Hi Mark, I had a set built by QSails in Izmir, Turkey earlier this year. They are built from Hyrdanet, with Spectra webbings, Sunbrella UV protection, the Amel logo, and a foam luff

Hi Alex, I suspect from your reference to a para sail you are actually asking for advice regarding a Down wind sail, that is one that is used when the wind is from behind. Is that

How much is a set of sails? With best regards, Mark Super Maramu 2000 Hull #275 www.creampuff.us Currently cruising: Tampa Bay

Sorry Alexandre I don't have a photo and it may be some months before I have the motor back in there. When we bought the boat it had a 9.9 hp Mercury 4 stroke. That fitted as well. If I remember

Hi All, I bought an Onan elbow and gasket from jackssmallengines.com for less just 10 days ago: Part# 155326102 MIXER ELBOW 1 $407.98 A028X874 Gasket Exh Out Conn 2

Good morning Alex, The system that allow you to measure how many amps you are using, have used, or are charging. On the SM2K we have the Link 10, not sure on yours. I was thinking about your

We replaced our Genoa and all of our sails with a hydranet triradial cut sail made by a well established sail loft in Izmir Turkey. They ship world wide...several other owners have used the

I need toreplace my upwind sail and wabted to ask the forum for recommendations. I tend tostay with the AMEL system as is on AMEL54. Can anyone of you share which sail he recommendsto buy in this

Alexandre, thanks for your information. I'm not sure what you mean with "link 10". I'm new to the boat. Thanks for your help. Alex On Wednesday, December 14, 2016 2:49 PM, "Ben Driver/YAHOO

My pleasure Vladimir and Derick, I am glad this can help the group! As time goes I will make more of these! I purchase mine from Onan when I was in San Juan Puerto

Good morning Danny, When you get the chance, could you please send a picture! I also have the Yamaha Endure 15 HP (2 cycle) and I didn’t manage to make it fit vertically… So I lay mine down (which

Kent My Santorin came with a halfway halliard (a block at the spreaders) specifically to crane things out of the lazarette using either of the mizzenmast boom blocks. It's a godsend. Ian Ocean Hobo

We also do not pickle our water maker, having been dissatisfied with both SMBSulphite and propylene glycol. We flush with own freshwater for 45-60 sec (about 8 liters) after every use. For extended

Alexandere, Thank you very mych for your detail instructions with good photos. Your work is highly appreciated by all of us. Please advice where did you buy the elbow and how much it

Hi Danny, I do have that recess, but it still doesn't fit. I guess I gave a longer lower unit than you do. Kent Kent Robertson S/V Kristy karkauai@... Panama cell: +507-61171896 USA cell:

Hi Kent, I have the same motor as you and it does fit on the bracket and the lid closes. As I said before, with a wriggle or two. There is a round recess in the floor of the lazarette below that

Based on they previous recommendations and using Alexandre's wonderful pictures I just had the Onan exhaust elbow and manifold joint examined for carbon buildup. Sure enough, the manifold side was

I occasionally drop my outboard (a 15HP Yamaha 2-stroke) over the port rail or to put it in the aft lazarette. Mine does not fit on the bracket in the lazarette and allow the hatch to close. It's

Hi Mohammad, thanks for the pictures; it does indeed look very similar to ours, so I feel more comfortable it could fit a 20HP 4-stroke. I'll review my measurements. Thanks for the input! One more

Good morning Ben, If you look at the original Super Maramu owner manual (for vessel equipped with the 30 Amp and 50 Amp Dolphin) it said (using the genset) to start the 2nd charger 1 minute after the