On 31/07/2020, at 9:53 AM, Porter McRoberts via groups.io <portermcroberts@...> wrote:

Arthur we have the same occurrences. I corrosion X and slightly change the cutoffs and were good for about 6 months. But I’d like to know a long term solution!

Porter A54-152. IBIS. 

Excuse the errors.  

Sent from my IPhone 

Www.fouribis.net

On Jul 30, 2020, at 5:32 PM, Arthur Sundqvist <arthur@...> wrote:

We have the Idromini Acb Waterpump from Gianneschi. Sometimes it will not stop, the pump continues. We have to stop it manually on the pressure switch....
I have pumped up to 2 bar and cleaned the pressure switch. When the motor or Onan generator starts vibrating the pump works well.
What fault could it be. Is it time to change the pump?
Renovate something?
Kindest regards and FAIR WINDS
Arthur Sundqvist
SM435, VISTA

30 juli 2020 kl. 11:53 skrev Porter McRoberts via groups.io <portermcroberts@...>:

Arthur we have the same occurrences. I corrosion X and slightly change the cutoffs and were good for about 6 months. But I’d like to know a long term solution!

Porter A54-152. IBIS. 

Excuse the errors.  

Sent from my IPhone 

Www.fouribis.net

On Jul 30, 2020, at 5:32 PM, Arthur Sundqvist <arthur@...> wrote:corrosion

We have the Idromini Acb Waterpump from Gianneschi. Sometimes it will not stop, the pump continues. We have to stop it manually on the pressure switch....
I have pumped up to 2 bar and cleaned the pressure switch. When the motor or Onan generator starts vibrating the pump works well.
What fault could it be. Is it time to change the pump?
Renovate something?
Kindest regards and FAIR WINDS
Arthur Sundqvist
SM435, VISTA

On Jul 30, 2020, at 5:32 PM, Arthur Sundqvist <arthur@...> wrote:

We have the Idromini Acb Waterpump from Gianneschi. Sometimes it will not stop, the pump continues. We have to stop it manually on the pressure switch....
I have pumped up to 2 bar and cleaned the pressure switch. When the motor or Onan generator starts vibrating the pump works well.
What fault could it be. Is it time to change the pump?
Renovate something?
Kindest regards and FAIR WINDS
Arthur Sundqvist
SM435, VISTA

On 30 Jul 2020, at 04:38, Alan Leslie <s.v.elyse@...> wrote:



[Edited Message Follows]

Hi Tom and Kirstin,

I'm not on my boat so can't be sure, but is it the fuel return line from the injectors on each engine?

That was good fortune to dodge the hurricane !

Cheers

Alan
Elyse SM437

On July 29, 2020 at 8:55 PM eric freedman <kimberlite@...> wrote:

Hi Craig,
I will be happy to order the rail insert once i can confirm it is the one that is on Kimberlite.
I only need a very small piece. One foot would be fine.
My email is Kimberlite@...
Fair Winds
Eric
sm 376

On July 29, 2020 at 6:23 PM "Craig & Katherine Briggs via groups.io" <sangaris@...> wrote:

Hi Eric,
Not to step on a reply from Pat, but today I visited the company, Techno Rubber to go over "our" order. I took my entire starboard side insert and they had Pat's sample. While there, we had a conference call with Pat with the sample inserts sitting in the office so we could discuss them. They have their extrusion dies made by an outside supplier, which is being done now, based on the sample Pat sent them. (These are not pre-defined "models" but custom machined steel dies.)  The die should be back next week and they will run off a few feet, sending some to Pat and I'll pick one up, too (I am close to the shop). After Pat and I check them for any needed fine tuning, we'll give the OK for full length runs.

I was very favorably impressed - this is a small but substantial and very credible family owned operation with three extrusion lines of about 100' each making all sorts of similar extruded products.

There is no question of having the "correct model" - as noted it is custom (no "model #") and Pat and I will check it out. Of course, we can send you a foot or so. If you can commit it would be great so we can share the die cost.  Let us know, please.

ANY OTHER SM OR SN OWNERS WANTING TO REPLACE THEIR (scuzzy, UV damaged, oxidized and ugly) RUB RAIL INSERTS - NOW'S THE TIME!  Let Pat (or me) know, please.

The new ones will be white, (not the original Amel baby diaper brown) - the same as the standard extruded rub rails on pilings and docks that you see everywhere.

Cheers, Craig 
SN68 Sangaris, Tropic Isle Harbor, FL

 

On July 29, 2020 at 7:13 PM "Patrick McAneny via groups.io" <sailw32@...> wrote:

Eric, I can’t add much to Craig’s reply, Craig and I will both trail fit a sample on our boats,to confirm the fit. The die is being made directly from a cross section that we cut from our rub rail insert.If you or any owner would like to join the group buy, please contact me so that I can add you to the list. I expect to place the order in roughly ten days.

Thanks,
Pat
SM Shenanigans

On July 29, 2020 at 6:23 PM "Craig & Katherine Briggs via groups.io" <sangaris@...> wrote:

Hi Eric,
Not to step on a reply from Pat, but today I visited the company, Techno Rubber to go over "our" order. I took my entire starboard side insert and they had Pat's sample. While there, we had a conference call with Pat with the sample inserts sitting in the office so we could discuss them. They have their extrusion dies made by an outside supplier, which is being done now, based on the sample Pat sent them. (These are not pre-defined "models" but custom machined steel dies.)  The die should be back next week and they will run off a few feet, sending some to Pat and I'll pick one up, too (I am close to the shop). After Pat and I check them for any needed fine tuning, we'll give the OK for full length runs.

I was very favorably impressed - this is a small but substantial and very credible family owned operation with three extrusion lines of about 100' each making all sorts of similar extruded products.

There is no question of having the "correct model" - as noted it is custom (no "model #") and Pat and I will check it out. Of course, we can send you a foot or so. If you can commit it would be great so we can share the die cost.  Let us know, please.

ANY OTHER SM OR SN OWNERS WANTING TO REPLACE THEIR (scuzzy, UV damaged, oxidized and ugly) RUB RAIL INSERTS - NOW'S THE TIME!  Let Pat (or me) know, please.

The new ones will be white, (not the original Amel baby diaper brown) - the same as the standard extruded rub rails on pilings and docks that you see everywhere.

Cheers, Craig 
SN68 Sangaris, Tropic Isle Harbor, FL

On July 29, 2020 at 6:23 PM "Craig & Katherine Briggs via groups.io" <sangaris@...> wrote:

Hi Eric,
Not to step on a reply from Pat, but today I visited the company, Techno Rubber to go over "our" order. I took my entire starboard side insert and they had Pat's sample. While there, we had a conference call with Pat with the sample inserts sitting in the office so we could discuss them. They have their extrusion dies made by an outside supplier, which is being done now, based on the sample Pat sent them. (These are not pre-defined "models" but custom machined steel dies.)  The die should be back next week and they will run off a few feet, sending some to Pat and I'll pick one up, too (I am close to the shop). After Pat and I check them for any needed fine tuning, we'll give the OK for full length runs.

I was very favorably impressed - this is a small but substantial and very credible family owned operation with three extrusion lines of about 100' each making all sorts of similar extruded products.

There is no question of having the "correct model" - as noted it is custom (no "model #") and Pat and I will check it out. Of course, we can send you a foot or so. If you can commit it would be great so we can share the die cost.  Let us know, please.

ANY OTHER SM OR SN OWNERS WANTING TO REPLACE THEIR (scuzzy, UV damaged, oxidized and ugly) RUB RAIL INSERTS - NOW'S THE TIME!  Let Pat (or me) know, please.

The new ones will be white, (not the original Amel baby diaper brown) - the same as the standard extruded rub rails on pilings and docks that you see everywhere.

Cheers, Craig 
SN68 Sangaris, Tropic Isle Harbor, FL