Hi Peter, We did a lot of research on Coppercoat before applying it to Pen Azen our SM 302 when she was 9 years old. We had the hull dry sand blasted. Very impressive for its accuracy

Since new shutting down my Yanmar 100 HP engine on my Super Maramu 2000 (414) has been erratic. When the red stop button is pushed it can take up to 20 seconds for the engine to stop. Very irritating

Peter, You may want to read message number 2990 by Joel Potter describing the keel epoxy process: http://groups.yahoo.com/group/amelyachtowners/message/2990 You may want to check the photo in the

Hi once out of the water let her dry a bit while you do some other work. The soda blast or nut shell blast remove all the old paint. Then check with the copper coat folks and seal the bottom

Hello all, By the end of september I will be the very happy owner of Amel Maramu #162. It took me about a year to find my dreamboat but now I'm convinced that I've found her. Of course there is some

Maramu #91 Popeye is now at her new home in Port Douglas. Two of us sailed the 800 miles from Brisbane in 6 days including one stop in Mourylian for 12 hours (to time our arrival for the day time for

We changed to Dyneema and reduced the diameter to 14mm and 12mm for the main sheet. The latter is a much better fit on the jammer on the winch. Anne and John Bali Hai SM 319

The dimension I got from Amel was 16 mm by 42 meters. Many people have changed to dyeem.(sp). Fair Winds Eric Amel Super Maramu #376 Kimberlite _____ From:

We need to replace the genoa sheet on our SMM. Before storing the boat last June for hurricane season, I measured the length of the original sheet (39meters, port + strbd), but I forgot to measure

Hi, Eric, On KRISTY (SM2K#243) the freezer/fridge units under the dinette seats are Frigoboat model # AV35F.  I've just looked on line and can't find a number for the compressor, although I do have

_____ From: amelyachtowners@... [mailto:amelyachtowners@...] On Behalf Of kimberlite Sent: Saturday, July 30, 2011 3:38 AM To: amelyachtowners@... Subject:

Jim, Sorry I do not have the number but is listed as an option on the newer parts manual pages. Here in the USA it was about $1400- Fair Winds Eric Amel Super Maramu #376 Kimberlite _____

Hi Eric, Good information, thank-you. I had the same problem and had Amel's engine subcontractor weld it up for me in Hyeres. However after about 200 hours of use, although I cannot detect any gas

Hi, I went into the dingy to look at the Chain plate/tang. I saw nothing but unblemished rectangular stainless. Fair Winds Eric

_____ Sent: Tuesday, August 02, 2011 10:53 PM To: 'amelyachtowners@...' Subject: new yanmar optional exhaust elbow After much research I received the "optional " exhaust elbow. My

After much research I received the "optional " exhaust elbow. My last 3 on the 4jh3hte rotted out at the welds and had pinpoint holes. This one is a massive casting probably weighing 10 pounds or

Jose do you have some photos? Fair Winds Eric Amel Super Maramu #376 Kimberlite _____ From: amelyachtowners@... [mailto:amelyachtowners@...] On Behalf Of

There is an o-ring on ours. Heat some water on the stove and place the o-ring in the hot water prior to install. Our impeller supplier provides the new o-ring in the package.

use silicone grease or spray to install the impeller. Oil based lubricants do damage to the impeller. fw eRic sm 376

I have a friend in the Barcelona area that has a well cared for Super Maramu, hull #288, that is going on the market soon. He can be contacted at jaume"at"bionic.es. He is not a member of the Amel