|
Re: [Amel Yacht Owners] Winter location Greek Ionian
Hi,
I keep my boat in KALAMATA.
Maybe it is not quite Ionian but very close to.
It is very quiet place, some work place avaliable in marina.
KTel bus service avalible almost every hour to Athens.
Hi,
I keep my boat in KALAMATA.
Maybe it is not quite Ionian but very close to.
It is very quiet place, some work place avaliable in marina.
KTel bus service avalible almost every hour to Athens.
|
By
Marek Cho
·
#42333
·
|
|
Re: [Amel Yacht Owners] Winter location Greek Ionian
For storage ashore Preveza is good with two big yards Cleopatra and one next door.
I left my last boat there and it was good.
Nick Amelia (54)
For storage ashore Preveza is good with two big yards Cleopatra and one next door.
I left my last boat there and it was good.
Nick Amelia (54)
|
By
ngtnewington Newington
·
#42332
·
|
|
Re: [Amel Yacht Owners] Winter location Greek Ionian
Hi Mohammad, hi Aty,
I stay in the Marina Lefkada in Lefkda for many years. It is a very safe place with nice people and some companies, which can provide service. It might be not the cheapest
Hi Mohammad, hi Aty,
I stay in the Marina Lefkada in Lefkda for many years. It is a very safe place with nice people and some companies, which can provide service. It might be not the cheapest
|
By
Andreas
·
#42331
·
|
|
Goit Deck Hatch Lens Reseal
Has anyone else had the need to re-seal the lens into one of the Goit deck hatches? I just had one pop loose.
I've reset the lenses of other brands before, bedding them down in silicone, but just
Has anyone else had the need to re-seal the lens into one of the Goit deck hatches? I just had one pop loose.
I've reset the lenses of other brands before, bedding them down in silicone, but just
|
By
greatketch@...
·
#42330
·
|
|
Winter location Greek Ionian
Hi everyone;
We are looking at leaving our boat in the Greek Ionian for this winter. We would appreciate all input about possible locations. We will not be wintering on board, so we are mainly
Hi everyone;
We are looking at leaving our boat in the Greek Ionian for this winter. We would appreciate all input about possible locations. We will not be wintering on board, so we are mainly
|
By
Mohammad Shirloo
·
#42329
·
|
|
Re: [Amel Yacht Owners] Steyr engine
Definitely agree with Mark (as always),
Therefore I would be concerned with the Volvo D3-110 lack of reliability, I am sure you have read the issues on this forum or the (FB) Amel Owner Group.
Because
Definitely agree with Mark (as always),
Therefore I would be concerned with the Volvo D3-110 lack of reliability, I am sure you have read the issues on this forum or the (FB) Amel Owner Group.
Because
|
By
Alexandre Uster von Baar
·
#42328
·
|
|
Re: [Amel Yacht Owners] Steyr engine
That is the point.
I am sure AMEL can help with service but Steyr is well known here in Europe but in Panama or Cook Island?
That it can be good choice unless it is maintenance-free and reliable
That is the point.
I am sure AMEL can help with service but Steyr is well known here in Europe but in Panama or Cook Island?
That it can be good choice unless it is maintenance-free and reliable
|
By
Marek Cho
·
#42327
·
|
|
Re: [Amel Yacht Owners] Steyr engine
Mark,
I think the biggerdecision really depends on where you plan to take your boat. One of the reasonsboat manufacturers chose Yanmar, Volvo, Onan etc. is because of the globalnetwork of
Mark,
I think the biggerdecision really depends on where you plan to take your boat. One of the reasonsboat manufacturers chose Yanmar, Volvo, Onan etc. is because of the globalnetwork of
|
By
Mark Erdos
·
#42326
·
|
|
Steyr engine
Hi,
I am on market for Amel and there are two boats in which I am interested in.
The question is about engine. Both got Steyr 140hp engine.
As this is not very popular one in marine industry I
Hi,
I am on market for Amel and there are two boats in which I am interested in.
The question is about engine. Both got Steyr 140hp engine.
As this is not very popular one in marine industry I
|
By
Marek Cho
·
#42325
·
|
|
Re: [Amel Yacht Owners] Mechanics in Leros, Greece
Hajo,
good to meet you on the dock this morning! Welcome to Leros marina. For the benefit of others who might be considering coming here, I have asked around about the Amel knowledge
Hajo,
good to meet you on the dock this morning! Welcome to Leros marina. For the benefit of others who might be considering coming here, I have asked around about the Amel knowledge
|
By
Ian Shepherd
·
#42324
·
|
|
Re: [Amel Yacht Owners] Mechanics in Leros, Greece
Hi to all supporters,
Thanks a lot to all of you for the valuable informations.
So I am not really at the right spot to let the planned work to be done.
Yes, Bill, I had one of the best teachers 😃
Hi to all supporters,
Thanks a lot to all of you for the valuable informations.
So I am not really at the right spot to let the planned work to be done.
Yes, Bill, I had one of the best teachers 😃
|
By
Hajo Hille
·
#42323
·
|
|
Re: Vetus K018 Suppliers
Thanks Bill, I have left them a message.
For Eric it is these. The little rubber donuts that go in the vetus coupling between shaft and transmission
Thanks Bill, I have left them a message.
For Eric it is these. The little rubber donuts that go in the vetus coupling between shaft and transmission
|
By
Alan Grayson
·
#42322
·
|
|
Re: Vetus K018 Suppliers
Also...
https://www.fisheriessupply.com in Seattle carries them--and lots of other good stuff!
Bill Kinney
SM160, Harmonie
Annapolis, MD, USA
Also...
https://www.fisheriessupply.com in Seattle carries them--and lots of other good stuff!
Bill Kinney
SM160, Harmonie
Annapolis, MD, USA
|
By
greatketch@...
·
#42321
·
|
|
Re: [Amel Yacht Owners] Vetus K018 Suppliers
Hi ,
What is the Vetus K018?
Fair Winds
Eric
Kimberlite Amel Super Maramu #376
Hi ,
What is the Vetus K018?
Fair Winds
Eric
Kimberlite Amel Super Maramu #376
|
By
eric freedman
·
#42320
·
|
|
Re: [Amel Yacht Owners] Vetus K018 Suppliers
Alan,
You might try:
Vetus Marine 135 Imperial Street | Merritt Island, FL 32952 Office: 321-454-3375.
If they do not have, maybe they will order.
Best,
CW Bill Rouse
Admiral, Texas Navy
Commander
Alan,
You might try:
Vetus Marine 135 Imperial Street | Merritt Island, FL 32952 Office: 321-454-3375.
If they do not have, maybe they will order.
Best,
CW Bill Rouse
Admiral, Texas Navy
Commander
|
By
CW Bill Rouse
·
#42319
·
|
|
Vetus K018 Suppliers
Hi All, i'm trying to find a supplier for the Vetus Kit K018 in The good ole USA but can't seem to find any. Vetus shop in the UK keeps popping up. Does anyone know where i can source
Hi All, i'm trying to find a supplier for the Vetus Kit K018 in The good ole USA but can't seem to find any. Vetus shop in the UK keeps popping up. Does anyone know where i can source
|
By
Alan Grayson
·
#42318
·
|
|
Re: [Amel Yacht Owners] Re: Interior wood quality
Hi Bill,
We have owned a number of classic wooden vessels with lots of exterior varnishwork along with customer boats with even more. Mahogany (especially African and Phillipine) tend to lighten
Hi Bill,
We have owned a number of classic wooden vessels with lots of exterior varnishwork along with customer boats with even more. Mahogany (especially African and Phillipine) tend to lighten
|
By
James Alton
·
#42317
·
|
|
Re: At postage costs to have AIS receiver
All,
The AIS receiver has found a new home.
Cheers,
Arno
Luna, A54-121
All,
The AIS receiver has found a new home.
Cheers,
Arno
Luna, A54-121
|
By
Arno Luijten
·
#42316
·
|
|
Re: [Amel Yacht Owners] Isotemp Basic with double engine water coils
Thanks to all those who commented on this. I will be going ahead and will let you know how it works out.
Mark Pitt
Sabbatical III, SM #419, Lanzarote, Canary Islands
Thanks to all those who commented on this. I will be going ahead and will let you know how it works out.
Mark Pitt
Sabbatical III, SM #419, Lanzarote, Canary Islands
|
By
Mark Pitt
·
#42315
·
|
|
Re: [Amel Yacht Owners] run away windlass
Hi Bill,
That’s probably a good idea, do you have pics of the installations and the parts/sources you used?
I know there’s been discussion in the past about adding a fuse/breaker/interrupt switch
Hi Bill,
That’s probably a good idea, do you have pics of the installations and the parts/sources you used?
I know there’s been discussion in the past about adding a fuse/breaker/interrupt switch
|
By
karkauai
·
#42314
·
|