show more detail?

 

Where did you have this top fabricated?

 

Happy Sailing;

 

 

Mohammad and Aty

B&B Kokomo

AMEL 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Annsofie & Jonas Svanberg via groups.io
Sent: Monday, January 25, 2021 10:51 AM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Hardtop for Amel 54

 

Here is our hard top on S/Y Lady Annila, SM 232.

 

It has been there since 2010 and during 2020 we hade it renovated. On top we have 2 solar panels 364 W each. (And an orher three on the arch)


<image001.jpg>

Hälsningar

Ann-Sofie 

S/Y Lady Annila

SM 232, 1998

 

 

Skickat från min iPhone



25/01/2021 kl. 17:36 skrev VICTOR MOLERO <victor.moleroxx@...>:



Congratulations! I love it!

Do you, or anyone, know if the solution is feasible for a Super Maramu 2000? Any idea about the cost?

It's a wonderful improvement, very well thought out.

Thanks for sharing.

Victor 

SM314 Alendoy


Re: Hardtop for Amel 54 and SM

Philippe Chatton
 

Hi everyone
I noticed that several SM owners seem to have an interest in a hard top - including myself.
At one point in time we might consider a group order, assuming we can identify a model / manufacturer, and should an interest be confirmed.  
Kind regards
Philippe
S/V Chameleon - Antibes FR
 

Le lun. 25 janv. 2021 à 21:54, Annsofie & Jonas Svanberg <ann-sofie@...> a écrit :
Hi Mohammed
I have got some requests for more pictures. I will put a .pdf together showing it. Just give me a day or two.

The original roof is made by a friend if us and is a sandwich construction with divinycell inbetween the GRP.

Regards
Ann-Sofie
S/Y Lady Annila
SM 232, 1998
Present in Algarve, Portugal 


Skickat från min iPhone

25/01/2021 kl. 19:17 skrev Mohammad Shirloo <mshirloo@...>:



Hello Halsinger;

 

Nice looking hard top. Do you have more pictures and/or videos that show more detail?

 

Where did you have this top fabricated?

 

Happy Sailing;

 

 

Mohammad and Aty

B&B Kokomo

AMEL 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Annsofie & Jonas Svanberg via groups.io
Sent: Monday, January 25, 2021 10:51 AM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Hardtop for Amel 54

 

Here is our hard top on S/Y Lady Annila, SM 232.

 

It has been there since 2010 and during 2020 we hade it renovated. On top we have 2 solar panels 364 W each. (And an orher three on the arch)


<image001.jpg>

Hälsningar

Ann-Sofie 

S/Y Lady Annila

SM 232, 1998

 

 

Skickat från min iPhone



25/01/2021 kl. 17:36 skrev VICTOR MOLERO <victor.moleroxx@...>:



Congratulations! I love it!

Do you, or anyone, know if the solution is feasible for a Super Maramu 2000? Any idea about the cost?

It's a wonderful improvement, very well thought out.

Thanks for sharing.

Victor 

SM314 Alendoy


Re: Webasto thermopro question

Peter Tiner
 

Hi

i run the Webasto from remote over gsm. Boat is in the water some 500km away in Sweden. It gets cold now and then so i use it if the radiators should not be sufficient. You can can find the swedish supplier here : https://gsm-start.se/en/
Attaching some pics showing possibilities.

\Peter @ SY Maiken A54 #52


Re: Hardtop for Amel 54

Mohammad Shirloo
 

Hi Ann-Sofie;

 

That’s great, thank you.

 

Happy Sailing;

 

 

Mohammad and Aty

B&B Kokomo

AMEL 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Annsofie & Jonas Svanberg via groups.io
Sent: Monday, January 25, 2021 12:38 PM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Hardtop for Amel 54

 

Hi Mohammed

I have got some requests for more pictures. I will put a .pdf together showing it. Just give me a day or two.

 

The original roof is made by a friend if us and is a sandwich construction with divinycell inbetween the GRP.

Regards

Ann-Sofie

S/Y Lady Annila

SM 232, 1998

Present in Algarve, Portugal 

 

 

Skickat från min iPhone



25/01/2021 kl. 19:17 skrev Mohammad Shirloo <mshirloo@...>:



Hello Halsinger;

 

Nice looking hard top. Do you have more pictures and/or videos that show more detail?

 

Where did you have this top fabricated?

 

Happy Sailing;

 

 

Mohammad and Aty

B&B Kokomo

AMEL 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Annsofie & Jonas Svanberg via groups.io
Sent: Monday, January 25, 2021 10:51 AM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Hardtop for Amel 54

 

Here is our hard top on S/Y Lady Annila, SM 232.

 

It has been there since 2010 and during 2020 we hade it renovated. On top we have 2 solar panels 364 W each. (And an orher three on the arch)

 

<image001.jpg>

Hälsningar

Ann-Sofie 

S/Y Lady Annila

SM 232, 1998

 

 

Skickat från min iPhone




25/01/2021 kl. 17:36 skrev VICTOR MOLERO <victor.moleroxx@...>:



Congratulations! I love it!

Do you, or anyone, know if the solution is feasible for a Super Maramu 2000? Any idea about the cost?

It's a wonderful improvement, very well thought out.

Thanks for sharing.

Victor 

SM314 Alendoy


Re: Hardtop for Amel 54

VICTOR MOLERO
 

Thank you Ann Sophie.
I will appreciate more pictures, if you have them available and willing to share.
Thanks.
Victor 
SM314 Alendoy


Re: Hardtop for Amel 54

Ann-Sofie, S/Y Lady Annila
 

Hi Mohammed
I have got some requests for more pictures. I will put a .pdf together showing it. Just give me a day or two.

The original roof is made by a friend if us and is a sandwich construction with divinycell inbetween the GRP.

Regards
Ann-Sofie
S/Y Lady Annila
SM 232, 1998
Present in Algarve, Portugal 


Skickat från min iPhone

25/01/2021 kl. 19:17 skrev Mohammad Shirloo <mshirloo@...>:



Hello Halsinger;

 

Nice looking hard top. Do you have more pictures and/or videos that show more detail?

 

Where did you have this top fabricated?

 

Happy Sailing;

 

 

Mohammad and Aty

B&B Kokomo

AMEL 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Annsofie & Jonas Svanberg via groups.io
Sent: Monday, January 25, 2021 10:51 AM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Hardtop for Amel 54

 

Here is our hard top on S/Y Lady Annila, SM 232.

 

It has been there since 2010 and during 2020 we hade it renovated. On top we have 2 solar panels 364 W each. (And an orher three on the arch)


<image001.jpg>

Hälsningar

Ann-Sofie 

S/Y Lady Annila

SM 232, 1998

 

 

Skickat från min iPhone



25/01/2021 kl. 17:36 skrev VICTOR MOLERO <victor.moleroxx@...>:



Congratulations! I love it!

Do you, or anyone, know if the solution is feasible for a Super Maramu 2000? Any idea about the cost?

It's a wonderful improvement, very well thought out.

Thanks for sharing.

Victor 

SM314 Alendoy


Re: Hardtop for Amel 54

Mohammad Shirloo
 

Hello Halsinger;

 

Nice looking hard top. Do you have more pictures and/or videos that show more detail?

 

Where did you have this top fabricated?

 

Happy Sailing;

 

 

Mohammad and Aty

B&B Kokomo

AMEL 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Annsofie & Jonas Svanberg via groups.io
Sent: Monday, January 25, 2021 10:51 AM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Hardtop for Amel 54

 

Here is our hard top on S/Y Lady Annila, SM 232.

 

It has been there since 2010 and during 2020 we hade it renovated. On top we have 2 solar panels 364 W each. (And an orher three on the arch)


Hälsningar

Ann-Sofie 

S/Y Lady Annila

SM 232, 1998

 

 

Skickat från min iPhone



25/01/2021 kl. 17:36 skrev VICTOR MOLERO <victor.moleroxx@...>:



Congratulations! I love it!

Do you, or anyone, know if the solution is feasible for a Super Maramu 2000? Any idea about the cost?

It's a wonderful improvement, very well thought out.

Thanks for sharing.

Victor 

SM314 Alendoy


Re: Hardtop for Amel 54

Ann-Sofie, S/Y Lady Annila
 

Here is our hard top on S/Y Lady Annila, SM 232.

It has been there since 2010 and during 2020 we hade it renovated. On top we have 2 solar panels 364 W each. (And an orher three on the arch)


Hälsningar
Ann-Sofie 
S/Y Lady Annila
SM 232, 1998


Skickat från min iPhone

25/01/2021 kl. 17:36 skrev VICTOR MOLERO <victor.moleroxx@...>:


Congratulations! I love it!
Do you, or anyone, know if the solution is feasible for a Super Maramu 2000? Any idea about the cost?
It's a wonderful improvement, very well thought out.
Thanks for sharing.
Victor 
SM314 Alendoy


Re: Hardtop for Amel 54

VICTOR MOLERO
 

Congratulations! I love it!
Do you, or anyone, know if the solution is feasible for a Super Maramu 2000? Any idea about the cost?
It's a wonderful improvement, very well thought out.
Thanks for sharing.
Victor 
SM314 Alendoy


Webasto thermopro question

Billy Newport
 

I'm living on my 55 right now which is in the water in jersey city, nj. I was away visiting family over christmas. I have a raspberry pi on my boat running the usual IOT stack (RTL433/Influxdb/telegraf/grafana/vncserver). This PI is connected to a wifi hotspot on the boat for remote access. It captures all NMEA data and temperatures (cheap 433mhz temp/humidity sensors distributed around the boat), room temps, fridge freezer temps, frigobaot compressor temps, engine room temps and so on, stores it in a database and uses grafana to look at data which is super handy to figure out what the hell just happened.

I noticed saturday (logged in to the raspberry from Ohio using vncserver) evening that on Friday at 8pm the temp in the boat started dropping. Heater issue. So I drove 8 hours back to the boat arriving about 4am. I got the heater working again yesterday so we're toasty again.

The heater appears to have no display or even LED that I can see so I can't see why it stopped. Does anyone have a display on theirs or is there a way to do a wifi type situation where it can be checked remotely or restarted remotely?

Billy (55#56)


Re: Mastervolt installation help

Billy Newport
 

Hi Arno,
I have everything hooked up now and want to upgrade everythings firmware which appears to need the installer password. If you can email it to me at billy at billynewport dot com I'd be grateful.

THanks
Billy (55#56)


Re: Hardtop for Amel 54

Justin Maguire
 

Super nice solution – well though out, well made.

 

Sent from Mail for Windows 10

 


From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> on behalf of Stefan Schaufert <mail@...>
Sent: Monday, January 25, 2021 6:16:42 AM
To: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io>
Subject: Re: [AmelYachtOwners] Hardtop for Amel 54
 
Here is another suggestion.

The two Vacuum-Epoxy-Lightweight-Parts where made in Le Marin by ALIZE COMPOSITES (Manu).
It is the same company made the not any longer existing mold for the hardtop.
All other (small) modifications/ materials came also from the yard in Le Marin.
The rest was a lot of manual work by ourselves.

The old bimini frame is still used.  A very functional and economical variant.  It carries 680W solar, collects rainwater, allows a very good all-round view, has an integrated grip edge and the sails can also be visually checked from the armchair.  My wife just uploaded a video about this at:
https://youtu.be/7GIHQd4l3FI

Best regards
Stefan
A54 #119 Lady Charlyette, currently Exumas

1701 - 1720 of 57923