|
Re: Yanmar 4jh3-hte overheat
Duane,
Generally, temp sensors work off of resistance with high resistance when cold and much lower resistance as the medium gets hotter. You can use a cup of room temperature water and boiling water
Duane,
Generally, temp sensors work off of resistance with high resistance when cold and much lower resistance as the medium gets hotter. You can use a cup of room temperature water and boiling water
|
By
Mark McGovern
·
#49170
·
|
|
Re: Yanmar 4jh3-hte overheat
Bill,
I'll check the transmission cooler, good advice. That wasn't the primary cause though, as I noted, the engine seawater pump had shed all of its vanes.
Duane
Bill,
I'll check the transmission cooler, good advice. That wasn't the primary cause though, as I noted, the engine seawater pump had shed all of its vanes.
Duane
|
By
Duane Siegfri
·
#49169
·
|
|
Re: Yanmar 4jh3-hte overheat
Check the sea chest side of the transmission oil cooler. This should be cleaned every 2 years. Small pieces of debris that get past the sea chest strainer will block water from flowing through this
Check the sea chest side of the transmission oil cooler. This should be cleaned every 2 years. Small pieces of debris that get past the sea chest strainer will block water from flowing through this
|
By
CW Bill Rouse
·
#49168
·
|
|
Yanmar 4jh3-hte overheat
We had an overheat condition on our engine (Yanmar 4JH3-HTE) and the alarm light or buzzer did not sound. I checked the parts manual and the temperature sensor is a 100 oC sensor. I noticed the
We had an overheat condition on our engine (Yanmar 4JH3-HTE) and the alarm light or buzzer did not sound. I checked the parts manual and the temperature sensor is a 100 oC sensor. I noticed the
|
By
Duane Siegfri
·
#49167
·
|
|
Re: Lens-shaped bolt nuts
Gerhard,
These same nuts are used all over my Maramu, many thanks for posting a source. I will add this to my file.
James
SV Sueno
Maramu #220
Gerhard,
These same nuts are used all over my Maramu, many thanks for posting a source. I will add this to my file.
James
SV Sueno
Maramu #220
|
By
James Alton
·
#49166
·
|
|
Re: Cracks on bow sprit
Thank you very much for all feedback re. crack at the bow. Once I get feedback from AMEL will share with all.
Best regards
--
Jarek Zemlo
Thank you very much for all feedback re. crack at the bow. Once I get feedback from AMEL will share with all.
Best regards
--
Jarek Zemlo
|
By
Jarek Zemlo
·
#49165
·
|
|
Re: Desperate plea for an alternator/charging problem - Amel Euros 41, 1976, MD21a engine
Good to know on that also re the 24V.
Good to know on that also re the 24V.
|
By
Andrew Eaves <andyeaves@...>
·
#49164
·
|
|
Re: Down wind pole corrosion damage
Bill- thanks as always for your info and speculation. The rivets all over the pole are quite brittle with heads falling out so I'm concerned water ingress and corrosion played a large part. I found
Bill- thanks as always for your info and speculation. The rivets all over the pole are quite brittle with heads falling out so I'm concerned water ingress and corrosion played a large part. I found
|
By
Thomas Kleman
·
#49163
·
|
|
Deck Repairs to Amel Mango
Hello all,
I am contemplating the repair of the decks of my Amel Mango. The cracks seem to go down some way.
I was wondering if anyone had any experience with repairs of this nature and what process
Hello all,
I am contemplating the repair of the decks of my Amel Mango. The cracks seem to go down some way.
I was wondering if anyone had any experience with repairs of this nature and what process
|
By
Ian Bone
·
#49162
·
|
|
Lens-shaped bolt nuts
I don't know if Amel has used these lens-shaped bolt nuts for their other or later boats but I have them found at several places in my Sharki.
After searching for a long time I have found them at this
I don't know if Amel has used these lens-shaped bolt nuts for their other or later boats but I have them found at several places in my Sharki.
After searching for a long time I have found them at this
|
By
Gerhard Mueller
·
#49161
·
|
|
Volvo D3 110i-A raw water pump and damper
Regarding replacing the Raw water pump Volvo 21141637
It looks like there is also the option of the Johnson pump VP0030DA as a replacement that is about half the price of the Volvo one. Thanks for
Regarding replacing the Raw water pump Volvo 21141637
It looks like there is also the option of the Johnson pump VP0030DA as a replacement that is about half the price of the Volvo one. Thanks for
|
By
ngtnewington Newington
·
#49160
·
|
|
wiring of the genset fan
---------- Original Message ----------
From: eric <kimberlite@...>
To: Amel Owners <main@amelyachtowners.groups.io>
Date: November 11, 2019 at 10:13 PM
Subject: wiring of the genset fan
---------- Original Message ----------
From: eric <kimberlite@...>
To: Amel Owners <main@amelyachtowners.groups.io>
Date: November 11, 2019 at 10:13 PM
Subject: wiring of the genset fan
|
By
eric freedman
·
#49159
·
|
|
Re: wiring of the genset fan
On November 11, 2019 at 10:13 PM eric <kimberlite@...> wrote:
Bill,
The Load (the fan ) is connected to the to the capacitor as well as the brown wire both being in parallel are then connected
On November 11, 2019 at 10:13 PM eric <kimberlite@...> wrote:
Bill,
The Load (the fan ) is connected to the to the capacitor as well as the brown wire both being in parallel are then connected
|
By
eric freedman
·
#49158
·
|
|
wiring of the genset fan
Bill,
The Load (the fan ) is connected to the to the capacitor as well as the brown wire both being in parallel are then connected to the other side of the fuse.
The black wire is hooked up to the
Bill,
The Load (the fan ) is connected to the to the capacitor as well as the brown wire both being in parallel are then connected to the other side of the fuse.
The black wire is hooked up to the
|
By
eric freedman
·
#49157
·
|
|
Re: Wave slap / banging under the stern
Hi Matt;
We’re not on board. Will look through photos to see if I have one to post.
Happy Sailing;
Mohammad and Aty
B&B Kokomo
AMEL 54 #099
Hi Matt;
We’re not on board. Will look through photos to see if I have one to post.
Happy Sailing;
Mohammad and Aty
B&B Kokomo
AMEL 54 #099
|
By
Mohammad Shirloo
·
#49156
·
|
|
Re: Antal 120x18 Composite Fibre jib block
Thanks for the replies. I soaked and rinsed and they have improved markedly. I plan on adding a lube as well.
Thanks for the replies. I soaked and rinsed and they have improved markedly. I plan on adding a lube as well.
|
By
Duane Siegfri
·
#49155
·
|
|
Re: Raw water pump on Volvo D3
Or but this: https://bigblueoceanmarine.com/jpr-vp0030da-jmp-marine-volvo-penta-replacement-engine-cooling-pump-replaces-volvo-penta-21141637/
I bought one and could not see the difference with the VP
Or but this: https://bigblueoceanmarine.com/jpr-vp0030da-jmp-marine-volvo-penta-replacement-engine-cooling-pump-replaces-volvo-penta-21141637/
I bought one and could not see the difference with the VP
|
By
Arno Luijten
·
#49154
·
|
|
Re: Antal 120x18 Composite Fibre jib block
Hi,
I grase my cars and blocks with "Harken one Drop" it is excellent!
Arnold
SY Zephyr
SM 203
Am 11.11.2019 um 23:06 schrieb Joerg Esdorn via Groups.Io <jhe1313@...>:
I asked Antal how to service
Hi,
I grase my cars and blocks with "Harken one Drop" it is excellent!
Arnold
SY Zephyr
SM 203
Am 11.11.2019 um 23:06 schrieb Joerg Esdorn via Groups.Io <jhe1313@...>:
I asked Antal how to service
|
By
Arnold Mente
·
#49153
·
|
|
Re: Antal 120x18 Composite Fibre jib block
I asked Antal how to service the blocks on my boat. They said rinsing with fresh water and a little grease.
joerg esdorn
A55 Kincsem
I asked Antal how to service the blocks on my boat. They said rinsing with fresh water and a little grease.
joerg esdorn
A55 Kincsem
|
By
Joerg Esdorn
·
#49152
·
|
|
Re: Wave slap / banging under the stern
We use swimming noodles as well (cut into smaller pieces so they closely follow the curvature of the hull).
Dennis
Libertad
Maramu 121
We use swimming noodles as well (cut into smaller pieces so they closely follow the curvature of the hull).
Dennis
Libertad
Maramu 121
|
By
sbmesasailor
·
#49151
·
|