|
Re: [Amel Yacht Owners] Bow locker seals
Thanks Kent,
The seals and some other stuff should be here tomorrow.
I will install them in the heat of the Caribbean.
Thank you so much !
Fair Winds
Eric
Kimberlite Amel Super Maramu #376
Thanks Kent,
The seals and some other stuff should be here tomorrow.
I will install them in the heat of the Caribbean.
Thank you so much !
Fair Winds
Eric
Kimberlite Amel Super Maramu #376
|
By
eric freedman
·
#48581
·
|
|
Re: SM2K: Replacing a CLIMMA 9EH AC unit in the Salon
#replacement
Hi Eric,
Thanks for the lead on an almost “plug and play” idea with Dometic 10.
Can you share some model details?
model number, power, supplier, etc.
Much appreciated
Bob
Nomad Amel Super Maramu
Hi Eric,
Thanks for the lead on an almost “plug and play” idea with Dometic 10.
Can you share some model details?
model number, power, supplier, etc.
Much appreciated
Bob
Nomad Amel Super Maramu
|
By
Bob Ross
·
#48580
·
|
|
Re: Access behind the Eno Stove Oven
Hi Soraya,
I did this as well. Make sure you remove the stainless guard tube in front before removal. Next use books or whatever to put under the stove to take the weight off the hinges. The
Hi Soraya,
I did this as well. Make sure you remove the stainless guard tube in front before removal. Next use books or whatever to put under the stove to take the weight off the hinges. The
|
By
Arno Luijten
·
#48579
·
|
|
Re: mizzen traveller
Nicely done Bill.
I wander if anyone has upgraded the traveler car. It seems to me that it is not possible to remove the old car and ad the new one without separating the track from the deck or
Nicely done Bill.
I wander if anyone has upgraded the traveler car. It seems to me that it is not possible to remove the old car and ad the new one without separating the track from the deck or
|
By
Jose Venegas
·
#48578
·
|
|
Re: Companion way for removal
Courtney,
Good idea.
Best,
CW Bill Rouse
Amel Yacht Owners School - www.AmelYachtOwnersSchool.com
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970
Courtney,
Good idea.
Best,
CW Bill Rouse
Amel Yacht Owners School - www.AmelYachtOwnersSchool.com
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970
|
By
CW Bill Rouse
·
#48577
·
|
|
Re: mizzen traveller
Paul,
Bill Kinney did a blog post about how he did it on SM Harmonie: https://fetchinketch.net/boat-projects/mizzen-traveler/
--
Mark McGovern
SM #440 Cara
Deale, MD USA
Paul,
Bill Kinney did a blog post about how he did it on SM Harmonie: https://fetchinketch.net/boat-projects/mizzen-traveler/
--
Mark McGovern
SM #440 Cara
Deale, MD USA
|
By
Mark McGovern
·
#48576
·
|
|
Re: Companion way for removal
Just a thought as I have no experience in removing the dodger but if you could thread braided fishing line between the dodger and the deck then you could tie 'Handles' to both ends and 'saw' through
Just a thought as I have no experience in removing the dodger but if you could thread braided fishing line between the dodger and the deck then you could tie 'Handles' to both ends and 'saw' through
|
By
Courtney Gorman
·
#48575
·
|
|
Sharki Mast Pad?
Hi, I plan to remove the masts on Sea Hobo, Sharki 96 over the next 3 months at Cardiff Marina Village. I can see no signs of a pad under either mast, is there one on a Sharki? We will re-use the
Hi, I plan to remove the masts on Sea Hobo, Sharki 96 over the next 3 months at Cardiff Marina Village. I can see no signs of a pad under either mast, is there one on a Sharki? We will re-use the
|
By
marklesparkle59
·
#48574
·
|
|
mizzen traveller
Hello!
I'm planning to arrange so that I can control the Mizzen traveller from the cockpit. does anyone now who have made the track? I need to add end "stop" with sheaves. all advice highly
Hello!
I'm planning to arrange so that I can control the Mizzen traveller from the cockpit. does anyone now who have made the track? I need to add end "stop" with sheaves. all advice highly
|
By
Paul Osterberg
·
#48573
·
|
|
Re: Companion way for removal
Hi Dieter,
We apply beeswax to the companionway door generously every time we lay the boat up. We also have a winter cover which stops sunlight falling directly on it. After 19 years the laminate
Hi Dieter,
We apply beeswax to the companionway door generously every time we lay the boat up. We also have a winter cover which stops sunlight falling directly on it. After 19 years the laminate
|
By
ianjenkins1946 <ianjudyjenkins@hotmail.com>
·
#48572
·
|
|
Re: Main mast seal/pad replacement
#replacement
#solution
Hi Barry
Thanks for sharing your experience, great Job done! But I can not see the photos. There is no photos attached or on the photo section.?
Maybe the upload did'nt work or some problems on the
Hi Barry
Thanks for sharing your experience, great Job done! But I can not see the photos. There is no photos attached or on the photo section.?
Maybe the upload did'nt work or some problems on the
|
By
Rudolf Waldispuehl
·
#48571
·
|
|
Re: Access behind the Eno Stove Oven
Good morning Soraya,
Here are the instruction for the SM2K, may be the same idea for the 54.
Good morning Soraya,
Here are the instruction for the SM2K, may be the same idea for the 54.
|
By
Alexandre Uster von Baar
·
#48570
·
|
|
Re: Companion way for removal
Thanks Eric,
I was thinking of maybe someone invented a wax with particles in it to protect a surface from being destroyed by UV. Could be a big market. The mention of automobile supply is very
Thanks Eric,
I was thinking of maybe someone invented a wax with particles in it to protect a surface from being destroyed by UV. Could be a big market. The mention of automobile supply is very
|
By
INUS - BUSCH
·
#48569
·
|
|
Re: Companion way for removal
Dear Dieter,
I just use a UV preventive hard wax. I get it at an automotive supply.
I believe a number of members use Polytrol on the decks. After reading Joel Potters comments, I thought I should
Dear Dieter,
I just use a UV preventive hard wax. I get it at an automotive supply.
I believe a number of members use Polytrol on the decks. After reading Joel Potters comments, I thought I should
|
By
eric freedman
·
#48568
·
|
|
Amel Board messages--Just a recollection.
When I first received Kimberlite in 2003 there were if I remember correctly,
about a total of about 150 messages a month on this board .
The number of communication now is impressive.
Fair
When I first received Kimberlite in 2003 there were if I remember correctly,
about a total of about 150 messages a month on this board .
The number of communication now is impressive.
Fair
|
By
eric freedman
·
#48567
·
|
|
Re: Companion way for removal
Precise, extensive and poetic description of an intimidating operation ;-)
Thanks a lot Craig !
F.
Precise, extensive and poetic description of an intimidating operation ;-)
Thanks a lot Craig !
F.
|
By
scentstone
·
#48566
·
|
|
Access behind the Eno Stove Oven
Hello,
I am considering dismounting the Eno Stove Oven as it seems the only way to properly access and clean the area behind it.
Does it sound like an overkill? any workarounds?
How easy is it to
Hello,
I am considering dismounting the Eno Stove Oven as it seems the only way to properly access and clean the area behind it.
Does it sound like an overkill? any workarounds?
How easy is it to
|
By
Sv Garulfo
·
#48565
·
|
|
Re: Onan MDKD 6.5kW genset exhaust elbow
Hi Karen,
We have a spare.. but we’re in Fiji...
Kind regards,
Jean-Pierre Germain,SY Eleuthera, Fiji.
Hi Karen,
We have a spare.. but we’re in Fiji...
Kind regards,
Jean-Pierre Germain,SY Eleuthera, Fiji.
|
By
Germain Jean-Pierre
·
#48564
·
|
|
Re: Onan MDKD 6.5kW genset exhaust elbow
Karen,
I've got a two JB Weld patches on engine pipes that are now "manufacturer discontinued" . The patches are, I can't remember exactly, about 15 years old and seem to be as good as new. If your
Karen,
I've got a two JB Weld patches on engine pipes that are now "manufacturer discontinued" . The patches are, I can't remember exactly, about 15 years old and seem to be as good as new. If your
|
By
Craig Briggs
·
#48563
·
|
|
Onan MDKD 6.5kW genset exhaust elbow
Does anyone have an exhaust elbow for an Onan 6.5kW MDKD generator exhaust elbow? Onan considers it an "obsolete part" and the price they want for it is mind-numbing... This is for the older, smaller
Does anyone have an exhaust elbow for an Onan 6.5kW MDKD generator exhaust elbow? Onan considers it an "obsolete part" and the price they want for it is mind-numbing... This is for the older, smaller
|
By
Karen Smith
·
#48562
·
|