Date   

Re: [Amel] Leaving forum

Zanareva
 

Giovanni,
No, thank you. Success of this group is the result of all the great owners aboard contributing really good information. I've 99.999% of the time stayed in the background!
Best regards,
Richard

--- In amelyachtowners@yahoogroups.com, "Giovanni Testa" <gtesta23@...> wrote:

Hi Richard,
thanks so much for your support , always very prompt and rich of suggestions. Now I know better the great Amel people around the world also thanks to you.
All the best and...Buon Vento !
Giovanni TESTA
s/v EUTIKIA
SM2K n428
----- Original Message -----
From: closereach
To: amelyachtowners@yahoogroups.com
Sent: Thursday, October 29, 2009 10:51 PM
Subject: [Amel] Leaving forum


I'll also be leaving the forum and relinquishing any site management functions. Want to say thanks to Jose Luis for his active moderation for the past several years--I'm sure he'd like for another Amel owner to step up and volunteer to help him out!
All the best to all of you and fair winds,
Richard







Re: Leaving forum

Zanareva
 

John,

Thanks for the kind words. We've enjoyed our two Amels over the years, first a Sharki and now a Super Maramu, and getting this forum started.

As a bit of history, on May 23, 2001 Amel sent an email to all owners apologizing for a virus that they may have inadvertently included in an email communication (don't know what that was about since I did not receive it). Fortunately for all of us, Amel put every owner's email address that they had a record of in the "TO" heading (rather than using a blind carbon copy, or "BCC"). I remember I had been trying to convince the factory to get some sort of owner's club or association started, even chatting with Joel about it, but with no effect--so getting a copy of everyone's email address easily lead to the next step of starting this group on Yahoo.

All the best,
Richard

--- In amelyachtowners@yahoogroups.com, " Anne and John Hollamby" <annejohnholl@...> wrote:

Dear Richard, Very sorry to see that you are selling your SM and leaving the forum. Many thanks for all the work you have done over the years and especially, if I remember correctly for creating the web site in the first place and moderating it so well over the years.
Thanks again and all the best in the future. Best wishes, John Hollamby, SM 319 Bali Hai.
----- Original Message -----
From: closereach
To: amelyachtowners@yahoogroups.com
Sent: Thursday, October 29, 2009 10:51 PM
Subject: [Amel] Leaving forum


I'll also be leaving the forum and relinquishing any site management functions. Want to say thanks to Jose Luis for his active moderation for the past several years--I'm sure he'd like for another Amel owner to step up and volunteer to help him out!
All the best to all of you and fair winds,
Richard







Re: [Amel] heating system

joseph mc donnell
 

We had a similar problem on our santorin, getting noxious fumes when the heater was on. I found that it was not the heater causing the problem, but that the internal coating of the box containing the heater appeared to be in the process of breaking down. This tar appears to be oil based and it gives of droplets of oil which I found attached to the fireproof insulation of the heater exhuast. When the heater was turned on, the exhaust then heated up the droplets, which gave of fumes, which were then in turn sucked through the fresh air inlet of the heater and on into the cabins. You can easly find out if this is the problem by watching the exhaust heat up to see if it gives of fumes. I scraped of as much of the internal coating as I could and replaced the insulation on the exhaust. There was a marked improvement.
Regards Joe McDonnell

amelyachtowners@yahoogroups.com, Richard Piller <richard03801@...> wrote:


if you are getting fumes in the aft cabin STOP using the heater. Open up the cover and make sure the exhaust pipe is properly attached and check it all the way to the exit. Be sure there is nothing block the exit hole. Then check to be sure the metal pipe on the hot air side of the heater is connected properly.. you should never get fumes from the oil burner...
Richard and Joan on Challenge




________________________________
From: spritoaffine <spritoaffine@...>
To: amelyachtowners@yahoogroups.com
Sent: Thu, October 29, 2009 8:53:00 AM
Subject: [Amel] heating system


Hello All
Can anyone help with information regarding the heating system on the Sharki?

We have a separate fan and hose system mounted on the same chassis as the heater and connected to a diverter valve alongside the Eberspacher. Running the heater alone has filled the aft cabin with noxious fumes, am I supposed to run the 2nd fan at the same time as the heater or is this nothing to do with the heater system?
David and Hazel
Spirito Affine
Sharki 148









Out haul motor

Dimitris Krassopoulos <dkra@...>
 

I had a problem with the outhaul motor. It is attached to the boom through 4
screws that keep also the cover of the gear in place. In case you take in
the sail and the car hits the end of the track the whole motor is moving
sideways and can easily shear off the screws. I had the problem two times
until now. Are also other fellow SM users have the same problem? I will try
to solve the problem with a cover fixed on the boom.



Dimitris

SM 2000 Alma Libre


Re: [Amel] Leaving forum

Giovanni TESTA
 

Hi Richard,
thanks so much for your support , always very prompt and rich of suggestions. Now I know better the great Amel people around the world also thanks to you.
All the best and...Buon Vento !
Giovanni TESTA
s/v EUTIKIA
SM2K n428

----- Original Message -----
From: closereach
To: amelyachtowners@yahoogroups.com
Sent: Thursday, October 29, 2009 10:51 PM
Subject: [Amel] Leaving forum


I'll also be leaving the forum and relinquishing any site management functions. Want to say thanks to Jose Luis for his active moderation for the past several years--I'm sure he'd like for another Amel owner to step up and volunteer to help him out!
All the best to all of you and fair winds,
Richard


Electric Bowthruster

nomadforpaul <pflafrance@...>
 

We are currently repairing our Bow Thruster Motor. The unit is made by Leroy Somers. The bottom bearing has to be replaced as we believe water damaged same. Does anyone have a schematic of the unit or where one might find one. Does anyone know where to order parts from in the US?

Thanks
Paul
S/V NOMAD SM #362


Re: [Amel] Leaving forum

Anne and John Hollamby <annejohnholl@...>
 

Dear Richard, Very sorry to see that you are selling your SM and leaving the forum. Many thanks for all the work you have done over the years and especially, if I remember correctly for creating the web site in the first place and moderating it so well over the years.
Thanks again and all the best in the future. Best wishes, John Hollamby, SM 319 Bali Hai.

----- Original Message -----
From: closereach
To: amelyachtowners@yahoogroups.com
Sent: Thursday, October 29, 2009 10:51 PM
Subject: [Amel] Leaving forum


I'll also be leaving the forum and relinquishing any site management functions. Want to say thanks to Jose Luis for his active moderation for the past several years--I'm sure he'd like for another Amel owner to step up and volunteer to help him out!
All the best to all of you and fair winds,
Richard


Leaving forum

Zanareva
 

I'll also be leaving the forum and relinquishing any site management functions. Want to say thanks to Jose Luis for his active moderation for the past several years--I'm sure he'd like for another Amel owner to step up and volunteer to help him out!
All the best to all of you and fair winds,
Richard


Our 1989 Super Maramu is for sale

Zanareva
 

Circumstances require us to sell our Amel. Located in Satellite Beach, Florida. Email me for detailed interior/exterior photos and equipment list. $249K
Richard
closereach "at" yahooooooooooooo.com


Re: Floor locker latches

karkauai
 

Thanks Richard and Joan,
I wasn't planning to run out and buy those latches, but it's sure nice to be able to get info like that without having to research it yourself. I'm feeling better now about the trip South, and am planning to recharge and swap crew in Bermuda before heading to the BVI, then a couple days in BVI to recharge and repair anything that gets broken before heading south to Granada. I've got things pretty much ready to go now, just need to learn the SSB/Pactor Modem and internet access via the satphone. Thanks for your encouraging words and advice.
Kent
SM243 "Kristy"


Re: [Amel] Re: Floor locker latches

Richard Piller <richard03801@...>
 

Kent, we have done a lot of ocean work with our SM 209 (32000 miles) we have NEVER had an issue with floor boards. Pardon me but those guys doing the safety checks for the 1500 are as much interested in safety as they are in how much you spend to follow their advice. We have been in 35 foot waves and 60+ kts without an issue with the floor boards. Kent when the wind is up the first sail that comes down/rolls up is the main. Don't try to run in a big beam sea way bear off or run or for that matter just heave to and wait it out...
Take to time to stop at St Georges in Berumda. Relax for a day or two fuel up water up. Go in during day light call Bermuda radio when you are 15 miles out they are a big help.. Call Southbound 2 on the SSB check in time is 1930 utc. Tell him you boat name and destination the first time you call (call several times between 1930 adn 1950 listen for him to call your boat name if he doesn't call again on q. then check in every day without fail..

You'll be fine... oh, when you leave Bermuda say well east of the line south to the Bahamas or Caribb. the winds and current will push you west just fine...
Richard and Joan on Challenge.


________________________________
From: Kent Robertson <karkauai@yahoo.com>
To: amelyachtowners@yahoogroups.com
Sent: Wed, October 28, 2009 11:06:18 AM
Subject: [Amel] Re: Floor locker latches


You guys are soooooo good! Thanks,
Kent
SM243 "Kristy"

--- In amelyachtowners@ yahoogroups. com, David Mackintosh <dlm48@...> wrote:

easily found

http://www.pyiinc. com./index. php?section= panel_anchor& action=main& sn=2

regards

David

2009/10/28 Bob Linley <bob@...>


Re: [Amel] heating system

Richard Piller <richard03801@...>
 

if you are getting fumes in the aft cabin STOP using the heater. Open up the cover and make sure the exhaust pipe is properly attached and check it all the way to the exit. Be sure there is nothing block the exit hole. Then check to be sure the metal pipe on the hot air side of the heater is connected properly.. you should never get fumes from the oil burner...
Richard and Joan on Challenge




________________________________
From: spritoaffine <spritoaffine@yahoo.co.uk>
To: amelyachtowners@yahoogroups.com
Sent: Thu, October 29, 2009 8:53:00 AM
Subject: [Amel] heating system


Hello All
Can anyone help with information regarding the heating system on the Sharki?

We have a separate fan and hose system mounted on the same chassis as the heater and connected to a diverter valve alongside the Eberspacher. Running the heater alone has filled the aft cabin with noxious fumes, am I supposed to run the 2nd fan at the same time as the heater or is this nothing to do with the heater system?
David and Hazel
Spirito Affine
Sharki 148


heating system

spritoaffine <spritoaffine@...>
 

Hello All
Can anyone help with information regarding the heating system on the Sharki?

We have a separate fan and hose system mounted on the same chassis as the heater and connected to a diverter valve alongside the Eberspacher. Running the heater alone has filled the aft cabin with noxious fumes, am I supposed to run the 2nd fan at the same time as the heater or is this nothing to do with the heater system?
David and Hazel
Spirito Affine
Sharki 148


Re: [Amel] Maramu Prop

Eric Lindholm <etlindholm@...>
 

Any prop shop should be able to help you. I would think the yard would be able to suggest one. That does not sound like the right size prop. I think it should be a 19/17, assuming your gear reduction is 2.74 to 1. You may have a different reduction, ie 2.5 to 1 which would require the reduced pitch. You need to provide the prop shop with the hp 60, the gear reduction, and the shaft size, probably 1 3/8. Eric maramu 105




________________________________
From: rfmolony <rfmolony@gmail.com>
To: amelyachtowners@yahoogroups.com
Sent: Wednesday, October 28, 2009 7:41:15 PM
Subject: [Amel] Maramu Prop

 
Gentlemen (and Ladies),

Amel Maramu Hull 91, "Popeye" is up on the hard having the bottom done, but when the prop was pulled for repair, it became apparent that electrolysis had done a number on it and it would need to be replaced. The yard are unable to find a replacement through their usual channels.

I understand it is a 19 x 14, standard 35mm taper. Assuming this is the right prop for a Maramu with a Prima M60 (Perkins 4:154?), does anyone know where I may be able to obtain one in the US, or for that matter, anywhere?

Any assistance would be greatly appreciated, given the boat is sitting there, and if time drags on I will be committed to hauling again later to perform the prop change.

Richard Molony




[Non-text portions of this message have been removed]


Maramu Prop

rfmolony <rfmolony@...>
 

Gentlemen (and Ladies),

Amel Maramu Hull 91, "Popeye" is up on the hard having the bottom done, but when the prop was pulled for repair, it became apparent that electrolysis had done a number on it and it would need to be replaced. The yard are unable to find a replacement through their usual channels.

I understand it is a 19 x 14, standard 35mm taper. Assuming this is the right prop for a Maramu with a Prima M60 (Perkins 4:154?), does anyone know where I may be able to obtain one in the US, or for that matter, anywhere?

Any assistance would be greatly appreciated, given the boat is sitting there, and if time drags on I will be committed to hauling again later to perform the prop change.

Richard Molony


Re: Floor locker latches

karkauai
 

You guys are soooooo good! Thanks,
Kent
SM243 "Kristy"

--- In amelyachtowners@yahoogroups.com, David Mackintosh <dlm48@...> wrote:

easily found

http://www.pyiinc.com./index.php?section=panel_anchor&action=main&sn=2

regards

David

2009/10/28 Bob Linley <bob@...>


Re: [Amel] Floor locker latches

john martin <symoondog@...>
 

Danny, I wouldn't worry too much about securing those floor hatches if I were you. It would take one hell of a storm with hugh waves to turn a SM completely upside down (a 360 degree roll) I don't know of any boat in all the years of the Caribbean 1500 that has ever been completely rolled over. I just finished circumnavigating South America and I didn't secure the hatches. Just my opinion
John "Moon Dog" SM 248


To: amelyachtowners@yahoogroups.com
From: simms@xtra.co.nz
Date: Wed, 28 Oct 2009 12:40:05 +0000
Subject: [Amel] Floor locker latches





Hi All
We are going offshore and want to secure the floor lockers. We have seen two types of latch, one that requires a fairly large hole to be cut in the lid to fit it, the other screws flat on the surface. Same type of operation, but easier to fit. Any suggestions where we can get these. We are in Hampton Virginia departing in the Carib 1500 on the 2nd Nov
Danny and Yvonne SM 299 Ocean Pearl









_________________________________________________________________
New Windows 7: Find the right PC for you. Learn more.
http://www.microsoft.com/windows/pc-scout/default.aspx?CBID=wl&ocid=PID24727::T:WLMTAGL:ON:WL:en-US:WWL_WIN_pcscout:102009


Re: [Amel] Floor locker latches

David Mackintosh <dlm48@...>
 

easily found

http://www.pyiinc.com./index.php?section=panel_anchor&action=main&sn=2

regards

David

2009/10/28 Bob Linley <bob@bourlet.com>



Danny

Last year when we did the Carib 1500 the safety inspectors were all over us
about the floor lockers. I tried putting one in the 1st locker and although
I have reasonable carpentry skills it was an abortion. I abandoned the idea
after talking to another Amel in the Rally (Jorge on Excalibur)and we
decided that if a storm was heading our way we would put in a few discrete
screws.

Sorry I could not join all the Amels in this year's Rally, it would have
been a great sight. I will be keeping tabs on the internet. Our plans are
now for the Med in June.

Good luck and good cruising.

Bob

s/v Minaxi SM6

From: amelyachtowners@yahoogroups.com <amelyachtowners%40yahoogroups.com>
[mailto:amelyachtowners@yahoogroups.com<amelyachtowners%40yahoogroups.com>]
On Behalf Of simms@xtra.co.nz <simms%40xtra.co.nz>
Sent: Wednesday, October 28, 2009 8:40 AM
To: amelyachtowners@yahoogroups.com <amelyachtowners%40yahoogroups.com>
Subject: [Amel] Floor locker latches

Hi All
We are going offshore and want to secure the floor lockers. We have seen
two
types of latch, one that requires a fairly large hole to be cut in the lid
to fit it, the other screws flat on the surface. Same type of operation,
but
easier to fit. Any suggestions where we can get these. We are in Hampton
Virginia departing in the Carib 1500 on the 2nd Nov
Danny and Yvonne SM 299 Ocean Pearl






Re: Suggestion on Super Maramu

Miles Bidwell <mbidwell@...>
 

Last year my wife and I sailed our Super Maramu back to the US from Europe
after spending 8 years in the Med. The Amel has a very powerful bow
thruster and we had no difficulty maneuvering in ports. With the bow
thruster one can drive the boat like a car, but unlike a car, one can move
sideways by using the rudder and bow thruster together. In a cross wind in
port, the Amels appeared to maneuver better than most other boats of any
size.



Cheers,

Miles

LADYBUG (sm 216)


Re: [Amel] Floor locker latches

minaxi53
 

Danny

Last year when we did the Carib 1500 the safety inspectors were all over us
about the floor lockers. I tried putting one in the 1st locker and although
I have reasonable carpentry skills it was an abortion. I abandoned the idea
after talking to another Amel in the Rally (Jorge on Excalibur)and we
decided that if a storm was heading our way we would put in a few discrete
screws.

Sorry I could not join all the Amels in this year's Rally, it would have
been a great sight. I will be keeping tabs on the internet. Our plans are
now for the Med in June.

Good luck and good cruising.

Bob

s/v Minaxi SM6



From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of simms@xtra.co.nz
Sent: Wednesday, October 28, 2009 8:40 AM
To: amelyachtowners@yahoogroups.com
Subject: [Amel] Floor locker latches





Hi All
We are going offshore and want to secure the floor lockers. We have seen two
types of latch, one that requires a fairly large hole to be cut in the lid
to fit it, the other screws flat on the surface. Same type of operation, but
easier to fit. Any suggestions where we can get these. We are in Hampton
Virginia departing in the Carib 1500 on the 2nd Nov
Danny and Yvonne SM 299 Ocean Pearl