|
Re: [Amel] Dessalator 160 liter per hour water maker low pressure pump
Judy and Bill aboard SV BeBe <yahoogroups@...>
Photos at http://groups.yahoo.com/group/amelyachtowners/photos/album/1219017177/pic/991865346/view?picmode=&mode=tn&order=ordinal&start=21&count=20&dir=asc
toggle quoted messageShow quoted text
and http://groups.yahoo.com/group/amelyachtowners/photos/album/1219017177/pic/623307687/view?picmode=&mode=tn&order=ordinal&start=21&count=20&dir=asc Hope this helps...let me know if you need anything else Bill s/v BeBe
--- In amelyachtowners@yahoogroups.com, "Judy and Bill aboard SV BeBe" <yahoogroups@...> wrote:
|
|
|
|
Re: [Amel] Dessalator 160 liter per hour water maker low pressure pump
Judy and Bill aboard SV BeBe <yahoogroups@...>
Anne and John Hollamby,
toggle quoted messageShow quoted text
I have photos of both pumps which I will post in "Dessalator Water Maker Service" in the photo section of this website in about an hour. I will attempt to get you sizes of the fittings attached. I did find out that the specs of the pump are: 230v 300w 900liters/hour and 3.5 bar of pressure and that a new pump from Dessalator is 802 Euros...that may make you feel better about your repair. Best, Bill s/v BeBe, SM2k, #387 Currently Singapore Blog: http://www.svbebe.com
--- In amelyachtowners@yahoogroups.com, " Anne and John Hollamby" <annejohnholl@...> wrote:
|
|
|
|
Re: [Amel] Autohelm 7000 low battery
kimberlite <kimberlite@...>
I would also check the voltage at the connection for the control head at the
course computer. It should be 12 volts. Only the drive motor works on 24 volts, the clutch is also 12 volts. Fair Winds Eric Amel Super Maramu #376 Kimberlite _____ From: amelyachtowners@yahoogroups.com [mailto:amelyachtowners@yahoogroups.com] On Behalf Of Diane Nielsen Sent: Wednesday, June 02, 2010 12:30 PM To: amelyachtowners@yahoogroups.com Subject: Re: [Amel] Autohelm 7000 low battery Thank you for all of the suggestions. We Judy and Bill aboard SV BeBe <yahoogroups@svbebe.com <mailto:yahoogroups%40svbebe.com> > wrote: Assuming that you have good voltage at that point, I can almost guaranty that the following will work. Using a small brush, coat all of the wire contact points where a wire, connector, or a clip joins either the course computer, the drive, and the control head. If a Raymarine Seatalk connector is used at the control head, remove it and coat the pins and the inside of the receptacle. everything. It is a private company that produces CorrosionX for Aviation and Marine solutions. http://www.corrosionx.com/ It is not flammable. If you have to ship it via air, buy the trigger bottle, because the aerosol will be considered dangerous. company, I would buy stock! like you described.
|
|
|
|
Re: [Amel] Anti foul
Conn Williamson <connwilliamson@...>
Yes Richard I googled up Trinadad and found the price in the US was Xy as well. I also found a site here from the government pesticides & vetinary authority recalling all Trinadad antifoul, it diddn't say why, but I have a fair idea. We pay around 200-250 per 4liters for anti foul paint. Altex 5 is a New Zealand product.
________________________________ From: Richard Piller <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Wed, June 2, 2010 11:03:38 PM Subject: Re: [Amel] Anti foul Conn, you are not alone on the price issues, we have seen bottom paint from US$400 down to 225 for the same can of paint.. Be advised and look around..... We don't see Altex X here in the US or Caribb. Enjoy the boat... Richard on SM 209 ________________________________ From: Conn Williamson <connwilliamson@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Tue, June 1, 2010 10:25:41 PM Subject: Re: [Amel] Anti foul Thanks again Richard. Our old boat was a 30 footer so I diddn't know how much to order for the larger size. 5 gallons here costs over 1000 bucks so I diddn't want to over order. I don't know if I can get Trinadad in OZ. Iwas going to use Altex V. ________________________________ From: "richard03801@yahoo.com" <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Wed, June 2, 2010 8:45:26 AM Subject: Re: [Amel] Anti foul We us two coats after sanding with rough grit paper. Given you have a Mango be shore to check for blisters. If you have them take care before you paint. Paint does not hold well to blistered areas. By the way we generally get 2 years out of Trinadad SR. Good luck. Richard SM209 Sent via BlackBerry by AT&T -----Original Message----- From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 14:19:58 To: <amelyachtowners@yahoogroups.com> Subject: Re: [Amel] Anti foul Thanks Richard, do you apply 1 or 2 coates. ________________________________ From: "richard03801@yahoo.com" <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Tue, June 1, 2010 9:59:52 PM Subject: Re: [Amel] Anti foul We generally use 5 gal Pettit Trinadad SR on our SM. Richard SM209 Sent via BlackBerry by AT&T -----Original Message----- From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 02:00:29 To: <amelyachtowners@yahoogroups.com> Subject: [Amel] Anti foul We haven't had our Mango for long and I am slipping it soon. Just wondering about how much antifoul paint I might need. [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
|
|
|
|
Amel Marmu Questions
Philip
Hello,
My wife and I have an accepted offer for a 1985 46' Maramu Nirvana Ketch. It has mostly original equipment and rigging, including the electric furling on the head sail and main. This weekend we will be doing the sea trial and then the survey next week. We would greatly appreciate any advice about things to look for during the sea trial and survey. Are there things you, as owners, wished you had checked in advance? Are there maintenance or refit issues we should be prepared for? As long time and fairly long distance cruisers we are quite taken with the Amel, even if this one does not work out we will certainly look for another. Thanks in advance for any and all suggestions. -Phil Anacortes, WA
|
|
|
|
Clima Air condtioner
george cerillo
Has anyone replaced the Clima A/C unit with a different unit? We are contemplating Cruise Air.
George Cerillo #353 Indecent
|
|
|
|
replacing the Clima Air conditioning unit
george cerillo
Hello,
We are contemplating replacing our Clima AC units for Cruise Air, due to the fact that we have 2 compressors that are shot. Does anyone have any experience replacing the Clima units with a different AC? Any responses would be helpful. George hull #353 Indecent
|
|
|
|
Re: [Amel] Autohelm 7000 low battery
Diane Nielsen <dianexnielsen@...>
Thank you all for the suggestions. We will be purchasing the corrosionx and hope that will fix the problem. Certainly don't want to replace the autohelm! I will let you know how it goes. Thanks again. Pat and Diane sm123 Shenanigans Sassafras River, MD
toggle quoted messageShow quoted text
Judy and Bill aboard SV BeBe <yahoogroups@svbebe.com> wrote:
|
|
|
|
Re: [Amel] Autohelm 7000 low battery
Diane Nielsen <dianexnielsen@...>
Thank you for all of the suggestions. We
toggle quoted messageShow quoted text
Judy and Bill aboard SV BeBe <yahoogroups@svbebe.com> wrote:
|
|
|
|
Re: [Amel] Dessalator 160 liter per hour water maker low pressure pump
Anne and John Hollamby <annejohnholl@...>
Hi Bill,
toggle quoted messageShow quoted text
I had my LP Pump serviced by Dessalateur at huge cost. It has come back without some of the fittings to the four ins and outs and I am not sure which one does which. Please tell me Best wishes from Malta, John, SM219 Bali Hai
----- Original Message -----
From: Richard Piller To: amelyachtowners@yahoogroups.com Sent: Wednesday, June 02, 2010 3:15 PM Subject: Re: [Amel] Dessalator 160 liter per hour water maker low pressure pump Hi Bill, we use a Surflo controlled pressure pump before the high pressure pump it has a rate of 3.2 gal per min or 192 per hour at 30 psi.. with an auto shut off if pressure goes to high. That should do the deed for you. It was an easy install out of the salt water manifold into a 30 micron filter and to the pre-high pressure pump to the high pressure pump. No starvation to the high pressure pump just clean water? salt water. We also use a 10 micron charcoal filter before from the fresh water tank before the fresh water pressure system to be very sure we get NO chlorine into the membrane. Good luck.. Richard and Joan on SM 209 ________________________________ From: Judy and Bill aboard SVBeBe <yahoogroups@svbebe.com> To: amelyachtowners@yahoogroups.com Sent: Wed, June 2, 2010 1:12:35 AM Subject: [Amel] Dessalator 160 liter per hour water maker low pressure pump Does anyone have the specs on the 230v low pressure pump on the 160lph water maker. I am looking for gallons/hour or some such water flow spec to be able to buy a spare/replacement pump. I emailed Dessalator, but no response. I guess they knew that I was probably looking to buy the pump elsewhere. Best, Bill s/v BeBe, SM2k, #387 Currently Malaysia Blog http://www.svbebe.com [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
|
|
|
|
Re: [Amel] Dessalator 160 liter per hour water maker low pressure pump
Richard Piller <richard03801@...>
Hey, I just realized that you were asking for a 220 volt pump what I had suggested was a 24 volt pump.. I don't have one with me now but if you look on the "Budget Marine" St. Martin web site they have a number of 220 volt pumps that will do the job. We use one for the AC flow it also has a cooling loop for the pump itself.. Sorry I don't have access to the catalog for more detail
Richard SM 209 ________________________________ From: Judy and Bill aboard SV BeBe <yahoogroups@svbebe.com> To: amelyachtowners@yahoogroups.com Sent: Wed, June 2, 2010 1:12:35 AM Subject: [Amel] Dessalator 160 liter per hour water maker low pressure pump Does anyone have the specs on the 230v low pressure pump on the 160lph water maker. I am looking for gallons/hour or some such water flow spec to be able to buy a spare/replacement pump. I emailed Dessalator, but no response. I guess they knew that I was probably looking to buy the pump elsewhere. Best, Bill s/v BeBe, SM2k, #387 Currently Malaysia Blog http://www.svbebe.com [Non-text portions of this message have been removed]
|
|
|
|
Re: [Amel] Dessalator 160 liter per hour water maker low pressure pump
Richard Piller <richard03801@...>
Hi Bill, we use a Surflo controlled pressure pump before the high pressure pump it has a rate of 3.2 gal per min or 192 per hour at 30 psi.. with an auto shut off if pressure goes to high. That should do the deed for you. It was an easy install out of the salt water manifold into a 30 micron filter and to the pre-high pressure pump to the high pressure pump. No starvation to the high pressure pump just clean water? salt water. We also use a 10 micron charcoal filter before from the fresh water tank before the fresh water pressure system to be very sure we get NO chlorine into the membrane.
Good luck.. Richard and Joan on SM 209 ________________________________ From: Judy and Bill aboard SVBeBe <yahoogroups@svbebe.com> To: amelyachtowners@yahoogroups.com Sent: Wed, June 2, 2010 1:12:35 AM Subject: [Amel] Dessalator 160 liter per hour water maker low pressure pump Does anyone have the specs on the 230v low pressure pump on the 160lph water maker. I am looking for gallons/hour or some such water flow spec to be able to buy a spare/replacement pump. I emailed Dessalator, but no response. I guess they knew that I was probably looking to buy the pump elsewhere. Best, Bill s/v BeBe, SM2k, #387 Currently Malaysia Blog http://www.svbebe.com
|
|
|
|
Re: [Amel] Anti foul
Richard Piller <richard03801@...>
Conn, you are not alone on the price issues, we have seen bottom paint from US$400 down to 225 for the same can of paint.. Be advised and look around..... We don't see Altex X here in the US or Caribb.
Enjoy the boat... Richard on SM 209 ________________________________ From: Conn Williamson <connwilliamson@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Tue, June 1, 2010 10:25:41 PM Subject: Re: [Amel] Anti foul Thanks again Richard. Our old boat was a 30 footer so I diddn't know how much to order for the larger size. 5 gallons here costs over 1000 bucks so I diddn't want to over order. I don't know if I can get Trinadad in OZ. Iwas going to use Altex V. ________________________________ From: "richard03801@yahoo.com" <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Wed, June 2, 2010 8:45:26 AM Subject: Re: [Amel] Anti foul We us two coats after sanding with rough grit paper. Given you have a Mango be shore to check for blisters. If you have them take care before you paint. Paint does not hold well to blistered areas. By the way we generally get 2 years out of Trinadad SR. Good luck. Richard SM209 Sent via BlackBerry by AT&T -----Original Message----- From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 14:19:58 To: <amelyachtowners@yahoogroups.com> Subject: Re: [Amel] Anti foul Thanks Richard, do you apply 1 or 2 coates. ________________________________ From: "richard03801@yahoo.com" <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Tue, June 1, 2010 9:59:52 PM Subject: Re: [Amel] Anti foul We generally use 5 gal Pettit Trinadad SR on our SM. Richard SM209 Sent via BlackBerry by AT&T -----Original Message----- From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 02:00:29 To: <amelyachtowners@yahoogroups.com> Subject: [Amel] Anti foul We haven't had our Mango for long and I am slipping it soon. Just wondering about how much antifoul paint I might need. [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
|
|
|
|
Re: [Amel] Dessalator 160 liter per hour water maker low pressure pump
David Mackintosh <dlm48@...>
well if they did not - they do NOW!!!!
BTW FYI When we last anchored in CC in April MOORSECURE had just laid 6 moorings in the east side of the anchorage - that was one days work and we left the anchorage to go home at 6am the next day so CC could be full of moorings now :-( kindest regards David On 2 June 2010 06:12, Judy and Bill aboard SV BeBe <yahoogroups@svbebe.com>wrote:
[Non-text portions of this message have been removed]
|
|
|
|
Dessalator 160 liter per hour water maker low pressure pump
Judy and Bill aboard SV BeBe <yahoogroups@...>
Does anyone have the specs on the 230v low pressure pump on the 160lph water maker. I am looking for gallons/hour or some such water flow spec to be able to buy a spare/replacement pump. I emailed Dessalator, but no response. I guess they knew that I was probably looking to buy the pump elsewhere.
Best, Bill s/v BeBe, SM2k, #387 Currently Malaysia Blog http://www.svbebe.com
|
|
|
|
Re: [Amel] Anti foul
Conn Williamson <connwilliamson@...>
Thanks again Richard. Our old boat was a 30 footer so I diddn't know how much to order for the larger size. 5 gallons here costs over 1000 bucks so I diddn't want to over order. I don't know if I can get Trinadad in OZ. Iwas going to use Altex V.
________________________________ From: "richard03801@yahoo.com" <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Wed, June 2, 2010 8:45:26 AM Subject: Re: [Amel] Anti foul We us two coats after sanding with rough grit paper. Given you have a Mango be shore to check for blisters. If you have them take care before you paint. Paint does not hold well to blistered areas. By the way we generally get 2 years out of Trinadad SR. Good luck. Richard SM209 Sent via BlackBerry by AT&T -----Original Message----- From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 14:19:58 To: <amelyachtowners@yahoogroups.com> Subject: Re: [Amel] Anti foul Thanks Richard, do you apply 1 or 2 coates. ________________________________ From: "richard03801@yahoo.com" <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Tue, June 1, 2010 9:59:52 PM Subject: Re: [Amel] Anti foul We generally use 5 gal Pettit Trinadad SR on our SM. Richard SM209 Sent via BlackBerry by AT&T -----Original Message----- From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 02:00:29 To: <amelyachtowners@yahoogroups.com> Subject: [Amel] Anti foul We haven't had our Mango for long and I am slipping it soon. Just wondering about how much antifoul paint I might need. [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
|
|
|
|
Re: [Amel] Anti foul
richard03801@...
We us two coats after sanding with rough grit paper. Given you have a Mango be shore to check for blisters. If you have them take care before you paint. Paint does not hold well to blistered areas.
toggle quoted messageShow quoted text
By the way we generally get 2 years out of Trinadad SR. Good luck. Richard SM209 Sent via BlackBerry by AT&T
-----Original Message-----
From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 14:19:58 To: <amelyachtowners@yahoogroups.com> Subject: Re: [Amel] Anti foul Thanks Richard, do you apply 1 or 2 coates. ________________________________ From: "richard03801@yahoo.com" <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Tue, June 1, 2010 9:59:52 PM Subject: Re: [Amel] Anti foul We generally use 5 gal Pettit Trinadad SR on our SM. Richard SM209 Sent via BlackBerry by AT&T -----Original Message----- From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 02:00:29 To: <amelyachtowners@yahoogroups.com> Subject: [Amel] Anti foul We haven't had our Mango for long and I am slipping it soon. Just wondering about how much antifoul paint I might need.
|
|
|
|
Re: [Amel] Anti foul
Conn Williamson <connwilliamson@...>
Thanks Richard, do you apply 1 or 2 coates.
________________________________ From: "richard03801@yahoo.com" <richard03801@yahoo.com> To: amelyachtowners@yahoogroups.com Sent: Tue, June 1, 2010 9:59:52 PM Subject: Re: [Amel] Anti foul We generally use 5 gal Pettit Trinadad SR on our SM. Richard SM209 Sent via BlackBerry by AT&T -----Original Message----- From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 02:00:29 To: <amelyachtowners@yahoogroups.com> Subject: [Amel] Anti foul We haven't had our Mango for long and I am slipping it soon. Just wondering about how much antifoul paint I might need. [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
|
|
|
|
Re: [Amel] Anti foul
richard03801@...
We generally use 5 gal Pettit Trinadad SR on our SM.
toggle quoted messageShow quoted text
Richard SM209 Sent via BlackBerry by AT&T
-----Original Message-----
From: Conn Williamson <connwilliamson@yahoo.com> Date: Tue, 1 Jun 2010 02:00:29 To: <amelyachtowners@yahoogroups.com> Subject: [Amel] Anti foul We haven't had our Mango for long and I am slipping it soon. Just wondering about how much antifoul paint I might need.
|
|
|
|
Anti foul
Conn Williamson <connwilliamson@...>
We haven't had our Mango for long and I am slipping it soon. Just wondering about how much antifoul paint I might need.
|
|
|