Judy and Bill,    I too am in Thailand, at YachtHaven, Phuket, and know of a local guy who has rebuilt my mixer elbow - twice.    He rebuilt the old one on my Perkins, in about a week in 2002, and

Bill, I recently had a similar problem which was due to a pinhole in the weld in the fabricated s/s exhaust/water mixing elbow on my Yanmar. I had a perfectly adequate

Hi Y'all, We have just had our turbo cleaned and also renewed the exhaust elbow on our 78 hp Volvo ( Pen Azen is SM 302) 10 years use and almost exactly 4,000 hours. In the last 6 months the

Gary, Mark and All Thanks for the messages. We are in Thailand getting ready to leave to start a 5,000 trip to the Med. I decided to take a close look at our mixing elbow becaue we have a long way

Gary, I purchased the ACR unit which interfaced very easily with my e80 and E-120 units. I mounted it near the Gps antenna on the stern rail and used a small gland fitting like Amel uses to bring the

Hello to all: To everyone on the Amel forum who has contributed to my Amel education, to the Amel factory team that built such a well conceived and well executed boat, and to Joel who has become my

Gary, I faced the same problem, I even wrote Davis Marine who makes the smaller sizes and they have no idea where to get it. Fair Winds Eric _____ From:

Eric: It has been a couple of years but I last purchased some of the larger size covers from Laurant in Amel Guadeloupe. They were no doubt sent from France. I bought about 20 pieces of each of

Has anyone installed a RayMarine AIS500? If so I have a couple of questions: 1. Did you have any trouble interfacing with your chart plotter, for instance I have a C80 at the helm. 2. Where did you

Mark: I purchased a exhaust elbow/water mixing injector Yanmar PN 129671-13551, for my Yanmar 4JH3-TE (Amel SM2000 Hull # 335, delivered July 2001) from Boatswain's Locker in Costa Mesa CA phone

Both our Yanmar and Onan wet exhaust mixer elbows are near the end of their lives. The prices for the OEM parts seem a bit high, even as boat parts go. Apparently, the previous owner of our boat

Merry Christmas you two, Bill will you send me an email address that I can talk to you in private. Please send to agav8ter (at) yahoo dot com. Thanks. I hope all is well with you and Judy. I

Thanks, Steve, That looks interesting. Cheers, Ian

I have been using first aid tape that you use to hold on gauze bandages. It is available in any pharmacy. Fair Winds Eric Amel Super Maramu #376 Kimberlite _____ From:

I have been unable to locate the cloth-like tape Amel wrapped on hoses under worm clamps throughout my SM2K. I've been using electrical tape when replacing it, vaguely worried I may be doing

Ian We encountered the same concerns as we sail in Maine during the summer time and the spurs are too small and zinc repacement is constant. We ordered the following line cutter Shart Shark Cutter and

Hi y'all, We have had Spurs rope cutters on Pen Azen ( SM 302) for ten years. On a couple of occasions we have encountered fairly thick rope and the fixed blade has just snapped off. Spurs

Hi y'all, We have had Spurs rope cutters on Pen Azen ( SM 302) for ten years. On a couple of occasions we have encountered fairly thick rope and the fixed blade has just snapped off. Spurs

Eric, The slit was the width of the sawblade. The material is flexible enough to work with so you just need the one cut. We've had ours on for over a year and they still look fine. We came back

Dave, I was thinking of that, However how long does it hold up in the Caribbean sun? Did you cut a very small slit ? or what size,? What did you seize it with? Fair Winds Eric _____