Date   

Re: Washing machine does not turn on

 

There is an access panel in the port berth. Washer Access Panel in the Port Berth facing forward – upper right. This wood panel has two screws securing it. You will find water and electrical connections here. Photo 5 below shows the panel off and the washer water hose disconnected. Photo 6 is a close-up of what is inside. You will find a 220 AC receptacle inside this area. Sadly, if you are getting power to the receptacle, it is usually the logic board on the washer that has failed. Go to my Amel Book page 279 for washer removal instructions.

image.png
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Tue, May 18, 2021 at 7:00 AM Mohammad Shirloo <mshirloo@...> wrote:

Hi everyone;

 

We’re back on board after 1-1/2 years. Many minor issues resolved. The washing machine does not power on at all, when the 220V  breaker is turned on. Is there a fuse or any other internal component to the washing machine that may prevent it from turning on? Also, where is the access to the electrical connection to the washing machine? I would appreciate any ideas. 

 

Respectfully;

 

 

Mohammad and Aty

B&B Kokomo

Amel 54 #099


Washing machine does not turn on

Mohammad Shirloo
 

Hi everyone;

 

We’re back on board after 1-1/2 years. Many minor issues resolved. The washing machine does not power on at all, when the 220V  breaker is turned on. Is there a fuse or any other internal component to the washing machine that may prevent it from turning on? Also, where is the access to the electrical connection to the washing machine? I would appreciate any ideas. 

 

Respectfully;

 

 

Mohammad and Aty

B&B Kokomo

Amel 54 #099


Re: Eno 4 burner Stove grate and standoffs

Giovanni TESTA
 

Hello Alan,
as I'm not on board, may I have please your new support dimensions (mm) with photo, if possible,
 to better understand "I cut a slot in each side of the U section to match the grating." ?
Many thanks
Giovanni Testa
Venezia
sv EUTIKIA SM428
the boat on the hard at Cleopatra Marina _ Preveza (GR)

Il 22/09/2020 05:53, Alan Leslie ha scritto:
Hi Eric,

I drilled the hole in the bottom of the U section...this is the part that supports the stove top grating. I omitted to say that I cut a slot in each side of the U section to match the grating.
The U section sits on a short piece of stainless tube and the screw goes through the U section through the tube piece and into the stove top.
It replicates the original plastic things that eventually melt.

Like this



Cheers
Alan
Elyse SM437


Re: Passageway berth wall fabric cleaning advice

Paul Guenette
 

Thank you for the advice and tips on cleaning the fabric.

I started first with a 50/50 mix of vinegar applying with a spray bottle. Using a soft brush, I worked it in to the fabric. I then let it set for a couple hours and then used a shop vac to remove a lot of the moisture. I waited till the fabric was totally dry and then I repeated this process.  After  three applications it now looks much better.

I am really grateful for  all the tips and ideas.

Much appreciated, Paul

Aramis
SM 444
Comox, BC, Canada


Re: Furler motor to gearbox sm2000

Michael & Robyn
 

Hi Woody,

are you still seeking the motor brushes for the LS MBT86M motor?
I have ordered my "Brushes .31" x .39" x .7" BRUSH SPR-A007"
from
https://store.eurtonelectric.com/31x31x6brushspr-a005-1-1-1.aspx

I have  a few extra; We are in Christiansted St. Croix in Green Cay Marina, leaving Tuesday.
--
Michael & Robyn

SY RIPPLE SM2K # 417


Re: Depth sensor reading bad values after power cycling

 

Billy,

I said, Speed, but I meant the B&G Depth. The receiver of the DST200 has a very wide range of frequency reception whereas the DST210 is much narrower.

I am thinking you were the victim of interference. Submarine nearby?

Bill
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Mon, May 17, 2021 at 8:26 AM Joerg Esdorn via groups.io <jhe1313=yahoo.com@groups.io> wrote:
Billy, from recollection it is a DST200.  I have not experienced any problems with that transducer (Bill, this is the depth, not the speed transducer).  But the man who would know is Stephane Geniteau, the Amel guy at Pochon.  Pochon installed all electronics on Amel 55s and Stephane did the owner training.   I've found him very responsive.   stephane@....  Good luck.   

Joerg Esdorn
A55 #53, Kincsem
On the hard in Vigo


Re: Depth sensor reading bad values after power cycling

Joerg Esdorn
 

Billy, from recollection it is a DST200.  I have not experienced any problems with that transducer (Bill, this is the depth, not the speed transducer).  But the man who would know is Stephane Geniteau, the Amel guy at Pochon.  Pochon installed all electronics on Amel 55s and Stephane did the owner training.   I've found him very responsive.   stephane@....  Good luck.   

Joerg Esdorn
A55 #53, Kincsem
On the hard in Vigo


Re: SM 2K hull, boot stripe, and rub rail colors

 

The Super Maramu Red Line and the Amel 54 (except for the last 54s produced) have a rub rail and waterline stripe of RAL 3003 Ruby Red.

I do not have the color of the brown rub rail used on most SMs.

Bill
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Mon, May 17, 2021 at 7:34 AM PAOLO CUNEO <pc43ge@...> wrote:
Hi Kent, Iris,
Mine is a  SM Red Line. I have an old note (possibly I took it at Hiėres years ago) that the color code for the rub rail is RAL 3003. I cannot swear on it but I suggest you check it out.
Hope this helps
Fair winds
Paolo Cuneo
SM 454 Whisper
Inviato da iPad

--
Paolo Cuneo
SM 454 Whisper






Re: Rudder moving when anchored - Hy-Drive steering

Michael Brusch
 

Thanks Bill, you answered my question. I have a hydraulic leak and this explains the rudder moving. 


On Sun, May 16, 2021, 9:42 PM Bill Kinney <cruisingconsulting@...> wrote:
Michael,

With hydraulic steering, there is usually no way to stop the problem you are experiencing.  Since there is not a "solid" connection from rudder to wheel, even the tiniest amount of leakage of hydraulic fluid slowly resets the relationship between the wheel and the rudder.

In short, with hydraulic steering there is no way to ensure the rudder and wheel stay in a fixed relationship.

You might be able to lock it in place with something using the emergency tiller connection, but this is a bit inconvenient (at best) and a bit of a kludge.

Bill Kinney
SM#160, Harmonie
Hollywood, FL


Re: SM 2K hull, boot stripe, and rub rail colors

PAOLO CUNEO
 

Hi Kent, Iris,
Mine is a SM Red Line. I have an old note (possibly I took it at Hiėres years ago) that the color code for the rub rail is RAL 3003. I cannot swear on it but I suggest you check it out.
Hope this helps
Fair winds
Paolo Cuneo
SM 454 Whisper
Inviato da iPad

--
Paolo Cuneo
SM 454 Whisper


Re: Depth sensor reading bad values after power cycling

 

Billy,

I assume that you have a sonic speed transducer, rather than a paddle wheel. I have experienced an erratic reading caused when the frequency of something nearby was at the same frequency as the speed transducer receiver. The first time this happened was during a very heavy rainstorm in poorly charted Tonga. I believe that the frequency of the large raindrops pounding the water matched and/or interfered with the frequency of the receiver and the analog instrument dived to zero...wow it was a panic. In 11 years, this only happened twice, both times with a very heavy rainstorm.

Possibly something nearby or a huge rainstorm caused your issue. 

Bill
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Mon, May 17, 2021 at 6:39 AM Billy Newport <billy@...> wrote:
It started working again today. Debris on the transducer?


Re: Depth sensor reading bad values after power cycling

Billy Newport
 

It started working again today. Debris on the transducer?


Re: Rudder moving when anchored - Hy-Drive steering

Bill Kinney
 

Michael,

With hydraulic steering, there is usually no way to stop the problem you are experiencing.  Since there is not a "solid" connection from rudder to wheel, even the tiniest amount of leakage of hydraulic fluid slowly resets the relationship between the wheel and the rudder.

In short, with hydraulic steering there is no way to ensure the rudder and wheel stay in a fixed relationship.

You might be able to lock it in place with something using the emergency tiller connection, but this is a bit inconvenient (at best) and a bit of a kludge.

Bill Kinney
SM#160, Harmonie
Hollywood, FL


Re: Steering wheel removal

 

Eric,

More than you wanted to know:

There are two threaded holes 8mm on either side of the axis. Use the AutoProp Puller and modify it by drilling two 9mm holes spaced 48mm - 63mm apart (it varies). Two 8mm screws are inserted into the new holes of the extractor and screwed into the holes of the wheel. By screwing in the center bolt of the AutoProp Puller, the steering wheel can be removed. 

Note from Steve S/V ALOHA: The older SMs do not have the 2 holes on the wheel for a puller. A technique that works is to have one person sit in the helm seat and pull hard on the wheel with both hands while the other taps on the shaft with a weighted mallet. Make sure to protect the threads on the shaft with the nut. This was recommended by Olivier, and it worked after a few whacks.

image.png
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Sun, May 16, 2021 at 4:02 PM eric freedman <kimberlite@...> wrote:

Hi Bill,

What size are the holes in the prop puller?

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io On Behalf Of CW Bill Rouse
Sent: Friday, March 26, 2021 7:46 PM
To: main@AmelYachtOwners.groups.io Notification <main@amelyachtowners.groups.io>
Subject: Re: [AmelYachtOwners] Steering wheel removal

 

This may help you, especially if you have an AutoProp and AutoProp puller.

image.png

CW Bill Rouse Amel Owners Yacht School

Address: 720 Winnie, Galveston Island, Texas 77550 

 

View My Training Calendar

 

 

On Fri, Mar 26, 2021 at 2:15 PM Slavko Despotovic <slavko@...> wrote:

Hello,

is there easy way to remove the steering wheel on SM. I have removed the part with Henry Amel signature, and removed the screw. From here I do not know as the wheel is firm in place. I do not what break anything so advice will be helpful. Wheel will be send to company that will put new leather  cover.
--
Slavko
SM 2000
#279 Bonne Anse in Portoroz


Re: Furler motor to gearbox sm2000

Teun BAAS
 

Hi Alan,

 

I have the same question; can you cc me when you reply Heinz.

 

Best Regards Teun

SV AMELIT  A54  #128

 

I am in USA

AMELIT is in Storage on the hard in COOMERA (near BRISBANE) QLD AUSTRALIA

May 16, 2021 17:52:42

 

USA cell: +1 832 477 8842

AUSTRALIA cell: +61 5951 8909

 

You can follow AMELIT via this link: https://forecast.predictwind.com/tracking/display/AMELIT

 

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Heinz Stutenbaeumer via groups.io
Sent: Friday, May 14, 2021 01:11
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Furler motor to gearbox sm2000

 

Dear Alan 

My Amel is also in New Sealand. 

Did the New Sealanders let you in? Iff so how did you do that? Can you write me an Mail please 

Thanks 

Heinz SM 2000, 292, SY Quetzal.

 



Am 14.05.2021 um 00:21 schrieb Alan Leslie <s.v.elyse@...>:

With all due respect, Amel didn't "design" the gear train, they only specified it.
Both the Leroy Somer and Bongifoli(?) units are standard production industrial motor gearbox units used in factories for example as conveyor drivers.
They are nothing special.
And there are plenty of alternatives out there.

Cheers 
Alan
Elyse SM437
On my way to New Zealand today to be reunited with my beautiful boat after more than a year !


Re: Steering wheel removal

Eric Freedman
 

Hi Bill,

What size are the holes in the prop puller?

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: main@AmelYachtOwners.groups.io On Behalf Of CW Bill Rouse
Sent: Friday, March 26, 2021 7:46 PM
To: main@AmelYachtOwners.groups.io Notification <main@amelyachtowners.groups.io>
Subject: Re: [AmelYachtOwners] Steering wheel removal

 

This may help you, especially if you have an AutoProp and AutoProp puller.

image.png

CW Bill Rouse Amel Owners Yacht School

Address: 720 Winnie, Galveston Island, Texas 77550 

 

View My Training Calendar

 

 

On Fri, Mar 26, 2021 at 2:15 PM Slavko Despotovic <slavko@...> wrote:

Hello,

is there easy way to remove the steering wheel on SM. I have removed the part with Henry Amel signature, and removed the screw. From here I do not know as the wheel is firm in place. I do not what break anything so advice will be helpful. Wheel will be send to company that will put new leather  cover.
--
Slavko
SM 2000
#279 Bonne Anse in Portoroz


SM 2K hull, boot stripe, and rub rail colors

karkauai
 

Hi Amelians,
Our boat yard lost the colors we picked out last Fall.  Our rail and bootstripe have been primed, so nothing to compare to. I want to use awkgrip on the hull and bootstripe, and Awlcraft on the rail.
I've searched the site and found that some have used Awlgrip Eggshell on the hull. Is that a close match to the original? 
We don't want to use the Desert Sand on the bootstripe.  
It looks like either International Orange or Vermilion would be pretty close. Any other thoughts on that?

I see Steve used a Trojan battery to custom mix a rub rail
color.  Has anyone used a stock color that is very close to the otiginal? We have the new offwhite gutter cap if that makes any difference.

Thanks for any insight.
Kent & Iris
KRISTY
SM243
Sailing from Chesapeake to Maine for the Summer.


Rudder moving when anchored - Hy-Drive steering

Michael Brusch
 

Hi guys, I have an Amel Maramu, which has been retrofitted with a hydraulic steering system (Hy-drive) (The original cable steering system was disconnected and left in place). When anchored and when current or waves are present, the rudder seems to move on its own all the way to port, thus knocking the hull right under my bed. Sometimes at night I would go out and bring the steering wheel al the way over to starboard, which gives me a few hours until the rudder is back all the way to port.

My question: Is there a way to keep the rudder from moving independently? I tried fixing the wheel in place, but this does not seem to do anything. I am so frustrated that I am considering going back to cable steering. I have also been thinking of installing a Hydrovane system in which case I want to make sure that the rudder stays centered when sailing.

Thank you for your input :)


Re: Depth sensor reading bad values after power cycling

Bill Kinney
 

Airmar transducers all come with a tag on the wire close to the transducer with detailed part information. It's worth a look to see if it is still there...


Re: overhead insulation and headliner

marklesparkle59
 

Sea Hobos linings were replaced with 5mm of foam and finished off with the type of carpet you find on camper vans. Definitely more insulating and brighter than the broken down foam backed vinyl which had lasted for 30 years.
Mark Porter
Sea Hobo. Sharki #96
Currently in Cawsand Bay UK

2641 - 2660 of 60592