Hello everyone I have a 2000 SM# 283 with Thomson washer/drier I have notied a slight leak in my clothes washer drier. I believe its from the freshwater intake but I cant be sure. Has anyone had a

Thank you for that, this is of great help Horst - Maramu 168 ________________________________ From: amelyachtowners@... [mailto:amelyachtowners@...] On Behalf Of

Battery box on Maramu hull 192 is: Length from inside forward end to pipe block aft: 43.25" Width: 13.5" This is compressing the foam that is still in my battery box on the engine room wall side. I

I have removed the main to paint and re rig on 1985 Maramu hull # 192. All is apart except I am having difficulty getting the forestay out of the furling tube. I have tied the base to a tree and have

I need new batteries, but am away from the boat. Can anyone please measure the battery box, length and width, - I don't want to end up with having to make a new box! Thank you Horst -

I have available some Navionics charts, never used because I have change my Furuno by a Simrad, the charts cover the Mediterranean coasts from Turquey , Greece, Italy, Balearics, Spanish

For all you loony racers out there in cyberland, you will find a Southern California PHRF handicap rating from 2004 posted in the file section of this forum. There is one error that I did not correct,

hi, i have some photos i would like to post to my photo album on this site but i get the above message when i try to post. what am i doing wrong. thanks eric sm 376 Kimberlite

Our SM 140 "Sula" has a Clyde Yacht Club Association handicap of 17.5. From what I have seen this seems about right. We get no where until it blows 15 kts and will win on a reach in 30kts! As the

Hi Jan & Judy, and Eric, I wish to thank all of you,and all the active and less active members of this group, for always very precious supports . Fair winds...buon vento from MED Venezia. Gianni

I found this on cruising forum website. Fair Winds, Eric Amel Super Maramu #376 Kimberlite Despite doubts over the case, Spade have agreed to modify future bolts, as recommended by the

SM#317, LADY DIVINA IS LOOKING FOR NAVIONIC CHARTS CHIPS THAT WILL FIT A FURUNO NAV NET SYSTEMS (classic) All CHIPS CONSIDERED, BUT LOOKING SPECIFICALLY FOR panama > trinidad # SA-020XL) THANKS

On our '80 Maramu we gave up on the small camp gas bottles and installed aluminum propane bottles in the locker on the back deck. The locker was already vented. A long propane hose was run

Hello all, I entered prop shaft bearing in the search box and read many previous references without finding the one I wanted. The detailed description just posted is excellent but a long time ago

I received this from ian & Judy Jenkins. Fair Winds, Eric Amel Super Maramu #376 Kimberlite HOW TO STRIP DOWN PROPELLER AND STERN GLAND You will need a 24mm spanner or ratchet in addition to usual

Hi Bob Good to hear from you. The prop shaft should be changed every 800 hours. When you bought the boat from me the prop shaft had been changed less that 50 hours before. You should have detailed

Can anyone give a detailed description as how the prop bearings are pulled and replaced. My boatyard mechanic is reluctant to do this as he has not worked on Amels Drive before. Vito, I believe you

I switched to propane tanks. This is easily accomplished with standard small propane tanks, but the valve guard must be sortened to fit into the small locker so a welder must be consulted. The propane

hello. on our maramu we have a (quite) small gaslocker just outside the galley. it has room for two campingaz (blue, 3kg) bottles. has anyone experiance on avarage consumption (how long will a

Hello Lars, I am the AMEL associate for the Americas for nearly 25 years and I have sailed on and sold several Santorins, ketch mainly, a couple of sloops. The main mast is stepped to the same spot,