Date   

Re: Cockpit cusions measurement

 

Be careful, the shape is not at 90-degree angles. 
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Thu, Apr 29, 2021 at 2:17 AM Arnold Mente via groups.io <Arnold.mente=me.com@groups.io> wrote:
Dear ALL,

I would need the measurement of the seats in the cockpit, I am not sure done it right and now fare away of may boat.
Thank you for answer!


--
Arnold
SY Zephyr SM203


Re: Motor for raising and lowering thruster

 

I am not sure if the Actuator in the Mago is the same as the SM which is 24 volts, but this info may help you. The SM actuator is Model Number: ACLE105 and made by:
SNT
2 rue Marcel DASSAULT
ZI de la Croix St Nicolas
94510 La queue en brie, France
Email: snt.contact@... or
secretariat@...
https://www.snt.tm.fr/fr
image.png
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Thu, Apr 29, 2021 at 1:08 AM Kaplan,Andre <kaplan@...> wrote:
To all,
I have a 1989 Mango and the motor that raises and lowers thruster propeller appears to be dead. Does anyone know where to source such a motor?

Andre Kaplan 
Renaissance 2000
Mango 71 88




Begin forwarded message:

From: "Paul Stascavage via groups.io" <pstas2003=yahoo.com@groups.io>
Date: April 27, 2021 at 11:15:57 PM EDT
To: main@amelyachtowners.groups.io
Subject: [AmelYachtOwners] Passageway berth wall fabric cleaning advice
Reply-To: main@amelyachtowners.groups.io


*** Attention: This is an external email. Use caution responding, opening attachments or clicking on links. ***
Paul,

We spent much of this past winter in cold weather climates and that area was one of the first we noticed the mold stains.  We tried vinegar as well as many other products, but the only one that worked for us on that material, in a timely fashion, was Tilex (which contains a significant amount of bleach).  Spray it on with a good deal of ventilation and wait a few hours.  Dry the area with a fan to get rid of the bleach odors.  Repeat if necessary. That material is colorfast but the bleach will lighten the color a bit as it bleaches out old dirt and grime.  We had to treat the entire area to end up with a uniformly clean surface.

Something else that we found that works on fabric and carpet (but takes a good deal of time) is what piratical sailor (https://www.practical-sailor.com/boat-maintenance/fighting-mildew-mold-and-lichen) calls formula b:

2 tablespoons of baking soda
2 tablespoons of borax
1 tablespoon of trisodiumphosphate (TSP)

Mix in 1 quart of warm water with stirring.

What  worked for us on fabric and carpet is to spray the area with the formula b and let sit for a few days.  Come back with vinegar and a brush.  Repeat until the stains are completely gone, which could be 3 or 4 applications. 

If you spent a good deal of time under those conditions, I suggest looking around the boat for other potentially impacted areas.

Cabinets, lockers, closets, under berths, etc. Any areas close to the hull is where there would have been excessive condensation and possibly a problem.

We just completed an extensive cleaning of the boat from stem to stern.  Feel free to email me (paul dot stascavage at icloud dot com) if you find your problem is more extensive than you thought and I will share what I have learned.

All the best,

Paul Stascavage
SM #466 - s/v Rita Kathryn
Exploring Brunswick, GA

www.RitaKathryn.com


Re: Insurance

Eric Freedman
 

Hi,

What model Amel do you have?

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io On Behalf Of Billy Newport
Sent: Wednesday, April 28, 2021 10:39 PM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Insurance

 

I got my surprise from Boat US today. I'm moving my Amel from NJ to NJ, literally 20 miles to a different marina and my annual premium went from 3.7K to 11.4K. No good reason for this rise, "crime", "could be more exposed to weather" etc. Shopping around now.


Re: Deck hatch dogs reinforcements

Eric Freedman
 

Pierre,

Thank you !

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io On Behalf Of Pierre Blouin
Sent: Thursday, April 29, 2021 2:05 AM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Deck hatch dogs reinforcements

 

Hi Eric,
Yes, had those made at machine shop.
Rough measurements: 2 5/16 widest; 1 1/2 height; 3/16 thickness

I asked the shop to make another sample but using SS 316, and thinner. (Thanks Bill Reynolds, good idea)
I'll share picture once I have it.
To all of those who have reached out to me with orders, thanks for your patience, I will get back to you all. I think it's worth checking out how it looks in SS.

-Pierre
SV Viva, #374
Portland, OR


Re: Engine Mounts and Decoupling Vetus/Engine Block

Rudolf Waldispuehl
 

Thank you Bill

 

I have not seen something similar in the AMEL 54 Unser’s Manual not in the AMEL Owner’s Guide.

Nevertheless your information is welcomed and a good starting point, and I will take out one before ordering so I’m sure.

 

Best regards

Ruedi

 

Von: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io> im Auftrag von CW Bill Rouse <brouse@...>
Antworten an: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Datum: Mittwoch, 28. April 2021 um 23:48
An: "main@AmelYachtOwners.groups.io" <main@amelyachtowners.groups.io>
Betreff: Re: [AmelYachtOwners] Engine Mounts and Decoupling Vetus/Engine Block

 

Ruedi,

 

The issue is that so many things changed during the production of the 54, I cannot be sure, but I know the 54 started with 6 each Vetus K50 motor mounts as shown in the Amel 54 Users Manual.

 

CW Bill Rouse Amel Owners Yacht School

Address: 720 Winnie, Galveston Island, Texas 77550 

 

View My Training Calendar

 

 

On Wed, Apr 28, 2021 at 4:36 PM Rudolf Waldispuehl <Rudolf@...> wrote:

Dear Amelians

 

I’m in the process to change Engine Mounts and not sure what type or brand of Mounts where originally used on the A54 with the Volvo D3-110.

Somebody told me that Amel used on the Amel54 with the Volvo D3-110C the Volvo Mounts. I’m not sure and can’t identify which type and brand are installed on Wasabi.

 

Maybe somebody knows which model/type originally are installed. Otherwise I’m confident that Bill Rouse knows it. 😉

@Bill; I haven’t found any reference in your AMEL School Book.

 

Best regards

Ruedi

SY WASABI

A54 #55

 

 

Von: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io> im Auftrag von Herbert Lackner <herbert@...>
Antworten an: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Datum: Sonntag, 9. Februar 2020 um 11:01
An: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Betreff: Re: [AmelYachtOwners] Engine Mounts and Decoupling Vetus/Engine Block

 

Woody,  search for "alignment" in the forum and you will find a lot of information, also what kind of mounts you need

a summary with info from Olivier:
 

in order to re-align your engine with the C-drive, you need a fixed coupling as on the pictures and drawing.

You don't need to install the shaft alternator pulley while checking alignment. 

 

Before touching the tools, make pictures and take notes (measurements of all the fittings, position of the nuts on the rubber mounts, position of the engine on the steel cradle, position of the shaft brake disc, etc...).

Start with disconnecting the hoses that could prevent you from moving the engine backwards on its cradle.

Then undo the coupling bolts and the engine steel supports' bolts (attaching the engine on the steel cradle).

Then move the engine backwards enough to remove the coupling bolts.

 

Then comes the alignment process.

AMEL uses a tool which is a steel coupling machined so that its aft side "enters" the gear-box flange (see pictures and drawing). You can also pre-install the new coupling and adjust the position of the mounts.

First bring the engine forward and make sure the coupling is centered with the gear-box flange, and can enter the gap in the flange. 

Then move the engine a little bit backwards and check that the gap between the flange and the aft side of the coupler is even all around the circumference. To adjust this, you need "thickness wedges" (used in the automotive industry) and play with the rubber mounts nuts to make the gap even.

Then bring the engine forward and tighten the bolts on the cradle and on the mounts.

 

The advantage of using the tool AMEL uses is that it is easier to install while checking the gaps.

If you need to make one, here's a drawing of the alignment tool for a YANMAR 4JH3-HTE.

The inside diameter (C-drive input shaft) is 35 mm.

The outside diameter is 100 mm.

The diameter of the part that enters the gear-box flange cylindric gap is 62.8 mm, thickness 3 mm.

 

You should use a VETUS fixed coupling for 35mm shafts, then have it machined to make the 62.8mm "plug" and drilled for the four bolts that should match the flange holes.


The process is the same for Santorins or for Super Maramus.


more info from me: 
* Amel does not sell the alignment tool, I had it made by a machine shop from Aluminium
* I would change also the C-Drive mounts when you change the engine mounts.
* Make sure that the c-drive is "open" and "sits on his rubber sleeve" before you do the engine alignment.
* I used a tool like this to lift the engine https://www.expondo.at/steinberg-systems-kettenzug-2-000-kg-3-m-10030374?gclid=EAIaIQobChMIw9i79ZrE5wIVFuDtCh07Aw33EAQYAiABEgKPs_D_BwE . the job can be done by one person

fair winds, herbert
SN120


Cockpit cusions measurement

Arnold Mente
 

Dear ALL,

I would need the measurement of the seats in the cockpit, I am not sure done it right and now fare away of may boat.
Thank you for answer!


--
Arnold
SY Zephyr SM203


Motor for raising and lowering thruster

Kaplan,Andre
 

To all,
I have a 1989 Mango and the motor that raises and lowers thruster propeller appears to be dead. Does anyone know where to source such a motor?

Andre Kaplan 
Renaissance 2000
Mango 71 88




Begin forwarded message:

From: "Paul Stascavage via groups.io" <pstas2003@...>
Date: April 27, 2021 at 11:15:57 PM EDT
To: main@amelyachtowners.groups.io
Subject: [AmelYachtOwners] Passageway berth wall fabric cleaning advice
Reply-To: main@amelyachtowners.groups.io


*** Attention: This is an external email. Use caution responding, opening attachments or clicking on links. ***
Paul,

We spent much of this past winter in cold weather climates and that area was one of the first we noticed the mold stains.  We tried vinegar as well as many other products, but the only one that worked for us on that material, in a timely fashion, was Tilex (which contains a significant amount of bleach).  Spray it on with a good deal of ventilation and wait a few hours.  Dry the area with a fan to get rid of the bleach odors.  Repeat if necessary. That material is colorfast but the bleach will lighten the color a bit as it bleaches out old dirt and grime.  We had to treat the entire area to end up with a uniformly clean surface.

Something else that we found that works on fabric and carpet (but takes a good deal of time) is what piratical sailor (https://www.practical-sailor.com/boat-maintenance/fighting-mildew-mold-and-lichen) calls formula b:

2 tablespoons of baking soda
2 tablespoons of borax
1 tablespoon of trisodiumphosphate (TSP)

Mix in 1 quart of warm water with stirring.

What  worked for us on fabric and carpet is to spray the area with the formula b and let sit for a few days.  Come back with vinegar and a brush.  Repeat until the stains are completely gone, which could be 3 or 4 applications. 

If you spent a good deal of time under those conditions, I suggest looking around the boat for other potentially impacted areas.

Cabinets, lockers, closets, under berths, etc. Any areas close to the hull is where there would have been excessive condensation and possibly a problem.

We just completed an extensive cleaning of the boat from stem to stern.  Feel free to email me (paul dot stascavage at icloud dot com) if you find your problem is more extensive than you thought and I will share what I have learned.

All the best,

Paul Stascavage
SM #466 - s/v Rita Kathryn
Exploring Brunswick, GA

www.RitaKathryn.com


Re: Deck hatch dogs reinforcements

Pierre Blouin
 

Hi Eric,
Yes, had those made at machine shop.
Rough measurements: 2 5/16 widest; 1 1/2 height; 3/16 thickness

I asked the shop to make another sample but using SS 316, and thinner. (Thanks Bill Reynolds, good idea)
I'll share picture once I have it.
To all of those who have reached out to me with orders, thanks for your patience, I will get back to you all. I think it's worth checking out how it looks in SS.

-Pierre
SV Viva, #374
Portland, OR


Re: Who can guess what this is

Ian Park
 

It is the extension to the table. Look under the edge on the bench seat side and you will see to plastic sockets that the pots slide into.
Now you can have bigger parties!!

Ian

Ocean Hobo


Re: Who can guess what this is

Mark Erdos
 

Mark,

 

This is used to trap people in the forward part of the boat since getting around the salon table with this leaf in it requires a level of acrobatic skills.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Tahiti, French Polynesia

www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Garver via groups.io
Sent: Wednesday, April 28, 2021 9:35 AM
To: AmelYachtOwners@groups.io
Subject: [AmelYachtOwners] Who can guess what this is

 

Greetings! This has been in the front hanging locker and I only saw part of it and had thought it was the small cockpit table. Today, I pulled it out and I have no idea what this is for. The stainless “legs” do not move and look like they are meant to be inserted/installed in something, somewhere. Anyone have the answer?

 


Re: Insurance

Billy Newport
 

I got my surprise from Boat US today. I'm moving my Amel from NJ to NJ, literally 20 miles to a different marina and my annual premium went from 3.7K to 11.4K. No good reason for this rise, "crime", "could be more exposed to weather" etc. Shopping around now.


Re: Mastervolt Alpha High-Output Alternator Temperature when charging LiFePO4

Dean Gillies
 

On Wed, Apr 28, 2021 at 11:15 PM, Arno Luijten wrote:
you could just stick a Amazon remote thermometer on the alternator
Hi Arno,
That's a great idea!  Even better, the Multiplus device in the test system I have built here at home was supplied with a temperature sensor which is not needed for the Lithium cells, but can be connected to the Cerbo GX. I have now done that, and it works perfectly, providing a dashboard readout as well as a permanent log of temperature through VRM. 

I just need to bolt the sensor to the alternator B- terminal and hook it up to the Cerbo GX. The permanent logging will show me the temperature profile as the alternator runs in practice.  

Thanks Arno, a very simple solution!

Dean SV Stella
A54-154



Re: Engine Mounts and Decoupling Vetus/Engine Block

 

Ruedi,

The issue is that so many things changed during the production of the 54, I cannot be sure, but I know the 54 started with 6 each Vetus K50 motor mounts as shown in the Amel 54 Users Manual.

image.png
image.png
image.png
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Wed, Apr 28, 2021 at 4:36 PM Rudolf Waldispuehl <Rudolf@...> wrote:

Dear Amelians

 

I’m in the process to change Engine Mounts and not sure what type or brand of Mounts where originally used on the A54 with the Volvo D3-110.

Somebody told me that Amel used on the Amel54 with the Volvo D3-110C the Volvo Mounts. I’m not sure and can’t identify which type and brand are installed on Wasabi.

 

Maybe somebody knows which model/type originally are installed. Otherwise I’m confident that Bill Rouse knows it. 😉

@Bill; I haven’t found any reference in your AMEL School Book.

 

Best regards

Ruedi

SY WASABI

A54 #55

 

 

Von: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io> im Auftrag von Herbert Lackner <herbert@...>
Antworten an: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Datum: Sonntag, 9. Februar 2020 um 11:01
An: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Betreff: Re: [AmelYachtOwners] Engine Mounts and Decoupling Vetus/Engine Block

 

Woody,  search for "alignment" in the forum and you will find a lot of information, also what kind of mounts you need

a summary with info from Olivier:
 

in order to re-align your engine with the C-drive, you need a fixed coupling as on the pictures and drawing.

You don't need to install the shaft alternator pulley while checking alignment. 

 

Before touching the tools, make pictures and take notes (measurements of all the fittings, position of the nuts on the rubber mounts, position of the engine on the steel cradle, position of the shaft brake disc, etc...).

Start with disconnecting the hoses that could prevent you from moving the engine backwards on its cradle.

Then undo the coupling bolts and the engine steel supports' bolts (attaching the engine on the steel cradle).

Then move the engine backwards enough to remove the coupling bolts.

 

Then comes the alignment process.

AMEL uses a tool which is a steel coupling machined so that its aft side "enters" the gear-box flange (see pictures and drawing). You can also pre-install the new coupling and adjust the position of the mounts.

First bring the engine forward and make sure the coupling is centered with the gear-box flange, and can enter the gap in the flange. 

Then move the engine a little bit backwards and check that the gap between the flange and the aft side of the coupler is even all around the circumference. To adjust this, you need "thickness wedges" (used in the automotive industry) and play with the rubber mounts nuts to make the gap even.

Then bring the engine forward and tighten the bolts on the cradle and on the mounts.

 

The advantage of using the tool AMEL uses is that it is easier to install while checking the gaps.

If you need to make one, here's a drawing of the alignment tool for a YANMAR 4JH3-HTE.

The inside diameter (C-drive input shaft) is 35 mm.

The outside diameter is 100 mm.

The diameter of the part that enters the gear-box flange cylindric gap is 62.8 mm, thickness 3 mm.

 

You should use a VETUS fixed coupling for 35mm shafts, then have it machined to make the 62.8mm "plug" and drilled for the four bolts that should match the flange holes.


The process is the same for Santorins or for Super Maramus.


more info from me: 
* Amel does not sell the alignment tool, I had it made by a machine shop from Aluminium
* I would change also the C-Drive mounts when you change the engine mounts.
* Make sure that the c-drive is "open" and "sits on his rubber sleeve" before you do the engine alignment.
* I used a tool like this to lift the engine https://www.expondo.at/steinberg-systems-kettenzug-2-000-kg-3-m-10030374?gclid=EAIaIQobChMIw9i79ZrE5wIVFuDtCh07Aw33EAQYAiABEgKPs_D_BwE . the job can be done by one person

fair winds, herbert
SN120



Re: Engine Mounts and Decoupling Vetus/Engine Block

Rudolf Waldispuehl
 

Dear Amelians

 

I’m in the process to change Engine Mounts and not sure what type or brand of Mounts where originally used on the A54 with the Volvo D3-110.

Somebody told me that Amel used on the Amel54 with the Volvo D3-110C the Volvo Mounts. I’m not sure and can’t identify which type and brand are installed on Wasabi.

 

Maybe somebody knows which model/type originally are installed. Otherwise I’m confident that Bill Rouse knows it. 😉

@Bill; I haven’t found any reference in your AMEL School Book.

 

Best regards

Ruedi

SY WASABI

A54 #55

 

 

Von: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io> im Auftrag von Herbert Lackner <herbert@...>
Antworten an: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Datum: Sonntag, 9. Februar 2020 um 11:01
An: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Betreff: Re: [AmelYachtOwners] Engine Mounts and Decoupling Vetus/Engine Block

 

Woody,  search for "alignment" in the forum and you will find a lot of information, also what kind of mounts you need

a summary with info from Olivier:
 

in order to re-align your engine with the C-drive, you need a fixed coupling as on the pictures and drawing.

You don't need to install the shaft alternator pulley while checking alignment. 

 

Before touching the tools, make pictures and take notes (measurements of all the fittings, position of the nuts on the rubber mounts, position of the engine on the steel cradle, position of the shaft brake disc, etc...).

Start with disconnecting the hoses that could prevent you from moving the engine backwards on its cradle.

Then undo the coupling bolts and the engine steel supports' bolts (attaching the engine on the steel cradle).

Then move the engine backwards enough to remove the coupling bolts.

 

Then comes the alignment process.

AMEL uses a tool which is a steel coupling machined so that its aft side "enters" the gear-box flange (see pictures and drawing). You can also pre-install the new coupling and adjust the position of the mounts.

First bring the engine forward and make sure the coupling is centered with the gear-box flange, and can enter the gap in the flange. 

Then move the engine a little bit backwards and check that the gap between the flange and the aft side of the coupler is even all around the circumference. To adjust this, you need "thickness wedges" (used in the automotive industry) and play with the rubber mounts nuts to make the gap even.

Then bring the engine forward and tighten the bolts on the cradle and on the mounts.

 

The advantage of using the tool AMEL uses is that it is easier to install while checking the gaps.

If you need to make one, here's a drawing of the alignment tool for a YANMAR 4JH3-HTE.

The inside diameter (C-drive input shaft) is 35 mm.

The outside diameter is 100 mm.

The diameter of the part that enters the gear-box flange cylindric gap is 62.8 mm, thickness 3 mm.

 

You should use a VETUS fixed coupling for 35mm shafts, then have it machined to make the 62.8mm "plug" and drilled for the four bolts that should match the flange holes.


The process is the same for Santorins or for Super Maramus.


more info from me: 
* Amel does not sell the alignment tool, I had it made by a machine shop from Aluminium
* I would change also the C-Drive mounts when you change the engine mounts.
* Make sure that the c-drive is "open" and "sits on his rubber sleeve" before you do the engine alignment.
* I used a tool like this to lift the engine https://www.expondo.at/steinberg-systems-kettenzug-2-000-kg-3-m-10030374?gclid=EAIaIQobChMIw9i79ZrE5wIVFuDtCh07Aw33EAQYAiABEgKPs_D_BwE . the job can be done by one person

fair winds, herbert
SN120



Re: Who can guess what this is

Ian Townsend
 

Main salon table extension.

Ian & Margaret
Loca Lola II
SM153

On Apr 28, 2021, at 3:35 PM, Mark Garver via groups.io <mgarver@...> wrote:

Greetings! This has been in the front hanging locker and I only saw part of it and had thought it was the small cockpit table. Today, I pulled it out and I have no idea what this is for. The stainless “legs” do not move and look like they are meant to be inserted/installed in something, somewhere. Anyone have the answer?

<IMG_6812.jpeg>


Re: Who can guess what this is

Ann-Sofie, S/Y Lady Annila
 

Here you can see it mounted.


Hälsningar
Ann-Sofie


Skickat från min iPhone

28/04/2021 kl. 21:02 skrev Ann-Sofie <ann-sofie@...>:

It is en extension to the salon table towards the small sofa. 
Under the big table there is a sort of rings mounted, where you stick the metal ”legs” into. 

regards
Ann-Sofie 
S/Y Lady Annila SM 232, 1998


Skickat från min iPhone

28/04/2021 kl. 20:39 skrev sherman.gifford via groups.io <swgifford@...>:


It's a leaf to extend the salon dining table - enjoy!! 



Sent from my Verizon, Samsung Galaxy smartphone


-------- Original message --------
From: "Mark Garver via groups.io" <mgarver@...>
Date: 4/28/21 3:35 PM (GMT-05:00)
To: AmelYachtOwners@groups.io
Subject: [AmelYachtOwners] Who can guess what this is

Greetings! This has been in the front hanging locker and I only saw part of it and had thought it was the small cockpit table. Today, I pulled it out and I have no idea what this is for. The stainless “legs” do not move and look like they are meant to be inserted/installed in something, somewhere. Anyone have the answer?

<IMG_6812.jpeg>


Re: Who can guess what this is

Ann-Sofie, S/Y Lady Annila
 

It is en extension to the salon table towards the small sofa. 
Under the big table there is a sort of rings mounted, where you stick the metal ”legs” into. 

regards
Ann-Sofie 
S/Y Lady Annila SM 232, 1998


Skickat från min iPhone

28/04/2021 kl. 20:39 skrev sherman.gifford via groups.io <swgifford@...>:


It's a leaf to extend the salon dining table - enjoy!! 



Sent from my Verizon, Samsung Galaxy smartphone


-------- Original message --------
From: "Mark Garver via groups.io" <mgarver@...>
Date: 4/28/21 3:35 PM (GMT-05:00)
To: AmelYachtOwners@groups.io
Subject: [AmelYachtOwners] Who can guess what this is

Greetings! This has been in the front hanging locker and I only saw part of it and had thought it was the small cockpit table. Today, I pulled it out and I have no idea what this is for. The stainless “legs” do not move and look like they are meant to be inserted/installed in something, somewhere. Anyone have the answer?

<IMG_6812.jpeg>


Re: Who can guess what this is

Danny and Yvonne SIMMS
 

Hi Mark, on Ocean Pearl it is another Amel wonder of attention to detail. The grain on the table and the extension match

 Danny

SM 299

Ocean Pearl

On 29 April 2021 at 07:49 "Mark Garver via groups.io" <mgarver@...> wrote:

Wow! It is! Thanks! Who knew! 

Mark Garver
S/V It’s Good
SM #105

On Apr 28, 2021, at 3:37 PM, Dan Wilcox via groups.io < dwilcox123@...> wrote:

 
I vote table extension.

Thanks, Dan
Feierabend SM#86

On Wednesday, April 28, 2021, 12:35:13 PM PDT, Mark Garver via groups.io < mgarver@...> wrote:


Greetings! This has been in the front hanging locker and I only saw part of it and had thought it was the small cockpit table. Today, I pulled it out and I have no idea what this is for. The stainless “legs” do not move and look like they are meant to be inserted/installed in something, somewhere. Anyone have the answer?

<IMG_6812.jpeg>
<IMG_6812.jpeg>


 


 


Re: Who can guess what this is

Mark Garver
 

Wow! It is! Thanks! Who knew! 

Mark Garver
S/V It’s Good
SM #105

On Apr 28, 2021, at 3:37 PM, Dan Wilcox via groups.io <dwilcox123@...> wrote:

I vote table extension.

Thanks, Dan
Feierabend SM#86

On Wednesday, April 28, 2021, 12:35:13 PM PDT, Mark Garver via groups.io <mgarver@...> wrote:


Greetings! This has been in the front hanging locker and I only saw part of it and had thought it was the small cockpit table. Today, I pulled it out and I have no idea what this is for. The stainless “legs” do not move and look like they are meant to be inserted/installed in something, somewhere. Anyone have the answer?

<IMG_6812.jpeg>
<IMG_6812.jpeg>


Re: Who can guess what this is

JB Duler
 

Main table extension. But sometimes the table has been "modified" or removed, so thank extension will not fit anymore.
What boat are you on Mark?
--
John Bernard "JB" Duler
San Francisco
Meltem # 19, Western Med

2941 - 2960 of 60605