HiRoger, first of all I think the ICOM IC-M 802 is about the best of units you can get these days, however, it might be illegal for a non-ham to fit it - at least in germany it is not approved as a

Thanks for the reply, Ian and Judy. We did use the 15W40 because that was all we could locate near the boatyard. We also did replace the hard interior seal on the bowthruster when we replaced the

Dear all, I'm most probably going to be fitting an Icom M802 SSB, enabled for the Ham frequencies. SSB is fairly new to me so I wonder if some of you seasoned adventurers could give me some advice on

Erick, merci pour vos conseils. Je contacterai Bauer France quand Amel commence avec la construction de mon bateau en 2008. However, for the benefit of all the English speakers here, perhaps better if

Could you pls send me your tel number as I am interested for this summer. Many thanks carl bauer +44 7767 291 048 --- Krassopoulos Dimitris <dkra@...>

22 Mar 2006 Eric: On my bow thruster the flat side of the seal faced the sea water and propeller, while the concave side with the spring faced the recess in the bow thruster. The bow thruster

I was able to remove the heating element and the zinc without removing the whole heater from the engine room. I just dis-connected the electric. I then ran the water till the water in the tank was

Vito, The lip seal on the bow thruster’s propeller shaft has 2 sides one flat side and one concave side with a spring showing. Which side faces the sea water and propeller? Fair

Hi, My Amel Super Maramu #376 Kimberlite has electronic sensors on the bow thrusters lift assembly . They are attached with clamps around the assembly. What do theses sensors do and how are they

Bonjour Roger Le contact que j'avais chez Bauer est Nathalie Pechoux Tel. +33 479 88 71 69 npechoux@... Pour information le tuyau haute pression de remplissage doit mesurer environ

Dear Ian and Erick Thanks for the feedback on the Bauer compressor. I'm definitely going to ask Amel to install it then! Yes, they are noisy things so we may not be terribly popular at some

Hi Judy, When we bought Pen Azen new we were told 15W40 and it seems to have worked happily ever since. Incidentally, as well as the two external and one internal soft foam rings to be replaced on

The motor on furler on the main sail is making a lot of noise. Is there anyone out there that has had this problem and what did you do about it. Thanks James DeSalvo

We are looking into buying a Super Maramu, and I would like to see the stability curve, or GZ curve, or at least know the angle of vanishing stability. The GZ curve describes the resistance to

I disconnected the cold water at each faucet and turned the pump on and this cleared the problem although I did not see anything apparent released. At any rate, the pressure is back to

Thank You gary This is very helpfull. Vito wrote: (Reverse Osmosis) a rather bought processes. This production was a drop cost. Dessalator, Water, and the same. I is 776-461-0256. site shows

As far as I can determine there is only one manufacturer of RO (Reverse Osmosis) membranes in the world. That manufacturer is FilmTec. FilmTec was a rather small company that manufactured membranes

Hi Vito, How many hours have you done on your watermaker and is it the 60 or 150l p h version? We test ours just by drinking it and after 1300 hours its fine. We lay up now for about 6 months of the

FROM: "LADY DIVINA" SM317 I FOUND THAT AN ADJUSTMENT TO THE BOWTHRUSTER ON SM317 SOLVED THE SEAWATER INTRUSION PROBLEM WHILE AT SEA. I LOWERED THE BOLT(w/PIN HOLE) ON TOP OF THE MOTOR UNIT BY

Hello from Fiji Well of course problems will crop up in the most remote places. I recently bought a water saltinity tester. The water coming from the watermaker is testing at 1200 PPM. The water from