|
Display VDS 215 MDS - nav table A54
Dear Amelians,
did any of you have to replace the display on the navigation table?
The manufacturer doesn't seem to produce this anymore.
Are there alternative displays or other sources of supply
Dear Amelians,
did any of you have to replace the display on the navigation table?
The manufacturer doesn't seem to produce this anymore.
Are there alternative displays or other sources of supply
|
By
Stefan Schaufert
·
#58112
·
|
|
Re: Amel 54, For those who do not really like the entrance hatch locking system
Hi Thomas,
I did consider the intermediate position case. Apart from the fact I’m still able to add it if required the reality is that I never used it in the time we’ve owned the boat. When rain
Hi Thomas,
I did consider the intermediate position case. Apart from the fact I’m still able to add it if required the reality is that I never used it in the time we’ve owned the boat. When rain
|
By
Arno Luijten
·
#58111
·
|
|
Re: Holding tank riser
Darren an Karen,
We cut the sump (funnel part) of the tank outlet off. Then we extracted the hose, inserted and glassed in the FRP riser, through the inlet hole and glassed back in the the funnel part
Darren an Karen,
We cut the sump (funnel part) of the tank outlet off. Then we extracted the hose, inserted and glassed in the FRP riser, through the inlet hole and glassed back in the the funnel part
|
By
Peter de Groot
·
#58110
·
|
|
Re: Holding tank riser
Tom and Kristin,
Our solution was to fiberglass in a 1-1/2”OD x 1-1/4” ID FRP tube riser through the inlet hole. The tube went almost to the top of the tank inside. Works well.
Peter de Groot
Tom and Kristin,
Our solution was to fiberglass in a 1-1/2”OD x 1-1/4” ID FRP tube riser through the inlet hole. The tube went almost to the top of the tank inside. Works well.
Peter de Groot
|
By
Peter de Groot
·
#58109
·
|
|
Re: Holding tank riser
Darren and Karen
I made s video on how I sorted out problems with and also filmed inside the holding tank
https://youtu.be/b62ZtpxCPnE
Paul SY Kerpa SM#259
Darren and Karen
I made s video on how I sorted out problems with and also filmed inside the holding tank
https://youtu.be/b62ZtpxCPnE
Paul SY Kerpa SM#259
|
By
Paul Osterberg
·
#58108
·
|
|
Re: House Bank vs. Engine Start
Mark
I have a switch in the cabinet where the steering rack is located
I don’t know if it was original. I left the switch in place, but disconnected the relay that did the remote connection. I
Mark
I have a switch in the cabinet where the steering rack is located
I don’t know if it was original. I left the switch in place, but disconnected the relay that did the remote connection. I
|
By
Ian Park
·
#58107
·
|
|
Re: House Bank vs. Engine Start
Mark,
Can you reproduce the fault by attempting to start the engine while the house bank is turned off?
As Thomas mentioned, maybe you have a PO mod where something in the start/run circuits for the
Mark,
Can you reproduce the fault by attempting to start the engine while the house bank is turned off?
As Thomas mentioned, maybe you have a PO mod where something in the start/run circuits for the
|
By
Dean Gillies
·
#58106
·
|
|
Re: Amel 54 Secondary Saltwater Manifold made by SOFOMARIN of welded polypropylene pipe
Hello Bill, hello Arno,
we are just leaving La Rochelle, I will respond tonight.
Nicolas took measures and pics of the first manifold too. He should be able to create a design of this too.
Martin
Mago
Hello Bill, hello Arno,
we are just leaving La Rochelle, I will respond tonight.
Nicolas took measures and pics of the first manifold too. He should be able to create a design of this too.
Martin
Mago
|
By
Martin Birkhoff
·
#58105
·
|
|
Re: Holding tank riser
Hi Tom and others on this forum,
Kaz and I are newby owners of our Super Maramu #171 and this is our first post to this amazing forum
I found a similar issue with our holding tanks this morning, it
Hi Tom and others on this forum,
Kaz and I are newby owners of our Super Maramu #171 and this is our first post to this amazing forum
I found a similar issue with our holding tanks this morning, it
|
By
Darren Moore
·
#58104
·
|
|
Re: Introduction and a question
Thank you Mark !
By
Roy Zakheym
·
#58103
·
|
|
Re: Amel 54, For those who do not really like the entrance hatch locking system
I would venture to think the idea was to be able to have intermediate positions. Not that we have made use of it much, but maybe one day...
One handed operation sounds great, though
I would venture to think the idea was to be able to have intermediate positions. Not that we have made use of it much, but maybe one day...
One handed operation sounds great, though
|
By
Sv Garulfo
·
#58102
·
|
|
Re: House Bank vs. Engine Start
The house bank and start battery should be completely separate. But you've had not 1 but 2 coincidences. On your boat, the state of the house bank seems to influence the start circuit. Before I did
The house bank and start battery should be completely separate. But you've had not 1 but 2 coincidences. On your boat, the state of the house bank seems to influence the start circuit. Before I did
|
By
Thomas Kleman
·
#58101
·
|
|
Re: House Bank vs. Engine Start
The start battery was a bit over 12 Volt, I didn’t check it at the starter. Once I replaced the house bank everything worked fine, which I fine odd.
The start battery was a bit over 12 Volt, I didn’t check it at the starter. Once I replaced the house bank everything worked fine, which I fine odd.
|
By
Mark Garver
·
#58100
·
|
|
Re: House Bank vs. Engine Start
When you checked the voltage at the battery and starter, what was the reading ?
Tom and Kirstin
SM2K 422
SV L'ORIENT
Tahiti
When you checked the voltage at the battery and starter, what was the reading ?
Tom and Kirstin
SM2K 422
SV L'ORIENT
Tahiti
|
By
Thomas Kleman
·
#58099
·
|
|
House Bank vs. Engine Start
Okay, so recently I had a main bank failure, but what is disturbing is that the engine wouldn’t start. Confusing as I have a dedicated engine start battery, same for the generator. Has anyone
Okay, so recently I had a main bank failure, but what is disturbing is that the engine wouldn’t start. Confusing as I have a dedicated engine start battery, same for the generator. Has anyone
|
By
Mark Garver
·
#58098
·
|
|
Re: Amel 54, For those who do not really like the entrance hatch locking system
Hi Arno,
I know what you mean! Anyone who needs to enter my boat without me present is always amused by the plethora of instructions I give them about entering. Contractors look at you askance ..
Hi Arno,
I know what you mean! Anyone who needs to enter my boat without me present is always amused by the plethora of instructions I give them about entering. Contractors look at you askance ..
|
By
Dean Gillies
·
#58097
·
|
|
Re: solar panel
Hi folks,
Interesting that people comment about getting more output than their panel ratings.
All solar panels have the capability to produce more than their rated output. This is not some some magic
Hi folks,
Interesting that people comment about getting more output than their panel ratings.
All solar panels have the capability to produce more than their rated output. This is not some some magic
|
By
Dean Gillies
·
#58096
·
|
|
Re: Introduction and a question
Roy,
Congratulations!
It's about 59.5cm from the top of the toerail to the top of the lifeline.
--
Mark McGovern
SM #440 Cara
Deale, MD USA
Roy,
Congratulations!
It's about 59.5cm from the top of the toerail to the top of the lifeline.
--
Mark McGovern
SM #440 Cara
Deale, MD USA
|
By
Mark McGovern
·
#58095
·
|
|
Holding tank riser
My aft head holding tank riser has separated from the lower part of the copper fitting. So inflow to the holding tank enters at the bottom of the tank. Despite this, there is no leaking from the
My aft head holding tank riser has separated from the lower part of the copper fitting. So inflow to the holding tank enters at the bottom of the tank. Despite this, there is no leaking from the
|
By
Thomas Kleman
·
#58094
·
|
|
Re: Cook top dimensions
Dave,
The photos of the blocks are on my phone so I'm answering for Denise. We used some leftover 22mm (7/8") thick teak boards from making new passerelle steps to make the support blocks. The
Dave,
The photos of the blocks are on my phone so I'm answering for Denise. We used some leftover 22mm (7/8") thick teak boards from making new passerelle steps to make the support blocks. The
|
By
Mark McGovern
·
#58093
·
|