Date   

Re: B&G Sonic Speed sensors replacement

Gary Silver
 
Edited

Hi Michele: 

I will echo what Jason Rutledge posted and perhaps amplify the procedure.  I provided about a dozen photos to Bill and perhaps he will post them if he hasn't done so already..  Jason and I did this job together.  It is a two person job.  

The sensors and cables run in smooth plastic chases (pipes) from their position below the waterline to a position above the waterline so no sealing is necessary.  Our sensors (SM Hull # 335) were not sealed in any way, however, they are a loose interference fit in their recesses/counter-bores.  I have been told by Bill that some were sealed with 3M 5200 or other type sealant.  The plastic wire chase for the forward sensor comes up just in front of the forward seat of the saloon table.  The wire exits the chase at this point, makes a "U" turn and re-enters a chase that goes to starboard, enters a fiberglass chase that end in the cabinet where the sonic speed computer is located (next to, and forward of the starboard side fore-aft saloon seat).    The rear sensor, that is on the leading edge of the stub keel has a chase that appears in the aft, under-table, athwart-ship locker beneath the saloon table.  It is encased in a semi-clear hose that takes it further above waterline and enters the same fiberglass chase that takes the cable to the computer.    It is easiest to remove this hose at the fixed chase in the under-table locker so you are only working with 2-3 feet (1 meter) of cable.  

Start by identifying the routing of both cables.   Next, remove (gently pull on) the 1/2 in (1.5cm) long rubber covering of the transducers at the hull forward and aft transducer positions.  You will find underlying those rubber transducer covers a ceramic like plastic face of the actual sonic transducer.  The  rubber acts  as a protectant "sonic coupling".   Use a drill to gently and patiently drill a small hole in the face of the transducer to a depth of about 1/2 inch.  Into that hole thread an appropriately sized sheet metal screw (coarse thread) such  that it has good grip on the coupling but doesn't fracture it or expand it creating excess drag.  Next, while a person inside the boat pushes on the transducer cable (close to the chase so as to exert pressure on the cable without kinking it), gently and patiently pull on the previously inserted screw in the transducer to extract it from its counterbore (recess).   In our case these slid out with minimal traction.  There was no evidence of marine growth or other "cementing" adhesives.  The blunt end of the chase tube is positioned such that it provides a shoulder for the counter-bore that exactly positions the transducer so that it CANNOT be seated too deeply into the recess.  Exact distance between the transducers is important and has been expertly calculated by Amel.  

You use the old cable as a messenger line to pull the new wire into place.  In our case I cut off the old transducer, stripped a small section of cable cover and I soldered the wires of the old and new together.  It takes minimal traction to pull the new wire into place.   I lubricated the new transducer and counter-bore with silicone grease and it slid into place easily.   I WOULD NOT SEAL THIS TRANSDUCER WITH ANY KIND OF SEALANT AS IT ISN'T NECESSARY AND WILL ONLY MAKE THIS TASK MORE DIFFICULT IF IT NEEDS TO BE REPEATED IN THE FUTURE.  AGAIN, the chases ends above waterline and there is no need to seal the transducers.  Thread the respective cables thru their respective hose and/or chase to the computer making sure you somehow label them as fore and aft (as this will be required for proper connection).  Use the old cables as messenger lines  Cut the cables long enough to have a proper service loop (copy what Amel did).  Strip the insulation and extract the wires from the shielding.  Attach at the computer in the same manner as previously.  See the information in the files section for setting the dial in the computer for illumination of the calibrating red LED.  Calibration is also done on the B & G Multi-function display at the nav station (instructions in the installation manual for that unit as provided by Amel).    If you have any questions don't hesitate to email me at garysilver at mac dot com.  

This was a relatively easy job that I had dreaded (unnecessarily it turns out) for years.  You need someone to push/feed and someone to feed/pull at the same time, hence the two person job.   There is a bunch of information in the photos section and the files section on the Sonic Speed.  I did trim the rubber coupler fair with the face of their hull and keel faces (at a more marked angle for the keel coupler) by gently slicing with a razor blade.  Try to make a smooth cut.   Also read this:  https://amelyachtowners.groups.io/g/main/files/B%20&%20G%20Sonic%20Speed%20Information/SonicSpeedTroubleshooting.pdf

All the best, 
Gary S. Silver, M.D.,  Farmington, UTAH,  USA
former owner of s/v Liahona (from new to age 20 years)    Amel SM 2000 # 335   now owned by Jason Rutledge


Gas struts for cockpit access

Ron Hynes
 

The gas struts that assist opening the cockpit floor and holding the hatch open are seriously deteriorated on my boat. Rather than reinvent the wheel, I was wondering if anyone has found a source and knows the specs for these struts.  I have an older Meltem, but I’ve seen the cockpit access up through super maramus and they are pretty much the same.


Re: Tinkling Sound

Paul Harries
 
Edited

This sounds like a high frequency resonance issue.
With high frequency I would suspect a small component attached to something larger that catches the wind.
If you touch the offending item sound should disappear
If I were you I would check in following order
Tension in shrouds
All turnbuckles, shackles and pins including contact with spreaders.
If nothing found change tension in halyards one at a time to see if sound changes, if it changes check all tackle that halyard in contact with. 
Also consider touching electrical cables from mast in ceiling one at a time, if sound vanishes you have identified source.
Remember if you touch stethoscope to offending item you will change resonant frequency and sound will disappear.
 
One other possible cause is internal partial failure of one of standing rigging cables with broken strands.
 
All this being said don't forget the obvious. I once saw a patient complaining that his implanted neurostimulator was playing music. Turned out his phone had butt dialed a bahamas number and he had been hearing hold music from his jacket pocket! The two hour international call was fairly expensive!

 

On Sun, Sep 19, 2021 at 9:31, karkauai via groups.io
<karkauai@...> wrote:
OK, This is a bit difficult for me, as my ears are so bad that I can't hear it, but it's driving Iris to distraction.  It just started a week or so ago, and nothing had changed except we anchored in Woods Hole, MA, USA.  It's still present on a mooring in Martha's Vineyard.  At anchor, when the wind is up and the boat is moving, she hears a very high pitched tinkling, like wind chimes made of glass. It is constant in higher wind, intermittent in less wind, and all but disappears in light winds. It doesn't seem to match the rhythm of the boat's movement, but as the wind picks up and the boat moves more it gets louder.  It seems to be louder in the area of the forward head, but difficult to pinpoint.  She can't hear it on deck or in the cockpit.  Using a stethoscope on the masts, booms, bulkheads, and decking hasn't helped, in fact she can't hear it at all when using the stethoscope.  So it seems to be transmitted by air rather than water & hull...except that she hears it in the boat and not on deck.  It's not like shrimp or crustations, more musical.

We're stumped.  She suggests the possibility of a ghost ship with wind chimes.  I've suggested maybe it's all in her head (but her description doesn't sound like tinnitus).

Anyone else experience anything like this?  Any ideas?

Thanks

Kent & Iris
KRISTY
SM243
Heading S to Chesapeake.

--
Paul Harries
Prospective Amel Buyer


Re: Amel 55 Hardtop & Mainsheet question

Joerg Esdorn
 

For what it’s worth, the boat I test sailed in 2015 had the main sheet go to the mizzen mast, as does my boat.  There is a risk with that arrangement that the sheet will wrap around the corner of the roof if the extension is pulled out.  I avoid that by using the bingos you can see in this picture.  The bungee pulls the main sheet forward of the corner if there is little tension on the sheet like in a light air jibe.  

Joerg Esdorn
A55 #53 Kincsem
Currently in Trinite sur Mer


Tinkling Sound

karkauai
 

OK, This is a bit difficult for me, as my ears are so bad that I can't hear it, but it's driving Iris to distraction.  It just started a week or so ago, and nothing had changed except we anchored in Woods Hole, MA, USA.  It's still present on a mooring in Martha's Vineyard.  At anchor, when the wind is up and the boat is moving, she hears a very high pitched tinkling, like wind chimes made of glass. It is constant in higher wind, intermittent in less wind, and all but disappears in light winds. It doesn't seem to match the rhythm of the boat's movement, but as the wind picks up and the boat moves more it gets louder.  It seems to be louder in the area of the forward head, but difficult to pinpoint.  She can't hear it on deck or in the cockpit.  Using a stethoscope on the masts, booms, bulkheads, and decking hasn't helped, in fact she can't hear it at all when using the stethoscope.  So it seems to be transmitted by air rather than water & hull...except that she hears it in the boat and not on deck.  It's not like shrimp or crustations, more musical.

We're stumped.  She suggests the possibility of a ghost ship with wind chimes.  I've suggested maybe it's all in her head (but her description doesn't sound like tinnitus).

Anyone else experience anything like this?  Any ideas?

Thanks

Kent & Iris
KRISTY
SM243
Heading S to Chesapeake.


Re: Lithium Battery BMS

Willem Kroes
 

Juan,


I bought 8 Lithium Iron Phosphate batteries (LifePO4) of 100 Ah at 12V with built-in BMS modules from Shenzen Yinkai Power Technology Co., Ltd. Website: www.yinkaipower.com.

These batteries were/are almost drop-in replacements. Almost, because they are a little higher than the lead-acid batteries Amel used. Dimensions: 329 x 171 x 235 mm. I had to cut off a few millimeters from the bar under the lid of the battery compartment (the bar that prevents upward movements of the batteries).

I paid by the end of 2016 USD 4.373 for the 8 batteries plus 2 extra BMS plus 2 extra empty cases excluded VAT and import duties, but shipping cost included. Since then prices have gone down. I don’t know if Yinkai Power is still selling the 100 Ah battery, but there are a lot of other companies in the Shenzen area to sell these. For example: Polinovel 12v 100ah lithium ion battery manufacturer.


Best regards,


Willem Kroes

SM #351 Kavanga

Now in Licate on Sicily


Re: Shore - Generator Switch-over box on A54 #solution

Rudolf Waldispuehl
 

Hello Mohammad

 

This is a lot of Inverting power. You probably not need that much unless you want to run everything simultaneously in the boat 😉

Nevertheless, I ordered the MV MassCombiPro 24/3500W since I have already 2 Solar controllers separately and do not need in the same box.

Queston:

Did you installed the MV Mass Combi Ultra 24/3500 at the same place/pedestal where the 2500W inverter was? Or you found another place?

                - I’m asking because the installation manual says it should be installed vertical and the existing A54 inverter pedestal is somehow more horizontal then vertical.

I guess you use it as 2500W inverter replacement and not for charging? So probably no issue with the ventilation so far?

 

Thanks for advice and best regards

Ruedi Waldispuehl

WASABI A54. #55

Currently in Gibraltar

 

Von: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io> im Auftrag von Mohammad Shirloo <mshirloo@...>
Antworten an: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Datum: Sonntag, 19. September 2021 um 10:45
An: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Cc: Ian Fraser <keyproperties@...>
Betreff: Re: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Hello Ian;

 

My knowledge of the LN175 and Dolphin charger is limited, so I will not be of much help there. I can share with you our current approach for our charging and inversion plans, as we make the necessary upgrades, as equipment fails.

 

Our 2500W Mastervolt inverter failed at the end of the 2019 season. We would like to use the existing charger wiring in the engine room. We have replaced our inverter with a MV Mass Combi Ultra 24/3500. These inverter /chargers can charge at 100A, provide 3500W 220V and have solar controllers built in. They can also be connected in series for additional charging and inversion output. We intend to have 2 in series, giving us 200A charging/7000 W inversion. We will still have our existing 40A MV charger, for a total of 240A charging. I have not checked the existing 40A charging wiring size. It is possible to add a third combi Ultra for  max of 300A charging and 10,500W of inversion. The Combi Ultra can also be programmed to limit the charge/inversion output to match the wiring size. The plan is to be able to supply the entire 220V panel from the inverters.

 

We have not gone far down the design phase, as this is some time away for us. However, I like the small size (same appx footprint as the inverter we replaced) and light weight of  combi/ultra. We should be able to fit 2 and possibly three in the same footprint and location of the existing chargers. Minimal wiring and full integration, monitoring and control of the Lithium batteries, chargers, inverters and solar.

 

All of this is very preliminary. In the next 2-3 years that it will take for us to be ready to make the upgrade, I’m sure may thing have changed  that will require changes to our basic design concept.

 

Respectfully;

 

 

Mohammad and Aty

B&B Kokomo

Amel 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Ian Fraser via groups.io
Sent: Friday, September 17, 2021 2:16 PM
To: main@amelyachtowners.groups.io
Cc: Ian Fraser <keyproperties@...>
Subject: Re: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Mohammad,

 

Thank you for your insights on Lithium. We are in a similar situation and agree that Lithium is too early for us.

 

Will really appreciate your guidance on best solutions for changes to LN175 alternator (and Dolphin 100A Charger) when upgrading to 8AGM 105Ahr on AMEL54 #009.

Regards,

Ian Fraser
Dreamtime.   

On 17 Sep 2021, at 03:27, Mohammad Shirloo <mshirloo@...> wrote:

 

Hi Ruedi;

 

We are currently in the Med and, in my opinion,  Lithium is not a huge advantage in our cruising style here. Also our AGMs that we installed in 2018, have been working better than expected and almost as good as when installed new.

 

I believe that Lithium technology for yachts is in its infancy and the improvement curve fairly steep. Our plan is to convert to Lithium in about 2-3 years, before leaving the Med, so we can benefit from all the advancement in technology and safety. 

 

Respectfully;

 

 

Mohammad and Aty

B&B Kokomo

Amel 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Rudolf Waldispuehl via groups.io
Sent: Thursday, September 16, 2021 11:28 PM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Hi Mohammad and Aty

 

Thank you for the drawing which helped me a lot. Exactly this page was not in my documentation. Don’t know why?

I found in the 220V Panel drawing K1- and K2-source referenced, but without any detail about K1 and K2. Now everything is very clear and you are absolutely right with the priorities.

 

  • When there is Power from the Generator, K1 is interrupting the Shore supply and switching to Generator with the K1 Relay.
  • When there is any Power from any K1 source (GE or Shore), K2 is active and the Inverter is not switched because K2 is keeping the Inverter 220V output unswitched (offline).
    • Even if the inverter is ON, it can’t deliver 220V to the panel, because K2 is ON as long as K1 delivers power.

 

This sound a bit complicated but it’s finally the priority GEN, Sore, Inverter as you said.

 

BTW: What is your Lithium Project doing? You have changed KOKOMO to Lithium meanwhile?

 

Thanks and fair winds

Ruedi & Sabina Waldispuehl

"SY WASABI"

Amel 54. #55

Currently in Estepona heading to Gibraltar

 

 

Von: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io> im Auftrag von Mohammad Shirloo <mshirloo@...>
Antworten an: "
main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Datum: Donnerstag, 16. 
September 2021 um 07:40
An: "
main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Betreff: Re: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Hi Ruedi;

 

There are electrical schematics in the original AMEL operator’s manual in the Appendix section, that came with the yacht, that show how they are wired. Attached is the schematic for the K1-K2 switchover relays.

 

I believe K1 and K2 switch/relays make the selection of power source.  Power first  goes through K1 which selects the source between shore power and generator. I believe that generator has priority over shore power. Once this source is selected, it goes through K2, which selects between the output of K1 and the inverter, with the output of K1 having higher priority.

 

I am fairly certain that the priority is: 

 

  1. Generator
  2. Shore power
  3. Inverter

 

Respectfully;

 

 

Mohammad and Aty

B&B Kokomo

Amel 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Rudolf Waldispuehl via groups.io
Sent: Wednesday, September 15, 2021 8:31 PM
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Hello Amelian's

 

I tried to find out how the Shore/Generator Switchover Box in the Engine room of my Amel-54 is exactly working. I do have in addition a 2500W MV inverter installed originally from AMEL. Last few weeks the Switch-over is doing strange things and fuses are blowing. 

 

I have not found any accurate information (drawings) electric scheme of that AMEL specific switch-over mechanism. I don’t know how it detects either one or all 3 of the 240V sources, and which is the master over-ruling the Generator or Shore and/or Inverter. How it protects the Inverter when Shore or Generator is running, etc… 
Does anyone out there have any detailed information how these system works and may have an Electric scheme with in dept knowledge how it works?

 

Thanks a lot for investigation and best regards
Ruedi Waldispuehl
WASABI 

WASABI A54. #55

E-MAIL: mail@...

 


Re: B&G Sonic Speed sensors replacement

Marco Mancini
 

Dear Michele we did last year because our probe failed and I have tried with success  to replace the older one instead to put a new probe for several  reasons  . We  replaced ( my sailor man didi)  both the sensors  because we had to buy for about 300 US $ .  The cables run into a dedicated pipelines ( you may  easily see upper part of the one relative to the probe that look forward ) just in the compartment below the table dinette where you will see the cable inside a transparent pipe.  
 You can exract the probe and cable from the housing in the keel using a witness cable  and insert the new one pulling the witness cable from inside. You need to seel the probe in the keel with neoprene .  Check that the reading geometry of the front and rear probe is the same. 
I hope this may help 
sincerely 

Marco Mancini

Il giorno 09 set 2021, alle ore 20:09, MICHELE LUCCIOLA <michelelucciol@...> ha scritto:

Hello and good evening from Rome
This summer I experienced  on  my SM2000 some troubles with the reading of the B&G speedometer.
I saw the documents in the files section, but there is not indication about how to replace them.
 I have to replace the sensors (that I have found in Ebay) but I'm not sure that this is an easy work ....especially to remove the old ones. Does anyone did this job before? I'm very scared about the sensor on the keel....I have seen that the sensors are two little plastic tubes but I don't know how they are fixed to the boat because there is no o'rings on the tube so I assumed that the tube is fixed with resin to the hull and to the keel....
If possible I prefer to replace the sonic speed sensors and don't do a new hole to instal a new sensor; for that reason I will be happy to receive comments from you
Thanks in advance
Michele


Re: Converting my Amel 54 to lithium batteries: what I did, what I like and what I don't like (after one year of full time live aboard use)

Rudolf Waldispuehl
 

Hi Scott

 

Hope you are doing well and everything is ok on board.

 

Next week we start to work on the LFP project and it came to my mind I have read somewhere that the AC cooling pump in the engine room is not sourced from the main 240V board.

It is sourced in the engine room and somebody mentioned that AC pump after changing and rewiring to LFP was not working due to of this because Climma power box is in the engine room.

 

I don’t remember it was you or maybe someone else? To my understanding, if not rewired on a strange way it should still work.

How is this in your case using the AC on LFP or you had to re-wire the 240V for the Pump in the Engine room?

 

Best regards

Ruedi

 

==========================

 

Jamie,

Good to hear it's working out for you. Have you tried to run AC all night on battery yet? We draw 25-35% if we run just aft AC overnight.

For your Mastervolt alternator regulator, I had the same problem and solved it with a solid state relay and two Hella relays. See #50689  

We charge with 200amps nominal (120a Quattro + 80 a Skylla) and only see high temperatures at the very end of charging (95% SOC +) or if one of the cells is severely imbalanced relative to the rest of the cells in the battery. Note that this imbalance shows up as a voltage difference, but due to the flat charge/discharge curve of lithium, you won't notice it until 90%+ SOC. Can you monitor cell level voltage? With the Victron batteries, you can connect via bluetooth and do just that.

Also I'm surprised you can't change charging current via VictronConnect on your PC. I typically connect to my Quattro using ethernet, but I connect to my solar controller via bluetooth (from my Mac) and can change everything via bluetooth.

Keep in mind that you will need to revise how you think about SOC and longevity. Lithiums do NOT like being kept anywhere near full. I try to cycle mine between 40-85% (ideally no more than 80%) SOC and then charge it up to 100% once a month to balance out the cells, since balancing only occurs on the Victrons when they're nearly full. Independent literature indicates I'll get over 5000 cycles doing this. I know some who take it between 10-100% SOC daily and have been fine for a few years, FYI.

Monthly charging to 100% also resets the BMV-712 battery monitor. Not sure which BM you have, but don't forget to change the settings on it to match lithium. Of course, you MUST set all the chargers to lithium profiles otherwise you will kill the batteries very quickly.

So you've been thinking about charging cutoffs - how do you deal with low voltage cutoff? As mentioned in that post, I opted not to use the BatteryProtect, which would disconnect loads when there's a cell low voltage condition, but rather I'm trying to get the Victron charger/inverter to trigger the generator to start when cell low voltage and/or low SOC is encountered. Sounds like you're an engineer - want to help figure that out? :)


--
Scott 
2007 A54 #69
SV Tengah
http://www.svtengah.com


Re: Shore - Generator Switch-over box on A54 #solution

Mohammad Shirloo
 

Hello Ian;

 

My knowledge of the LN175 and Dolphin charger is limited, so I will not be of much help there. I can share with you our current approach for our charging and inversion plans, as we make the necessary upgrades, as equipment fails.

 

Our 2500W Mastervolt inverter failed at the end of the 2019 season. We would like to use the existing charger wiring in the engine room. We have replaced our inverter with a MV Mass Combi Ultra 24/3500. These inverter /chargers can charge at 100A, provide 3500W 220V and have solar controllers built in. They can also be connected in series for additional charging and inversion output. We intend to have 2 in series, giving us 200A charging/7000 W inversion. We will still have our existing 40A MV charger, for a total of 240A charging. I have not checked the existing 40A charging wiring size. It is possible to add a third combi Ultra for  max of 300A charging and 10,500W of inversion. The Combi Ultra can also be programmed to limit the charge/inversion output to match the wiring size. The plan is to be able to supply the entire 220V panel from the inverters.

 

We have not gone far down the design phase, as this is some time away for us. However, I like the small size (same appx footprint as the inverter we replaced) and light weight of  combi/ultra. We should be able to fit 2 and possibly three in the same footprint and location of the existing chargers. Minimal wiring and full integration, monitoring and control of the Lithium batteries, chargers, inverters and solar.

 

All of this is very preliminary. In the next 2-3 years that it will take for us to be ready to make the upgrade, I’m sure may thing have changed  that will require changes to our basic design concept.

 

Respectfully;

 

 

Mohammad and Aty

B&B Kokomo

Amel 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Ian Fraser via groups.io
Sent: Friday, September 17, 2021 2:16 PM
To: main@amelyachtowners.groups.io
Cc: Ian Fraser <keyproperties@...>
Subject: Re: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Mohammad,

 

Thank you for your insights on Lithium. We are in a similar situation and agree that Lithium is too early for us.

 

Will really appreciate your guidance on best solutions for changes to LN175 alternator (and Dolphin 100A Charger) when upgrading to 8AGM 105Ahr on AMEL54 #009.

Regards,

Ian Fraser
Dreamtime.   

On 17 Sep 2021, at 03:27, Mohammad Shirloo <mshirloo@...> wrote:

 

Hi Ruedi;

 

We are currently in the Med and, in my opinion,  Lithium is not a huge advantage in our cruising style here. Also our AGMs that we installed in 2018, have been working better than expected and almost as good as when installed new.

 

I believe that Lithium technology for yachts is in its infancy and the improvement curve fairly steep. Our plan is to convert to Lithium in about 2-3 years, before leaving the Med, so we can benefit from all the advancement in technology and safety. 

 

Respectfully;

 

 

Mohammad and Aty

B&B Kokomo

Amel 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Rudolf Waldispuehl via groups.io
Sent: Thursday, September 16, 2021 11:28 PM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Hi Mohammad and Aty

 

Thank you for the drawing which helped me a lot. Exactly this page was not in my documentation. Don’t know why?

I found in the 220V Panel drawing K1- and K2-source referenced, but without any detail about K1 and K2. Now everything is very clear and you are absolutely right with the priorities.

 

  • When there is Power from the Generator, K1 is interrupting the Shore supply and switching to Generator with the K1 Relay.
  • When there is any Power from any K1 source (GE or Shore), K2 is active and the Inverter is not switched because K2 is keeping the Inverter 220V output unswitched (offline).
    • Even if the inverter is ON, it can’t deliver 220V to the panel, because K2 is ON as long as K1 delivers power.

 

This sound a bit complicated but it’s finally the priority GEN, Sore, Inverter as you said.

 

BTW: What is your Lithium Project doing? You have changed KOKOMO to Lithium meanwhile?

 

Thanks and fair winds

Ruedi & Sabina Waldispuehl

"SY WASABI"

Amel 54. #55

Currently in Estepona heading to Gibraltar

 

 

Von: "main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io> im Auftrag von Mohammad Shirloo <mshirloo@...>
Antworten an: "
main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Datum: Donnerstag, 16. 
September 2021 um 07:40
An: "
main@AmelYachtOwners.groups.io" <main@AmelYachtOwners.groups.io>
Betreff: Re: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Hi Ruedi;

 

There are electrical schematics in the original AMEL operator’s manual in the Appendix section, that came with the yacht, that show how they are wired. Attached is the schematic for the K1-K2 switchover relays.

 

I believe K1 and K2 switch/relays make the selection of power source.  Power first  goes through K1 which selects the source between shore power and generator. I believe that generator has priority over shore power. Once this source is selected, it goes through K2, which selects between the output of K1 and the inverter, with the output of K1 having higher priority.

 

I am fairly certain that the priority is: 

 

  1. Generator
  2. Shore power
  3. Inverter

 

Respectfully;

 

 

Mohammad and Aty

B&B Kokomo

Amel 54 #099

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Rudolf Waldispuehl via groups.io
Sent: Wednesday, September 15, 2021 8:31 PM
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Shore - Generator Switch-over box on A54 #solution

 

Hello Amelian's

 

I tried to find out how the Shore/Generator Switchover Box in the Engine room of my Amel-54 is exactly working. I do have in addition a 2500W MV inverter installed originally from AMEL. Last few weeks the Switch-over is doing strange things and fuses are blowing. 

 

I have not found any accurate information (drawings) electric scheme of that AMEL specific switch-over mechanism. I don’t know how it detects either one or all 3 of the 240V sources, and which is the master over-ruling the Generator or Shore and/or Inverter. How it protects the Inverter when Shore or Generator is running, etc… 
Does anyone out there have any detailed information how these system works and may have an Electric scheme with in dept knowledge how it works?

 

Thanks a lot for investigation and best regards
Ruedi Waldispuehl
WASABI 

WASABI A54. #55

E-MAIL: mail@...

 


Re: LED under cabinet lighting

Michael Winand
 

We went with a 4 colour led, needs to be attached to a aluminum strip, for the heat sink. Has a diffusion cover. 
Went with a wired controller,  it has dimmer,  3 white colour choice,  took the power from the galley exhaust fan. 
Lots of choices these days. 
Michael Nebo sm251 

On Sun, 19 Sep 2021, 12:36 pm Germain Jean-Pierre, <jp.germain45@...> wrote:
Hello Gang,

We added a bright white LED string under the cabinet above the sink and extended it all the way to the port most locker. Lots of light

Jean-Pierre Germain, Eleuthera SM007. NZ’s 


On 19/09/2021, at 1:49 PM, Bill Kinney <cruisingconsulting@...> wrote:

Pat, 

It's always a little dicey doing what you suggest.  Part of the reason is that on a boat "24V" isn't ever really "24V"  It can range up to almost 29V depending on your battery charging scheme.  LEDs that are setup for a constant 24V might have a shortened lifespan driven at high voltages.

I KNOW you can find marine grade LEDs and controllers to do exactly what you want that will be honestly rated for 10 to 30V.  You might pay a bit more, but...

We did basically the same thing, except with plain white LEDs.  What a difference:  Cooking in the galley with BRIGHT lights!

Bill Kinney
SM160, Harmonie
Annapolis, MD, USA


Re: LED under cabinet lighting

Germain Jean-Pierre
 

Hello Gang,

We added a bright white LED string under the cabinet above the sink and extended it all the way to the port most locker. Lots of light

Jean-Pierre Germain, Eleuthera SM007. NZ’s 


On 19/09/2021, at 1:49 PM, Bill Kinney <cruisingconsulting@...> wrote:

Pat, 

It's always a little dicey doing what you suggest.  Part of the reason is that on a boat "24V" isn't ever really "24V"  It can range up to almost 29V depending on your battery charging scheme.  LEDs that are setup for a constant 24V might have a shortened lifespan driven at high voltages.

I KNOW you can find marine grade LEDs and controllers to do exactly what you want that will be honestly rated for 10 to 30V.  You might pay a bit more, but...

We did basically the same thing, except with plain white LEDs.  What a difference:  Cooking in the galley with BRIGHT lights!

Bill Kinney
SM160, Harmonie
Annapolis, MD, USA


Re: LED under cabinet lighting

Bill Kinney
 

Pat, 

It's always a little dicey doing what you suggest.  Part of the reason is that on a boat "24V" isn't ever really "24V"  It can range up to almost 29V depending on your battery charging scheme.  LEDs that are setup for a constant 24V might have a shortened lifespan driven at high voltages.

I KNOW you can find marine grade LEDs and controllers to do exactly what you want that will be honestly rated for 10 to 30V.  You might pay a bit more, but...

We did basically the same thing, except with plain white LEDs.  What a difference:  Cooking in the galley with BRIGHT lights!

Bill Kinney
SM160, Harmonie
Annapolis, MD, USA


Re: Amel 55 Hardtop & Mainsheet question

Arno Luijten
 

Well, call me crazy but Ireally prefer the cabrio version. For me it’s much more elegant…

Cheers,

Arno Luijten
SV Luna,
A54-121


Re: LLC or Corporate ownership of vessel

rossirossix4
 

I am fairly sure it was the same Harbour Master for Porto Montenegro,  at the Tivat customs dock who readily accepted our Florida boater "license".  She squinted to read the numbers, those little zeros on Mark's sample card. Worked later on in Cavtat, Croatia as well and some island I can't remember in Greece.

We also carry a special universal set of special permision items for harbour masters (Albania), military and coast guard boarders (Morocco), berthing requests (Italy, Gozo and 2 month Covid lock-down in Colombia), and workmen who we want to give us fair rates or better service (Turkey and Tunisia).  Seems to be universally accepted and you don't have to worry about pesky translation problems.     https://photos.app.goo.gl/9499u2EgwRqyffAP6

Somewhat related, we always stamp the sales receipts and even boxes for items we are bringing through customs (self inker $10 on eBay) and we include a stamped color 2-sided copy of our USCG Document in each suitcase that have items and boat parts  https://photos.app.goo.gl/MgRpPdEBBjNbySV57 

No guarantee but so far 23 countries, no problems.

Cheers, 
Bob     KAIMI SM429


Re: Amel 55 Hardtop & Mainsheet question

amelforme
 

Hi All. Of I believe 68 Amel 55’s built, 3 had the cabriolet configuration. The demonstration boat provided to me by Amel was roundly disliked by almost everyone who came aboard. The guy who bought it after its service was complete made reconfiguring it into a hard top the primary codicil of his purchase agreement. And then there was two…  

 

All the best,

Joel

 

           JOEL F. POTTER ~ CRUISING YACHT SPECIALIST, L.L.C.

                                         The Experienced AMEL Guy

UNSURPASSED AMEL MARKETING EXPERIENCE AND PRODUCT KNOWLEDGE

                                  Office 954-462-5869  Cell 954-812-2485

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of CW Bill Rouse
Sent: Saturday, September 18, 2021 2:18 PM
To: main@AmelYachtOwners.groups.io Notification <main@amelyachtowners.groups.io>
Subject: Re: [AmelYachtOwners] Amel 55 Hardtop & Mainsheet question

 

Based on what I have seen, very few were sold.



CW Bill Rouse Amel Owners Yacht School

Address: 720 Winnie, Galveston Island, Texas 77550 

 

View My Training Calendar

 

On Sat, Sep 18, 2021 at 10:08 AM Arno Luijten <arno.luijten@...> wrote:

Hi Bill,

Did they sell many of the cabriolet version?

Arno


Re: Amel 55 Hardtop & Mainsheet question

 

Based on what I have seen, very few were sold.


CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar

On Sat, Sep 18, 2021 at 10:08 AM Arno Luijten <arno.luijten@...> wrote:
Hi Bill,

Did they sell many of the cabriolet version?

Arno


Re: Amel 55 Hardtop & Mainsheet question

Arno Luijten
 

Hi Bill,

Did they sell many of the cabriolet version?

Arno


Re: Amel 55 Hardtop & Mainsheet question

 

Arno & Jose,

Yes, I can see all sorts of issues with the hardtop rigging, one of which is there is no hardtop on the Cabriolet and that means significant changes between the two models. Frankly, I would be a little hesitant about the first hardtop rigging and I can see these being pulled from the hardtop structure. But, maybe they changed to simplify the production between the Cabriolet and the hardtop.

Bill


CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar

On Sat, Sep 18, 2021 at 9:52 AM Jose Alegria <Josealegr@...> wrote:
Hi Bill
Maybe Amel concluded the cockpit structure is not strong enough for support the main load forces particularly if the boom move quickly from one side to other. 
Cheers


Jose Alegria
Amel55 #03-MERIT
+351918663037



No dia 18/09/2021, às 16:51, Arno Luijten <arno.luijten@...> escreveu:

Hi Bill,

Interesting observation.
I cant' give you a proper answer but using Yachtworld pictures I do notice this change happened around 2014, which I believe coincide with the mid-lifecycle update Amel did when they also revamped the dashboard with different switches etc.
The new solution does look cleaner although I still feel the lack of a proper traveller is a shame, even though they did bring back the rod-kicker which is dearly missed on our A54.
Given the way they rigged it in the latter solution I do think you should be careful with the main sheet when the boom is out. It may catch something and get snagged if the pressure on the sail is momentary lost because of sea motion
For abandoning initial solution, it does expose quit some forces at a point of the boat that has limited natural structural rigidity. Given how many boats use arches for the main sheet nowadays I suppose that is not a big problem.

Cheers,

Arno Luijten
SV Luna
A54-121


Re: Amel 55 Hardtop & Mainsheet question

Jose Alegria
 

Hi Bill
Maybe Amel concluded the cockpit structure is not strong enough for support the main load forces particularly if the boom move quickly from one side to other. 
Cheers


Jose Alegria
Amel55 #03-MERIT
+351918663037
Josealegr@...



No dia 18/09/2021, às 16:51, Arno Luijten <arno.luijten@...> escreveu:

Hi Bill,

Interesting observation.
I cant' give you a proper answer but using Yachtworld pictures I do notice this change happened around 2014, which I believe coincide with the mid-lifecycle update Amel did when they also revamped the dashboard with different switches etc.
The new solution does look cleaner although I still feel the lack of a proper traveller is a shame, even though they did bring back the rod-kicker which is dearly missed on our A54.
Given the way they rigged it in the latter solution I do think you should be careful with the main sheet when the boom is out. It may catch something and get snagged if the pressure on the sail is momentary lost because of sea motion
For abandoning initial solution, it does expose quit some forces at a point of the boat that has limited natural structural rigidity. Given how many boats use arches for the main sheet nowadays I suppose that is not a big problem.

Cheers,

Arno Luijten
SV Luna
A54-121

881 - 900 of 60972