Hi all, after almost three years working hard for refitting my 1980 Maramu, due to job questions I will not able to cruise intensivily as I had in mind when I bought her. So sadly, I must to sell her,

Hello all, do you know, please, the correct o-ring sizes ? I found the bearings , not the seals. SAV AMEL doesn't any more supply the kit. Thanks for infos and suggestions Giovanni Testa sv EUTIKIA

Hi all I appreciate that this is a long shot but we are currently completely overhauling our electrics around the chart table and a wiring diagram/ connections for the Lorenz 12 channel GPS antenna

I have an 1985 Maramu with a Perkins 4.154 that I had to replace a fresh water pump on last week. I had trouble finding the replacement pump and heard a lot of comments about "this is obsolete" and

We have the same AC problem. Have had several communications with the yard about the units freezing up and the only solution to date has been to take the units off auto and set the fans on the

Hi, Some of you have realized I was lately moderating the messages to all the group. The reason is that we had started to receive unwanted messages in our email addresses from the forum. I think I

I have had various sticks, rods and pipes that I have used to clean out the Sea Chest fill pipe and seacock, but none of them worked as good as the one that I recently fabricated. You can see a photo

Mike, I had good luck by calling Mastervolt in the Netherlands, phone 31-203422100. Ask for Edwin. I tried Mastervolt in Florida and they were not very helful. Good luck John " Moon Dog "

Markus, this is, as you are correctly stating, a common problem of the 54s. I can cope with it by reducing the temperature in 3 degree steps, as recommended by the yard. Martin Amel 54 # 149

I am looking for answers on SM2k anchor chain. Here is what I know about the anchor chain on SM #387: It is 10mm, ISO standard (the inside dimension the long-way of a link is 30mm...if it were DIN

Please note that Dimension Polyant manufactures two types of Hydranet cloth. One is a crosscut and the other is radial. The crosscut has not held up well so not too many sailmakers will recommend

Having sailed our new 54 first time in the Med this summer I have to express my big disappointment relating to the air-condition of the AMEL 54. All three of the units tend to get icy because they are

Would anyone have a source for metric-sized dinnerware that will fit into the built-in Amel Mango storage cabinet? We would rather not have to tear out the old shelves to accomodate non-metric

Hi Belitbh. I,m living ma SMM Excalibur in Marmaris Yacht Marin. Is the best one regarding price and I´ve change my engine Volvo Penta 75 hp for a Yanmar 110 hp . They did a very good job and very

I was in Yasmine Hammamet Marine this summer and due to a problem with my genoa I asked the marina office for a sail maker. They gave me the number for a Tunisian sail maker who did a very good job

We always had our general work done by Selmar Yacht Service in Turgutreis. Last year, we were on the hard stand at Yalikavak to have our rigging replaced by Sound Yachts. We had a major service done

thanks a lot and noted, we donnot have a problem with the bow thruster, but just need to service it...do you have any experience with the other items in the same places?

pls go to Kusadasi, Turky...this is the best place for wintering... Service will be done from www.internationalyachtservice.de.tl with kind regards IYS@...

I agree, I have seen some photos of there factory it is very important, and the price is very very competitive, I will probably go to Sousse in mai jluc CottonBay Le 28/09/2010 00:31, Bob Parry a

Hello to the Amel Yacht Owners group. We are relatively new owners of an Amel Maramu 1987, hull 225. We love our yacht and have greatly appreciated the rich exchange of information shared between