It would appear that removing to service the motor/gearbox assembly for the winch may be challenging. I am reticent to disturb the bedding and other sealant damages that could occur with removal when

Ken, That is not what I said to you in the email I sent you. I said, For all that want a copy of what I did with Jose and Steve, here is the copy I sent to Ken. Silicone Bow Thruster Seals Designed

My opinion: The engine exhaust hose should be Shieldsflex II 3” wet exhaust hose. http://www.seastarsolutions.com/products/hose/engine-hose/series250/

I am finished with this topic. Bill has some instructions that he may, or may not, share with the rest of the group. After Bill and I exchanged a few emails, I have decided that it's not my place to

Thanks Nicolas; We have pulled and serviced ours a couple of years ago, and did not have any issues. Hoping for the same this time, as we will be doing this in water. Respectfully; Mohammad

Thanks Gary. I watched all 7 a few hours ago, as a refresher. Respectfully; Mohammad Shirloo +1-323-633-2222 Cell +1-424-644-0908 Fax

Good day all, I have searched the forum but have not found what I am looking for. I want to replace the Yanmar exhaust hose but there are so many options with regard to manufacturers and materials

There is a series of YouTube videos on servicing the H6. They are a bit dated, but they were put out by Brunton. Here's the episode about the bearings. . https://youtu.be/zzMcjJFT8E0 . Cheers! Gary

Hello Mohammad I have just serviced my brunton H6 on the hard ,after it had given 16 years of good service ,I don’t know if the previous owner did it,I have no records. I just want to make you

Hi May i put some questions to you who have already installed an inductive cooker? Re electric installation, did you get a connected load of 4.5KW or are you planning to not use full power ie several

I did the same work last year in Frapa Marina, Rogoznica, all was very well done. You may check, if they have the capacity to perform the work in the next days. Happy sailing too, Hans SM2K #411

I had to remove about 50 members this morning because their email was bouncing or not working. If you received this email, obviously you are NOT removed. FYI, they were all Yahoo email addresses

Thanks for the responses. I talked to Bruntons and they agree that it is either the adjustment nut or the bearings may have seated since the rebuild. We are planning on removing the prop in water,

There is a great service.operation in Pula. Commodore and it is VAT free if.you are not EU flagged. I had quite a bit of.work done with them and it was all well done. Best Regards Jim Watkins Act II.

Good morning, Dubrovnik marina is part of ACI marinas in Croatia. They are, in Dubrovnik, very busy and one of the most expensive marinas in Croatia. I have done haul out in Marina Portoroz, Slovenia

Dubrovnik marina was pretty good sheltered and quiet. Denis and Julie Fortune A54 159

We may need to haul out due to an issue with our Brunton prop. While hailed we will do the bottom paint and C-drive seal and oil change too. Would appreciate recommendations for good haul out

Sorry the final list is: Lip Seals Ken 2 Taun 5 Nick 2 Michelle Day 2 Ian Geoffrey Bone 2 Dominique Sery 2 Biffi Stefano 3 Eric Opdeweegh 2 Vladan Bojic 2 Ken

Jose, I did try to contact you personally, but I don't think I have your correct email address (I received it from the manufacturer). I was a bit upset, because I thought you were ignoring my email.

Below are the people that sent emails first to pay for the seals. If you missed out you should get a new group of 10 owners and place a new PO. Ken 2 Taun 5 Nick 2 Michelle Day 2 Ian Geoffrey