Can someone confirm the original specification for SM hard dodger glass. What is thickness ? And is it acrylic or polycarbonate ? Ben Driver La Bella Vita SM 347

Paul, Did the supplier assure you that the alternator is an isolated ground alternator? What is the country of origin? If China, forget about it...in my opinion. The pulley size is critical because

Hi, I am about to buy a non-genuine 12v alternator for Volvo D3-110i-C (Amel 54). The supplier has advised me this: Thealternator is 50Amp and is identical in every other way, you will however haveto

Good morning Bill, I now understand what you mean by the 10 mm thickness!!! Around the R8.0 !!! I no longer have the previous gas strut (which I don’t know if the were original), but on them was

Bill Maffei, There could be several reasons for the propeller rubbing against the tube when bursting to Port, but remember the tolerance is very close, and bursts will cause a lateral force one way or

Yes, 2 outside, 1 inside. Bill BeBe 387 On Tue, Jun 21, 2016 at 1:48 PM, Alexandre Uster von Baar uster@... [amelyachtowners] <amelyachtowners@...> wrote:

Ian, I am sure that you know that when everything is perfect, the bow thruster sounds differently between Port and Starboard. This is the way that the reversible pitched 3-blade propeller sounds and

I don't own a Santorin, I own a Super Maramu, I assume they are similar. Consequently I strongly suggest 2 on the foot as Amel originally designed it. And 1 inside. if you have not seen it yet, here

Thanks again friends!! I ordered new foam seals. But now, given what read here,I have to put two or three foam seals on bow thruster shaft of my Santorin?

Hi Bill , we also have different noises on our bow thruster . Amel Guadeloupe had done some work on it and then they were concerned about the different noises in case they had reassembled something

Alex, If you look at the drawing you posted you omitted the end piece specifications which is R8.0 thickness 10 for each end, diameter of the hole in the end which is 8.2mm, and length of the end

Hi Andrew , thanks for that info Ian On 21 Jun 2016, at 11:55, Andrew Lamb andrew.lamb@... [amelyachtowners] <amelyachtowners@...> wrote:

Good morning Bill, I am not technical at all, but isn’t it the “8 mm hinge on each side” the specification of the ends? I just posted the drawing Bansbach sent me on

Thanks Bill, Very helpful. Kind regards Colin Streeter, Island Peal II, SM#332 On Sat, Jun 18, 2016 at 11:06 PM, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] <amelyachtowners@...> wrote: --

Hi We put 3 VictronSPP031401200 solar panels on the Emek solar Arc – they have a similar output. Emek could provide these but we got them from a local tradesman who specializes in domestic solar

Hello Ann-Sofie You said 1500 Ah from the windgenerator during 4 month that I gott to 12,5 Ah aday I might got it wrong? Paul on SYKerpa SM 259

Ian the name is Tera Solar TRP 150B 148x68 cm We have 3 of those so fare very happy with them The remaining info you find on the Web Paul SYKERPA SM 259

Whatever it is 12Ah per day is not even worth considering. We have 600W of solar panels and I checked the meter just now, we got 2.21KwH today, which at 24V = 92Ah We have one freezer and one frig

Sorry I don't understand Paul. What gives 12 Ah/day? If you referr to to my previous e-mail about wind gen, my figures was only for the wind gen. With our intotal 600 W slolarpanel and windgen, we

Hi Paul, Can you tell me how many panels you have on your Emek arch and the dimensions of the panels ? If you know the name of the manufacturer and the name of the panel I can get