Go to portsmouth Ric Gottschalk Kitchen Magic Refacers, Inc Office 410-923-5800 Fax 410-923-5802 On Aug 22, 2015, at 10:35 AM, karkauai@... [amelyachtowners] <amelyachtowners@...> wrote:

Hi Kent the folks at New England Boatworks are the best. I'm here give a call Fair Winds Smooth Sailing To All Capt Richard RP Yacht Brokerage Newport RI We list sell and service fine yachts

Hi Kent, I have always enjoyed Potter Cove on the east side of Prudence Island. The ASM is too big to go into the cove, so anchor just south of the cove entrance in thick mud bottom. Or pick up a

Hi all, Will be going from WoodsHole to Newport RI where I'll spend a week or so. Does anyone have a favorite anchorage/mooring/marina in the area? I have some Stainless work to do while there,

Haha I think we will be investigating increasing the size of the demi UV panels at least Andrew Ronpische SM472 From: amelyachtowners@... [mailto:amelyachtowners@...] Sent: Saturday,

Andrew, For what is worth... The original sails on BeBe 387 were Demi sails. Shortly after buying BeBe I had larger UV panels made for the main and the mizzen because with the sails furled and the

Following discussions around this earlier in the year I checked our VIctron Quattro Invertor / Charger and found no connection between AC earth and -24V. In any case we also have an isolation

While we are sharing mistakes – I will share our more expensive mistake. We replaced our main and mizzen sails with hydranet vertical battened sails recently, having been assured by Demi sails

Hi JP, We look forward to checking it out when we are there next week. We won't be making decisions for a while, just gathering info ☺☺ Cheers Chris Hemera SM031

Hi Chris, We are in Goček and will meet in a few days. Obviously, gathering the information is important for your decision. Wait until you see what Eleuthera looks like then it might make your

IB5072 - Inductive sensor - eclass: 27270101 / 27-27-01-01 IB5072 - Inductive sensor - eclass: 27270101 / 27-27-01... Product characteristics Inductive sensor

Terrific - thanks for that Bill Cheers Chris Flack Hemera SM031 On 22-Aug-15 10:10 AM, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] wrote:

Eric, The original was IB5076 (3 wires). I used an IB5074 (2 wires). I am not familiar with the one you have. Bill BeBe 387 <amelyachtowners@...> wrote:

Chris, UltraSuede is better for berths, but if you use UltraLeather and have a very thick fiber layer (1.5 to 2") as a mattress pad, it might be OK for sleeping. You might want to test this fiber

Does anyone know about a chain counter sensor same manufactureras my dead one but with a model number IB5072 Fair Winds Eric

Hi Bill, Further to the upholstery questions, what have you got, or what would you recommend, for the back and seat cushions throughout the rest of the boat? We are leaning towards

Bill, I have a new model 5072 with 3 wires. I don't understand your instructions. Please explain. Fair winds, eric

Bill, I did the same thing last year—Just lazy I guess. I also changed the O ring on the drain plug and put some sealant between the outside of the drain plug and the C-Drive body. Just in case

Hanspeter, No bonding to the arch. I don't need to check, I was there and participated in the wiring of the arch solar panels. Bonding is not necessary. I don't use the arch to lift the dinghy and I

Hi Bill Concerning bonding ! How Emek, Riza, make the bonding of the Inox Arch on your boat? You checked it? Second Question to all Emek Arch Owner; how you Lift the dingy with lets say a dingy Motor