Date   

Re: Compass Replacement

Matt Salatino
 

We were able to service ours. (A YouTube exists for this)
Easy.
Remove the top cover. (The plastic buttons on the side act as the hinge for the cover and carefully snap out. If you lose one, Plastimo supplies these as spares, sometimes for free.)
Remove the compass from its mount. You don’t have to remove completely, just to tilt it forward a bit. Prop it so it stays upright. Light wiring didn’t need disconnecting.
The dome is plastic.
Drill a small hole at the top, still under where the cover is located. Make sure the hole is at the top center of the bubble (the reason for tilting the compass forward, to position the top of the bubble under the cover location). We carefully used a home made funnel to fill the air bubble with mineral oil. When full, clean the outside of the sphere very well.
We used clear  5 minute epoxy, a small dab, to cover the hole. Let it set up a bit, so it’s quite thick (so it doesn’t run into the hole). Let dry and reassemble. Bubble gone!
We sold the boat two years later. We keep up with the new owner and the bubble has not reappeared, another two years later.

~~~⛵️~~~Matt

On Jan 18, 2021, at 12:56 PM, Matt & Michelle Day <charlesmatthewday@...> wrote:

After 20+ years of service, the compass on Talia (SM#209) has developed an air bubble (astonishing service life by today's standards).  The compass is a Plastimo Olympic 135. 

My intention was to remove the compass, replace the oil, and/or diaphragm.  However, after disassembly followed by a little web research it appears this model compass is not serviceable.

Anyone on the forum serviced or replaced this compass?  Replaced with the same Olympic 135, or other make/model?

Many thanks for your input.


Re: Compass Replacement

Slavko Despotovic
 

Hello,

Same happened on my previous boat few years ago. I just replaced it with new one. Cost was close to 200 Euro. It was easy, 1 hour work.  The old one I kept for emergency.
--
Slavko
SM 2000
#279 Bonne Anse in Portoroz


Re: Replacing carpet

Patrick McAneny
 

Mike, I considered binding absolutely necessary as we had berber carpet ,that wears very well ,but can unravel if not bound. I would think you would want to bound most carpet for the same reason and of course for appearance sake. As to traction, it has never shifted underfoot , probably because it fits tightly around the perimeter .We chose a short pile as it does not hide and hold sand etc. and can be easily vacuumed .
Pat
SM Shenanigans


-----Original Message-----
From: Mike Ondra via groups.io <mdondra@...>
To: main@AmelYachtOwners.groups.io
Sent: Mon, Jan 18, 2021 11:53 am
Subject: Re: [AmelYachtOwners] Replacing carpet

With the frustration of not finding a urethane foam backed broadloom carpet (apparently available in Canada, but not the US) I am considering a thick carpet without backing. My concern was about traction on the sole but if the carpet is heavy and penned in around the perimeter, slippage may not be an issue. And removing the attached pad constraint opens a world of options. Did you consider not binding the perimeter?
Thanks Pat and all.
Mike
 
From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Patrick McAneny via groups.io
Sent: Monday, January 18, 2021 11:12 AM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Replacing carpet
 
Mike, Diane and I replaced our carpet about ten years ago,we went up the Airbase carpet mart in New Castle ,bought a short nap berber in beige ,used the old carpets as templates ,cut the new carpet maybe a 1/4" shorter all around ,allowing room for the binding of the edges. After cutting the pieces out we took them back and had them bind the edges. The new carpets fit as tight and as exacting as the original. We do not have foam backing ,I like the firm footing while underway ,if I had foam ,I would not want it very thick ,as it would not aid my balance on a rolling floor. The carpet still looks like new ,berber wears very well.
Our boat is in Haven Harbor north ,stopped by Haven Harbor south a few weeks ago ,but did not see your boat.
Stay Safe,
Pat
SM Shenanigans

-----Original Message-----
From: Mike Ondra via groups.io <mdondra@...>
To: main@AmelYachtOwners.groups.io
Sent: Mon, Jan 18, 2021 10:28 am
Subject: [AmelYachtOwners] Replacing carpet
We are looking to replace our carpet and prefer to have a foam back both for comfort and non-slip. Saw Mark’s post on Shaw Nuwave backed carpet but it appears that is no longer in production. Received samples from Boatcarpet.com and even their “Premium Textured 22 oz.” carpet which are not foam backed and seems of low quality. Kanga, in Georgia (USA), makes a polyurethane foam rubber backing which they say they attach to carpet by Shaw, Marquis, Mohawk, and Engineered Floors. So far I have not found any vendor in the US that has such a product. Will continue search, but has anyone recently found a replacement carpet recently that they like?
Mike Ondra
Aletes SM#240
Rock Hall, MD


Re: Replacing carpet

Mark Erdos
 

Found it. The website I got a quote from is gone. Here is the brand: Aquamat. If you do a search for the brand, you can find retailers.

 

No photo description available.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff

www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mark Erdos via groups.io
Sent: Monday, January 18, 2021 7:51 AM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Replacing carpet

 

Hi Mike,

 

Sorry that didn’t work out. Thanks for letting me know it is no longer available. Too bad, carpet has lasted well for us and still looks good.

 

When I replace ours, I did consider another option. It was a plastic ribbed backing. Very high quality but a lot more money. The site I looked at made everything (binding, leather pull up tabs, etc.) and shipped pre-cut and ready to lay down. I’ll see if I can find it.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Tahiti, French Polynesia

www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mike Ondra via groups.io
Sent: Monday, January 18, 2021 5:28 AM
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Replacing carpet

 

We are looking to replace our carpet and prefer to have a foam back both for comfort and non-slip. Saw Mark’s post on Shaw Nuwave backed carpet but it appears that is no longer in production. Received samples from Boatcarpet.com and even their “Premium Textured 22 oz.” carpet which are not foam backed and seems of low quality. Kanga, in Georgia (USA), makes a polyurethane foam rubber backing which they say they attach to carpet by Shaw, Marquis, Mohawk, and Engineered Floors. So far I have not found any vendor in the US that has such a product. Will continue search, but has anyone recently found a replacement carpet recently that they like?

Mike Ondra

Aletes SM#240

Rock Hall, MD


Compass Replacement

Matt & Michelle Day, SM#208 SV Talia
 

After 20+ years of service, the compass on Talia (SM#209) has developed an air bubble (astonishing service life by today's standards).  The compass is a Plastimo Olympic 135. 

My intention was to remove the compass, replace the oil, and/or diaphragm.  However, after disassembly followed by a little web research it appears this model compass is not serviceable.

Anyone on the forum serviced or replaced this compass?  Replaced with the same Olympic 135, or other make/model?

Many thanks for your input.


Re: Replacing carpet

Mark Erdos
 

Hi Mike,

 

Sorry that didn’t work out. Thanks for letting me know it is no longer available. Too bad, carpet has lasted well for us and still looks good.

 

When I replace ours, I did consider another option. It was a plastic ribbed backing. Very high quality but a lot more money. The site I looked at made everything (binding, leather pull up tabs, etc.) and shipped pre-cut and ready to lay down. I’ll see if I can find it.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Tahiti, French Polynesia

www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of Mike Ondra via groups.io
Sent: Monday, January 18, 2021 5:28 AM
To: main@AmelYachtOwners.groups.io
Subject: [AmelYachtOwners] Replacing carpet

 

We are looking to replace our carpet and prefer to have a foam back both for comfort and non-slip. Saw Mark’s post on Shaw Nuwave backed carpet but it appears that is no longer in production. Received samples from Boatcarpet.com and even their “Premium Textured 22 oz.” carpet which are not foam backed and seems of low quality. Kanga, in Georgia (USA), makes a polyurethane foam rubber backing which they say they attach to carpet by Shaw, Marquis, Mohawk, and Engineered Floors. So far I have not found any vendor in the US that has such a product. Will continue search, but has anyone recently found a replacement carpet recently that they like?

Mike Ondra

Aletes SM#240

Rock Hall, MD


Re: Replacing carpet

Mike Ondra
 

With the frustration of not finding a urethane foam backed broadloom carpet (apparently available in Canada, but not the US) I am considering a thick carpet without backing. My concern was about traction on the sole but if the carpet is heavy and penned in around the perimeter, slippage may not be an issue. And removing the attached pad constraint opens a world of options. Did you consider not binding the perimeter?

Thanks Pat and all.

Mike

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of Patrick McAneny via groups.io
Sent: Monday, January 18, 2021 11:12 AM
To: main@AmelYachtOwners.groups.io
Subject: Re: [AmelYachtOwners] Replacing carpet

 

Mike, Diane and I replaced our carpet about ten years ago,we went up the Airbase carpet mart in New Castle ,bought a short nap berber in beige ,used the old carpets as templates ,cut the new carpet maybe a 1/4" shorter all around ,allowing room for the binding of the edges. After cutting the pieces out we took them back and had them bind the edges. The new carpets fit as tight and as exacting as the original. We do not have foam backing ,I like the firm footing while underway ,if I had foam ,I would not want it very thick ,as it would not aid my balance on a rolling floor. The carpet still looks like new ,berber wears very well.

Our boat is in Haven Harbor north ,stopped by Haven Harbor south a few weeks ago ,but did not see your boat.

Stay Safe,

Pat

SM Shenanigans

-----Original Message-----
From: Mike Ondra via groups.io <mdondra@...>
To: main@AmelYachtOwners.groups.io
Sent: Mon, Jan 18, 2021 10:28 am
Subject: [AmelYachtOwners] Replacing carpet

We are looking to replace our carpet and prefer to have a foam back both for comfort and non-slip. Saw Mark’s post on Shaw Nuwave backed carpet but it appears that is no longer in production. Received samples from Boatcarpet.com and even their “Premium Textured 22 oz.” carpet which are not foam backed and seems of low quality. Kanga, in Georgia (USA), makes a polyurethane foam rubber backing which they say they attach to carpet by Shaw, Marquis, Mohawk, and Engineered Floors. So far I have not found any vendor in the US that has such a product. Will continue search, but has anyone recently found a replacement carpet recently that they like?

Mike Ondra

Aletes SM#240

Rock Hall, MD


Re: Replacing carpet

Patrick McAneny
 

Mike, Diane and I replaced our carpet about ten years ago,we went up the Airbase carpet mart in New Castle ,bought a short nap berber in beige ,used the old carpets as templates ,cut the new carpet maybe a 1/4" shorter all around ,allowing room for the binding of the edges. After cutting the pieces out we took them back and had them bind the edges. The new carpets fit as tight and as exacting as the original. We do not have foam backing ,I like the firm footing while underway ,if I had foam ,I would not want it very thick ,as it would not aid my balance on a rolling floor. The carpet still looks like new ,berber wears very well.
Our boat is in Haven Harbor north ,stopped by Haven Harbor south a few weeks ago ,but did not see your boat.
Stay Safe,
Pat
SM Shenanigans


-----Original Message-----
From: Mike Ondra via groups.io <mdondra@...>
To: main@AmelYachtOwners.groups.io
Sent: Mon, Jan 18, 2021 10:28 am
Subject: [AmelYachtOwners] Replacing carpet

We are looking to replace our carpet and prefer to have a foam back both for comfort and non-slip. Saw Mark’s post on Shaw Nuwave backed carpet but it appears that is no longer in production. Received samples from Boatcarpet.com and even their “Premium Textured 22 oz.” carpet which are not foam backed and seems of low quality. Kanga, in Georgia (USA), makes a polyurethane foam rubber backing which they say they attach to carpet by Shaw, Marquis, Mohawk, and Engineered Floors. So far I have not found any vendor in the US that has such a product. Will continue search, but has anyone recently found a replacement carpet recently that they like?
Mike Ondra
Aletes SM#240
Rock Hall, MD


Re: Fresh Water Pump

Stephen Davis
 

I agree with Bill regarding the Marco pump. We have had one for several years now, and consider it to be much higher quality than most of the other pumps available. 

Steve Davis
Aloha SM 72
Port Townsend, WA


Re: Replacing carpet

Bill Hall
 

Have you considered roll neoprene.  It comes in different colors and thicknesses.  Supplier should be easy to track down.  Think wet suites

On Mon, Jan 18, 2021 at 7:34 AM Aras Grinius <aras.grinius@...> wrote:
One thought would those bathroom carpets. If you could figure out the manufacturer then maybe you could a larger size / custom cut.   Those carpet are meant for wet environs.  Just a thought.
I use them in my salon [course my space is much smaller.

Aras Sharki #163 1988

On Mon, Jan 18, 2021 at 10:28 AM Mike Ondra via groups.io <mdondra=verizon.net@groups.io> wrote:

We are looking to replace our carpet and prefer to have a foam back both for comfort and non-slip. Saw Mark’s post on Shaw Nuwave backed carpet but it appears that is no longer in production. Received samples from Boatcarpet.com and even their “Premium Textured 22 oz.” carpet which are not foam backed and seems of low quality. Kanga, in Georgia (USA), makes a polyurethane foam rubber backing which they say they attach to carpet by Shaw, Marquis, Mohawk, and Engineered Floors. So far I have not found any vendor in the US that has such a product. Will continue search, but has anyone recently found a replacement carpet recently that they like?

Mike Ondra

Aletes SM#240

Rock Hall, MD













--
Aras Grinius











Re: Replacing carpet

Aras Grinius
 

One thought would those bathroom carpets. If you could figure out the manufacturer then maybe you could a larger size / custom cut.   Those carpet are meant for wet environs.  Just a thought.
I use them in my salon [course my space is much smaller.

Aras Sharki #163 1988


On Mon, Jan 18, 2021 at 10:28 AM Mike Ondra via groups.io <mdondra=verizon.net@groups.io> wrote:

We are looking to replace our carpet and prefer to have a foam back both for comfort and non-slip. Saw Mark’s post on Shaw Nuwave backed carpet but it appears that is no longer in production. Received samples from Boatcarpet.com and even their “Premium Textured 22 oz.” carpet which are not foam backed and seems of low quality. Kanga, in Georgia (USA), makes a polyurethane foam rubber backing which they say they attach to carpet by Shaw, Marquis, Mohawk, and Engineered Floors. So far I have not found any vendor in the US that has such a product. Will continue search, but has anyone recently found a replacement carpet recently that they like?

Mike Ondra

Aletes SM#240

Rock Hall, MD



--
Aras Grinius


Replacing carpet

Mike Ondra
 

We are looking to replace our carpet and prefer to have a foam back both for comfort and non-slip. Saw Mark’s post on Shaw Nuwave backed carpet but it appears that is no longer in production. Received samples from Boatcarpet.com and even their “Premium Textured 22 oz.” carpet which are not foam backed and seems of low quality. Kanga, in Georgia (USA), makes a polyurethane foam rubber backing which they say they attach to carpet by Shaw, Marquis, Mohawk, and Engineered Floors. So far I have not found any vendor in the US that has such a product. Will continue search, but has anyone recently found a replacement carpet recently that they like?

Mike Ondra

Aletes SM#240

Rock Hall, MD


Re: Zoom meeting with Olivier Beaute

Joerg Esdorn
 

Billy, I asked exactly that question of Amel and they told me that there is no impact for the 55.  Cheers Joerg

Joerg Esdorn
A55 #37 Kincsem
On the hard in Vigo, Spain
 


Re: Fresh Water Pump

Martin Birkhoff
 

Hi Ian,
in July 2018 we replaced the failing fresh water pump to a Marco UP6 25 PSI. Since then it is working without any problems and there is sufficient pressure on all tabs and outlets (dish washer, washing machine, showers including the stern shower).

Martin Birkhoff

Mago del Sur - 54#40


Re: Fresh Water Pump

Karen Smith
 

I know it violates your stated desire for a diaphragm pump, but I think the Marco gear pumps are the cat's meow.  I think you'd be happy with a #3 or a #6.

They are simple, robust, quiet, and very compact with continuously variable speed so supply pressure is constant.  We have had one for almost 5 years, and haven't needed to work on it yet.  A spare parts kit of a shaft seal, motor brushes, and a few gears and they should go almost forever.

I personally would not go to a 55 PSI pump.  That is just an invitation to waste water.  We are very happy with a steady 25PSI.  

Bill Kinney
SM160, Harmonie
Charleston, SC, USA


Re: Fresh Water Pump

Thomas Kleman
 

We have the aqua king 2 and love it. Good pressure with both showers going. Very reliable in that we've been full time live-aboards for 10 years and I've replaced it once.......with a spare I seemed to acquire in 2012.

Tom and Kirstin
SM2K 422


Re: Bilge pump activation switch

 

CorrosionX is a sailor's best friend! I could tell you dozens of similar stories. If you own an Amel and do not have one of these, you will spend a lot more money than those who do have one of these:
image.png

CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Sun, Jan 17, 2021 at 2:21 PM rossirossix4 <rossidesigngroup@...> wrote:

A related recommendation (may be helpful to others in future searches).  Our bilge pump activation switch began to fail, staying on even after the cord pulled the switch down and into the off position.  This was gradual, at first fixed by simply cycling the switch but finally just staying on.  I ordered a replacement assembly from Amel. In the meantime as a stopgap measure I shot Corrosion-X into the switch (after removing the sump tube and switch so I could work with it on the dock holding it in different positions).  I collected a great deal of black residue in paper towels and continued sprays until I had no residue.  Replacement switch came a week later but switch was working just fine.  It has now been about 5 years.  I squirt Corrosion-X into the switch periodically, including the contacts. I would encourage anyone cleaning the tube to conduct the same procedure until the residue is clear.

Bob KAIMI SM2K 429 

Vice-President, Corrosion-X Consumer Advisory Council of North America
Director, Amel Institute of Low Technology


Re: Bilge pump activation switch

rossirossix4
 
Edited

A related recommendation (may be helpful to others in future searches).  Our bilge pump activation switch began to fail, staying on even after the cord pulled the switch down and into the off position.  This was gradual, at first fixed by simply cycling the switch but finally just staying on.  I ordered a replacement assembly from Amel. In the meantime as a stopgap measure I shot Corrosion-X into the switch (after removing the sump tube and switch so I could work with it on the dock holding it in different positions).  I collected a great deal of black residue in paper towels and continued sprays until I had no residue.  Replacement switch came a week later but switch was working just fine so we just kept the new part as a spare.  It has now been about 5 years.  I squirt Corrosion-X into the switch periodically, including the contacts. I would encourage anyone cleaning the tube to conduct the same procedure until the residue is clear.

Bob KAIMI SM2K 429 

Vice-President, Corrosion-X Consumer Advisory Council of North America
Director, Amel Institute of Low Technology


Re: Main outhaul travller

Danny and Yvonne SIMMS
 

Hi Nick, if I understand you correctly the cracked part is the curved piece that carries the balls around the end. I had the same and the replacement car was expensive so almost for the fun of trying I made a replacement from aluminium plate. Tools. Hacksaw, bench grinder, vice and rat tail (round) file, half moon file. And of course a drill. Successful but I would have hated to pay myself for the hours it took. Good result and a long term fix. Reloading the car onto the track requires a short section of track to pre load the balls. Then butt this up to the track and feed it on. I couldnt source a short piece of track easily so I formed one out of wood. Some of the little balls were damaged so I replaced them all

Regards

Danny

SM 299

Ocean Pearl



On 17 January 2021 at 10:18 "Nick Fowle SM 404 Rascal via groups.io" <svrascal@...> wrote:

Hi, I have a broken shackle on the main outhaul car . The bar across the middle of the shackle is broken. When taking it apart today I noticed that there was a crack on one of the end pieces, close to the philips screw, which seems to be more than just cosmetic.

Anyone know whether its possible to replace a) the shackle and b) this small grey "end piece"

I have had a look on the Antel website to see if I could find a part numbers but looking at ANTAL's website http://www.antal.it/eng/4110SH_en , using the correct part number, which  I believe to be Model #4110/SH, the car looks very different from the one on my boom, so I guess it has been updated. If this is the case, any ideas where I can try and source these small parts, I have tried Defender, ebay and a few other searches but to no avail. 

thanks


Re: Main outhaul travller

Danny and Yvonne SIMMS
 

Hi Nick. If I understand you correctlt th

On 17 January 2021 at 10:18 "Nick Fowle SM 404 Rascal via groups.io" <svrascal@...> wrote:

Hi, I have a broken shackle on the main outhaul car . The bar across the middle of the shackle is broken. When taking it apart today I noticed that there was a crack on one of the end pieces, close to the philips screw, which seems to be more than just cosmetic.

Anyone know whether its possible to replace a) the shackle and b) this small grey "end piece"

I have had a look on the Antel website to see if I could find a part numbers but looking at ANTAL's website http://www.antal.it/eng/4110SH_en , using the correct part number, which  I believe to be Model #4110/SH, the car looks very different from the one on my boom, so I guess it has been updated. If this is the case, any ideas where I can try and source these small parts, I have tried Defender, ebay and a few other searches but to no avail. 

thanks

3141 - 3160 of 59217