I am not sure about Amel being the reason because the Isotemp Basic 40 on BeBe was replaced while we were in New Zealand...Amel did not touch this one. Isotemp is doing something with those wire

Just for your info. The wire ties you found in the water heater come from the fact that, in the old days, Amel used to install magnesium anodes inside the water heater. These anodes were tied to the

Good morning Will, I have the D-60 and my experience is very small on water maker. After the water maker person changed the membrane (and the “high pressure” switch which was not working), my

All models are pretty much the same apart from membrane numbers and pump capacity... When you say it "turns itself off", does that mean the circuit breaker (diruptor) "dessalinateur" trips ? Or does

Check that the pre-filter is filled with water. If you changed that in the same time it takes some time to get the water through the pre-filter since it has to be really soaked. Also check the sensor

Hi Will: I am a bit unfamiliar with the D50 but have some experience with the 220 VAC 50 Hz 120 liter/hr Dessalator water maker. Is the D50 a 220 VAC water maker? How many liters/hr does it

Hi, I recently had my membranes replaced on my desalanator D50 (1996) the unit worked fine for a few days and then started turning itself off. Any ideas out there as to what I might look at a the

Hi Leo, I can't thank you enough for going to all this trouble for me. I'll try spraying the timer. Do you have the name and email address of the person you talked to at Schabauer in case I decide to

Hi James, yes your ballast should be bonded. Probably in the eighties, AMEL did not put a copper strap but a copper braid with a terminal connected (bolted on one of the keel bolts inside the grey

Peter, Tinley Electronics (http://www.tinleyelectronics.com/) in the UK is the authorized repair depot. They will repair or rebuild aything. Email "Sarah Pidgley"

Hi Kent, Did you get the Iridium :Go" setup? If so, then the WiFi data is autonomous from the phone. Thew ay I understand this Axcess Point setup is that the router has to actually dial the phone

Hi Peter, My SM is also a 1992, and for now the B&G instruments are working. Recently, both of my multi function displays were difficult to read, and the buttons were not working well. I took them

Gary, Good question - I would like to know the answer if you get it as I have a similar set upon my 54. Peter Peter Forbes 0044 7836 209730 ppsforbes@... Carango Sailing Ketch Amel 54 #035 Travelling

Hello, I got the B&G instruments, transducers and sensors and the Hydra 330 installed on my SM (build 1992). The processor does no longer work and after calling into B&G UK, I learned that there is no

Hi Olivier, Still looking at the bonding and came across the below. Do you know should there be a bilge strap on a Maramu 46. The keel is bolted so I presume it should be bonded. As far as I can

Hi Gary, I just received the same equipment as you have. I have sent emails via the wifi access point, and made calls with the phone, not using the access point. I haven't tried using the phone

Hello, I know this is off topic of our boats, but I am working with an Iridium 9575 (Extreme) and an Iridium Axcess Point router ((WiPipe) and they are giving me geek-fits tonight. Wondering if

Hello Mr. Romano, I apologize for my late reply. In the photos it is indeed the propellant that we installed on our boats. Can you tell me which parts you need, knowing that we cannot provide

Hi I have written to Amel Med for same reason. This is the reply. ================================================================================================ Bonjour Monsieur Romano,

Good afternoon James, bonding all the metallic items that are in touch with seawater helps fighting galvanic corrosion. This concerns mainly the items under waterline, but also the fuel tank and