Hi Dan, We do too. You've got to fall of a few degrees so the main just fills. It stops the roll and, with some breeze, adds another knot or so of speed. If no wind or straight into the wind, then no

Hi Eric, The light is the OGM (Orca Green Marine) LXTA-SP and they use 3 conductors. A shared negative then one positive for Tricolor, a second positive for Anchor, and both positives for strobe.

Mark & the Group, I am about to do this job on SM384 while she is still in the water. If you have a moment could you please tell us how the job went? I have Raymarine ST-60 instruments too. As best I

Peter Kinek Kinowski posted in Amel Yacht Owners . Peter Kinek Kinowski May 26 at 10:45am Tussen wal en schip Wow! Net niet tussen wal en schip Like Comment Share

Hi, I got my replacement gear from Amel. Regards Danny SM 299 Ocean Pearl (departing NZ for Fiji in a couple of weeks)

Looking at some major face lift to my Santorin (realised that I wouldn't be happy with any other unless will buy something for 3 times her value, which is obviously refitted SM 2000 year 2005),

Was wondering about the same on my Santorin 1992 (doing about 5.3-5.8) flat seas no current at 2800-3000), Check the following: a. Is your RPM counter calibrated? (I realised that my 3,000RPM is

A friend just told that AMFA was bought by a french company. He obtained parts (for his 54's bilge pump) from: SEIMI Rue Alain Colas 29200 Brest 02 98 46 11 02 FRANCE The teflon wheel (for the pomp

Hi Craig, How do you switch on the strobe without a dedicated wire to the strobe? My aquasignal has 4 connections. Ground, tricolor, anchor light, and strobe. Fair Winds Eric Kimberlite Amel Super

Hi, You can also try the Huntington Yacht Clun on Long Island sound. It is a very sheltered harbour. It is a 1 hour train ride to Manhattan. Just mention Kimberlite if you wish a mooring or

I bought Kimberlite with the tricolor/strobe installed. Amel put the switch next to the autopilot course computer. Fair Winds Eric Kimberlite Amel Super Maramu #376

Ian Just for my understanding: why do you mostly motor with the main set? For more speed? Best - Daniel SY HEUREKA SN 64 Kuşadası, Turkey

Drew, Be sure the part comes with a gasket. I have seen replacement elements shipped without a gasket. The old gasket will be deformed. Also, I believe that the heating element is somewhat universal

Hi Keith, Per a post I made a couple of years ago (19271): "when mine failed it was that the outer ring of gear teeth began to slip around the inner driven disc. The gear is actually two pieces with a

Kent, Thanks a lot for your reply. I like Jabsco pumps. I am looking forward to see your installation photos.

There are several Jabsco pumps that would work. I chose model 34600-0010, 24V, 3.5A, 10.8 gal/min. I will post a pic of it on the shelf I added to mount it where the old one was located. My float

Keith, The gap that you see in that white nylon gear is a missing/broken gear tooth. You need to replace the gear. The only place in the world that I know for sure that had some of these gears for

Hi Keith, I had that problem some years ago. The nylon gear ring goes around the inner nylon drive disc and relies on a fine toothed spline to keep it from slipping. With time that spline slips

Congratulations James ! This is very good when Michel was unsure of the answer he did research. Welcome to the family again! Alexandre --------------------------------------------

Vladimir, See post #24890 about this - you do not need an additional wire for the strobe. Cheers, Craig Briggs, SN#68 Sangaris ---In amelyachtowners@..., <sonsev52@...> wrote : Eric, Did you run