Hi all Super Malamud no 39 problem that bow thruster hasower but can't get it to go down just hearing humming sound from motor Any advice elf be good Thanks Barb

on my 1980 Sharki there is the original wire halyard for the main sail. All my advice has been to replace it with rope halyard. However being an Amel and reading the forum's advice not to alter the

Charles, Where is your boat? Fair Winds Eric Kimberlite Amel Super Maramu #376

Hi Andy At the moment I am very busy leaving Sunny Side on a yard still end of the year. There are a lot of detail on the subject, and my English is quite poor, so I need a lot of time to give you a

Hi Gabriele, Thanks for your posts on the diesel tank leak. I would appreciate if you could forward me more information on how you removed the tank and repaired the leaking welded seam (s) Thank you

Glad I could Help Paul, Out of curiosity who is the maker of the water proof boxes? Sincerely, Alexandre --------------------------------------------

Erci, Thanks again. I plan to be in Saint Martin on 6 May, departing 10 May or so for the crossing. Charles On 23/04/2015 08:47, "sailormon kimberlite@... [amelyachtowners]" <amelyachtowners@...>

Thank you Alexandre, It was under the floorboard i had planed to use the different boxes, then I found the low cost heavy duty water proof boxes that I thought would fit well into the cockpit looker,

Hi all, the aluminium disc which connects the genoa with the gearbox was broken on my 1991 SM. Asking AMEL about a spare part I have learned that for the older models this disc is no longer

Charles, Kimberlite is in St Maarten Simpson Bay Marina. When do you plan on being on Board? I will be down in a few weeks. I could give you a hand with the faring- Naomi is in the office at

Good advice. Thanks and Eric too. will take action as soon as I am back in St Martin, Charles On 23 Apr, 2015, at 8:11 AM, Beaute Olivier atlanticyachtsurvey@... [amelyachtowners]

Good morning, first of all, these GRP hull shaped fairings are all different (as all AMEL models have different hulls). This means a new mould for a Maramu cannot be made out of a Santorin hull. You

Thanks Alan, I sure will be glad to have pictures when it comes to fixing this problem. Not sure yet how and when I am going to do it. Too bad about Amel not answering. If you get through Christian

Charles, I had the same problem with the fairing on my bow thruster. It was gone when we hauled out in December. After getting no response from Amel, the norm in my experience, I made my own form

I actually had the Faring installed at Bobbys Phillipsburg St Maarten marina years ago. I believe they could haul you and make a new faring in a day or two. I would not make a crossing without

I had to replace my bow thruster because of a lightning strike years ago. The complete thruster came in with the faring separate and had to be cut to fit and then attached to the thruster body. It

I happen to have my 1990 sn24 santorin 46 out of the water for bottom paint. I wouldn't be surprised that the bow thruster & fairing is the same. Does anyone know? Secondly, how would a mould be

Hi Jean Luc Pls give me a hand. How you can messure the current on the shunt near the batteries. Did you Cut of the wired to the shunt and put an Amp-Meter in serial between ? Or you used an clamp-on

Good morning Paul, Sorry for the delay, was raining yesterday so not practical to empty the storage. For the Aft section of the closet: The length is: 40.5 inches or 103 Cm (up to the wood plank

I was able to talk to Christian Dufourd on the phone. He said that the mold for the Maramu’s bow thruster faring had been discarded. So it goes. To be fair, Christian said it was a shame to throw