Date   

Re: Excessive usage of water maker membranes

Danny and Yvonne SIMMS
 

We make water while motor sailing. No problems and we have the Amel single through hull for salt water intake. We never use chemicals for sterilising or pickling. Just back flush with NON chorinated water from the tank with the pressure valve totally released after each use.

Kind Regards

Danny

SM 299

Ocean Pearl

Kind Regards

DANNY

SM 299

OCEAN PEARL

On 19 April 2020 at 18:38 Ken Powers SV Aquarius <ken@...> wrote:

Hello Mark,

On Aquarius, we also have this problem with our 24V D60.  We continually see an increase in the ppm each year.  I have a few questions so we might flush this out...

1) Do you have a pre-pump that feeds your high pressure pump?
2) For those that have a pre-pump, do you see this problem?

I am starting to get the feeling that cavitation do to air in the system is causing the problem on Aquarius.  We only have a single sea water intake, stock Amel, and we do make water while motor sailing, and this could cause air to get into the water-maker system.  With the air in the system I am led to believe this is like a jack hammer on the membranes causing micro tears to form.  Overtime, the holes get bigger, and whaalaa 1000 ppm.

I don't have the pre-pump on Aquarius, but I am planing to add the pump when I install new membranes in about 6 months. 

Does anyone have any thoughts about this?

Ken
Aboard Aquarius Locked Down in Phuket
SM2K#262


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Nick Fowle
 

Hi Bill,

If the Time Zome works for me (Singaoire) I would be interested . 

Regds



On Sun, 19 Apr 2020 at 1:46 PM, Meadow Marmar via groups.io <mnimitz=aol.com@groups.io> wrote:

Hi Bill,

Rick and I would love to be included as well! 


Warm regards,

Meadow
S/V Althea SM317


Re: Excessive usage of water maker membranes

Ken Powers SV Aquarius
 

Hello Mark,

On Aquarius, we also have this problem with our 24V D60.  We continually see an increase in the ppm each year.  I have a few questions so we might flush this out...

1) Do you have a pre-pump that feeds your high pressure pump?
2) For those that have a pre-pump, do you see this problem?

I am starting to get the feeling that cavitation do to air in the system is causing the problem on Aquarius.  We only have a single sea water intake, stock Amel, and we do make water while motor sailing, and this could cause air to get into the water-maker system.  With the air in the system I am led to believe this is like a jack hammer on the membranes causing micro tears to form.  Overtime, the holes get bigger, and whaalaa 1000 ppm.

I don't have the pre-pump on Aquarius, but I am planing to add the pump when I install new membranes in about 6 months. 

Does anyone have any thoughts about this?

Ken
Aboard Aquarius Locked Down in Phuket
SM2K#262


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Meadow Marmar
 

Hi Bill,

Rick and I would love to be included as well! 


Warm regards,

Meadow
S/V Althea SM317


Re: Excessive usage of water maker membranes

Alan Leslie
 

Something seriously amiss here.
The previous owner replaced the membranes in 2013 just before we bought Elyse.
The system has been running fine ever since. We have an inline TDS monitor and the TDS is still after 7 years less than 300...depending on temperature it can be as low as 150.
We never run the watermaker in the marina, but have a timer and solenoid system that flushes the system with tank water every two days when the boat is left in the marina as it is now, unfortunately.
We never put shore water in the tanks, only RO water .
One thing is that when flushing with fresh water the outlet valve should be all the way open i.e. no pressure across the membrane, and when starting up to make fresh water, the system should be flushed with saltwater for a few minutes to flush out all the fresh water before increasing the pressure to make water. I believe that having high pressure across these membranes with fresh water can ruin them.
Cheers
Alan
Elyse SM437 


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Davi Rozgonyi
 

Hey all, would definitely hang out and listen and learn if the time difference works out. Locked down in Corfu... 
Davi
SM56 Wake


Re: Excessive usage of water maker membranes

Mark Erdos
 

Hi Colin,

 

Yes, I re-read that part and it is a little confusing how I wrote it. In marina, we do a fresh water flush aobut once a week. We do not run the water maker in that environment.

 

Thanks for the insight, I guess I need to be more fussy about where we run it. I thought the pre-filter would help a lot. I guess not.

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff

www.creampuff.us

 

From: main@AmelYachtOwners.groups.io [mailto:main@AmelYachtOwners.groups.io] On Behalf Of islandpearl2_sm2k332
Sent: Saturday, April 18, 2020 10:47 PM
To: main@amelyachtowners.groups.io
Subject: Re: [AmelYachtOwners] Excessive usage of water maker membranes

 

Hi Mark

 

We had the 100L/Hr Duo on Island Pearl II and went around the work in three years with a new 2016 set of membranes. Those membranes were still perfect at the end of our trip doing a full 100L/Hr easily on the a/c current but slightly down to 75L/hr on the DC current motor. 

 

We were absolutely fussy about the cleanliness of ocean water before running it and were sometimes scoffed at by others eg in Rodrigues (Indian Ocean) for lifting anchor, risking losing our good spot to go out to sea every four-five days to make water whilst other cruiser friends simply made water inside the large seawater harbour where we felt the water was not up to scratch. Also, we never took the boat out onto the hard for a season, even though we had planned to do this in the Caribbean in 2019.

 

If you are careful like this, which I suspect you are, then there must be something else at play with your system and I look forward to hearing about that from other more experienced cruisers here.

 

Also, since we have communicated often and I admire your equally careful approach to looking after Creampuff, I highly suspect that when you refer to "running your watermaker at least once per week in marina's", that you actually meant "doing a freshwater flush cycle" in the marina from your tank as per the manual requirements.... rather than actually making water from the extremely dirty marina seawater which would totally explain everything about your problems, but which I am equally sure you would never have done. 

 

Colin Streeter

Brisbane ex Island Pearl II

 

On Sun, Apr 19, 2020 at 12:10 PM Danny and Yvonne SIMMS <simms@...> wrote:

Hi Mark.

I am very careful about where i run my watermaker. Never in a marina and it has to be an exeptionaly clean harbour before I will run it there. Also I am paranoid about even traces of chlorine. It is many years since I allowed any chlorinated water into my tank. However you living full time aboard would suggest a lot of use. Like a car,  its not the time that wears them out but the milage. 

Regards

Danny

SM 299

Ocean Pearl

On 19 April 2020 at 12:21 Mark Erdos <mcerdos@...> wrote:

I need a little help with water maker usage and maintenance, please.

 

Cream Puff has a 24v D60 water-maker. My problem is we seem to be going through membranes at the rate of a pair a year. I have read where others have used the same set of membranes for years and still get drinkable water. This is not the case with us. We are in our 5th year of full time cruising and are now on our 6th set of membranes.

 

When I last change membranes in Colombia, this was about March 2019. Our current membranes are just over a year old. The PPMs are starting to creep up a bit now and we have gone from the 300 range to the 500 range. We notice a change in drinking quality over 600 PPMs. This is when we usually change the membranes.

 

We run the water-maker at least once a week when in a marina, flush it with the fresh water rinse. I have a double charcoal filter set up for the tank rinse. When on anchor it is run just about every day. I am careful to watch the pressure and water making float gauge. I normally set it at 55 liters per hour and this put the pressure in lower side of the green range.

 

Any ideas why our membranes are not lasting or why our PPMs creep up?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Tahiti, French Polynesia

www.creampuff.us

 


 


 


 

--

Colin Streeter

0411 016 445


Re: Excessive usage of water maker membranes

Colin - ex SV Island Pearl
 

Hi Mark

We had the 100L/Hr Duo on Island Pearl II and went around the work in three years with a new 2016 set of membranes. Those membranes were still perfect at the end of our trip doing a full 100L/Hr easily on the a/c current but slightly down to 75L/hr on the DC current motor. 

We were absolutely fussy about the cleanliness of ocean water before running it and were sometimes scoffed at by others eg in Rodrigues (Indian Ocean) for lifting anchor, risking losing our good spot to go out to sea every four-five days to make water whilst other cruiser friends simply made water inside the large seawater harbour where we felt the water was not up to scratch. Also, we never took the boat out onto the hard for a season, even though we had planned to do this in the Caribbean in 2019.

If you are careful like this, which I suspect you are, then there must be something else at play with your system and I look forward to hearing about that from other more experienced cruisers here.

Also, since we have communicated often and I admire your equally careful approach to looking after Creampuff, I highly suspect that when you refer to "running your watermaker at least once per week in marina's", that you actually meant "doing a freshwater flush cycle" in the marina from your tank as per the manual requirements.... rather than actually making water from the extremely dirty marina seawater which would totally explain everything about your problems, but which I am equally sure you would never have done. 

Colin Streeter
Brisbane ex Island Pearl II

On Sun, Apr 19, 2020 at 12:10 PM Danny and Yvonne SIMMS <simms@...> wrote:

Hi Mark.

I am very careful about where i run my watermaker. Never in a marina and it has to be an exeptionaly clean harbour before I will run it there. Also I am paranoid about even traces of chlorine. It is many years since I allowed any chlorinated water into my tank. However you living full time aboard would suggest a lot of use. Like a car,  its not the time that wears them out but the milage. 

Regards

Danny

SM 299

Ocean Pearl

On 19 April 2020 at 12:21 Mark Erdos <mcerdos@...> wrote:

I need a little help with water maker usage and maintenance, please.

 

Cream Puff has a 24v D60 water-maker. My problem is we seem to be going through membranes at the rate of a pair a year. I have read where others have used the same set of membranes for years and still get drinkable water. This is not the case with us. We are in our 5th year of full time cruising and are now on our 6th set of membranes.

 

When I last change membranes in Colombia, this was about March 2019. Our current membranes are just over a year old. The PPMs are starting to creep up a bit now and we have gone from the 300 range to the 500 range. We notice a change in drinking quality over 600 PPMs. This is when we usually change the membranes.

 

We run the water-maker at least once a week when in a marina, flush it with the fresh water rinse. I have a double charcoal filter set up for the tank rinse. When on anchor it is run just about every day. I am careful to watch the pressure and water making float gauge. I normally set it at 55 liters per hour and this put the pressure in lower side of the green range.

 

Any ideas why our membranes are not lasting or why our PPMs creep up?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Tahiti, French Polynesia

www.creampuff.us

 


 


 



--
Colin Streeter
0411 016 445


Re: Excessive usage of water maker membranes

Danny and Yvonne SIMMS
 

Hi Mark.

I am very careful about where i run my watermaker. Never in a marina and it has to be an exeptionaly clean harbour before I will run it there. Also I am paranoid about even traces of chlorine. It is many years since I allowed any chlorinated water into my tank. However you living full time aboard would suggest a lot of use. Like a car,  its not the time that wears them out but the milage. 

Regards

Danny

SM 299

Ocean Pearl

On 19 April 2020 at 12:21 Mark Erdos <mcerdos@...> wrote:

I need a little help with water maker usage and maintenance, please.

 

Cream Puff has a 24v D60 water-maker. My problem is we seem to be going through membranes at the rate of a pair a year. I have read where others have used the same set of membranes for years and still get drinkable water. This is not the case with us. We are in our 5th year of full time cruising and are now on our 6th set of membranes.

 

When I last change membranes in Colombia, this was about March 2019. Our current membranes are just over a year old. The PPMs are starting to creep up a bit now and we have gone from the 300 range to the 500 range. We notice a change in drinking quality over 600 PPMs. This is when we usually change the membranes.

 

We run the water-maker at least once a week when in a marina, flush it with the fresh water rinse. I have a double charcoal filter set up for the tank rinse. When on anchor it is run just about every day. I am careful to watch the pressure and water making float gauge. I normally set it at 55 liters per hour and this put the pressure in lower side of the green range.

 

Any ideas why our membranes are not lasting or why our PPMs creep up?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Tahiti, French Polynesia

www.creampuff.us

 


 


 


Re: Excessive usage of water maker membranes

Bill Hall
 

Running your water maker in a marina environment can expose it to oil and fuel residues.  Oils will ruin water maker membrains.   If you don’t have an oil separation filter on your intake it would be worth installing one

On Sat, Apr 18, 2020 at 6:18 PM Mark Erdos <mcerdos@...> wrote:

I need a little help with water maker usage and maintenance, please.

 

Cream Puff has a 24v D60 water-maker. My problem is we seem to be going through membranes at the rate of a pair a year. I have read where others have used the same set of membranes for years and still get drinkable water. This is not the case with us. We are in our 5th year of full time cruising and are now on our 6th set of membranes.

 

When I last change membranes in Colombia, this was about March 2019. Our current membranes are just over a year old. The PPMs are starting to creep up a bit now and we have gone from the 300 range to the 500 range. We notice a change in drinking quality over 600 PPMs. This is when we usually change the membranes.

 

We run the water-maker at least once a week when in a marina, flush it with the fresh water rinse. I have a double charcoal filter set up for the tank rinse. When on anchor it is run just about every day. I am careful to watch the pressure and water making float gauge. I normally set it at 55 liters per hour and this put the pressure in lower side of the green range.

 

Any ideas why our membranes are not lasting or why our PPMs creep up?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Tahiti, French Polynesia

www.creampuff.us

 


Excessive usage of water maker membranes

Mark Erdos
 

I need a little help with water maker usage and maintenance, please.

 

Cream Puff has a 24v D60 water-maker. My problem is we seem to be going through membranes at the rate of a pair a year. I have read where others have used the same set of membranes for years and still get drinkable water. This is not the case with us. We are in our 5th year of full time cruising and are now on our 6th set of membranes.

 

When I last change membranes in Colombia, this was about March 2019. Our current membranes are just over a year old. The PPMs are starting to creep up a bit now and we have gone from the 300 range to the 500 range. We notice a change in drinking quality over 600 PPMs. This is when we usually change the membranes.

 

We run the water-maker at least once a week when in a marina, flush it with the fresh water rinse. I have a double charcoal filter set up for the tank rinse. When on anchor it is run just about every day. I am careful to watch the pressure and water making float gauge. I normally set it at 55 liters per hour and this put the pressure in lower side of the green range.

 

Any ideas why our membranes are not lasting or why our PPMs creep up?

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Tahiti, French Polynesia

www.creampuff.us

 


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Germain Jean-Pierre
 

I’d like to attend also…

Jean-Pierre Germain,  SY Eleuthera SM 007



On 19 Apr 2020, at 09:21, Karen Smith via groups.io <karenharmonie@...> wrote:

I’d like to join also! Let us know the date & time!

Thanks, Karen
S/v Harmonie SM #160






Jean-Pierre Germain




Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Karen Smith
 

I’d like to join also! Let us know the date & time!

Thanks, Karen
S/v Harmonie SM #160




Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Roy Zakheym
 

Hi Bill
I'm interested as well
Best regards
Roy zakheym.



Sent from my Samsung Galaxy smartphone.


-------- Original message --------
From: CW Bill Rouse <brouse@...>
Date: 4/17/20 20:12 (GMT+02:00)
To: "main@AmelYachtOwners.groups.io Notification" <main@amelyachtowners.groups.io>
Subject: [AmelYachtOwners] 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

All,

I received an excellent suggestion from an Amel owner this morning. He suggested a ZOOM meeting for interested owners to discuss a few topics.

I envision us meeting for a total of 30 minutes to discuss two issues. If there is interest we could schedule subsequent ZOOM meetings.

Is there any member of our group that is experienced with hosting a ZOOM meeting and willing to volunteer to moderate the meeting?

Any other thoughts?

Bill
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Teun BAAS
 

Bill,

 

Interested.

 

Best Regards Teun

SV AMELIT  A54  #128

 

Currently on the hard in COOMERA (near BRISBANE) QLD AUSTRALIA

April 18, 2020 10:22:30

 

USA cell: +1 832 477 8842

AUSTRALIA cell: +61 5951 8909

 

You can follow AMELIT via this link: https://forecast.predictwind.com/tracking/display/AMELIT

 

 

From: main@AmelYachtOwners.groups.io <main@AmelYachtOwners.groups.io> On Behalf Of CW Bill Rouse via groups.io
Sent: Saturday, April 18, 2020 07:14
To: main@AmelYachtOwners.groups.io Notification <main@amelyachtowners.groups.io>
Subject: Re: [AmelYachtOwners] 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

 

All,

 

I am going to wait a few more days to be able to get some more comments. I have been contacted by one group member who is an experienced ZOOM administrator and has a commercial account with ZOOM. This will benefit all of us.

 

Those interested please reply to this thread with their suggested topic(s), or any other suggestions. Once I have those suggestions, I will produce a "poll" of suggested date/times and topics.

 

When the above is completed, I plan to turn it over to the volunteer owner/administrator.

 

I am looking forward to this.

 

Bill

CW Bill Rouse Amel Owners Yacht School

Address: 720 Winnie, Galveston Island, Texas 77550 

 

View My Training Calendar

 

 

On Sat, Apr 18, 2020 at 8:26 AM Brian Riggs <7briggs@...> wrote:

As a future SM2k owner, I'd love to lurk as well.

 

Cheers!

Brian Riggs

 

On Sat, Apr 18, 2020, 09:20 Porter McRoberts via groups.io <portermcroberts=yahoo.com@groups.io> wrote:

Love to be a part of this. Regardless of topics.

Porter 

S/v ibis



On Apr 18, 2020, at 9:03 AM, HOFMEYR SCHOLTZ <hoffi@...> wrote:

I there,
I'm a near-future Amel owner. If you'd have me please count me in.
Hofmeyr


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Fabio Palazzo
 

I’d like to listen in as well. 

Fabio Palazzo
Future Maramu owner


On Apr 18, 2020, at 5:59 PM, stevejb59 <stevejb59@...> wrote:

On Sat, Apr 18, 2020 at 09:26 AM, Ian Townsend wrote:
Interested. 
 
 
A couple of SM specific topics:
- furler maintenance
- dodger window replacement 
- galley upgrades eg. Refrigeration, oven/stove, sinks, taps, counters, etc.
 
Topics that might apply to all/most:
- rig tuning
- blue water dinghy storage 
- anchors
 
Ian
SM153
Fort Lauderdale, FL
 
Sent from my Samsung Galaxy smartphone.
 
 
-------- Original message --------
From: CW Bill Rouse <brouse@...>
Date: 2020-04-18 10:14 (GMT-05:00)
Subject: Re: [AmelYachtOwners] 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿
 
All,
 
I am going to wait a few more days to be able to get some more comments. I have been contacted by one group member who is an experienced ZOOM administrator and has a commercial account with ZOOM. This will benefit all of us.
 
Those interested please reply to this thread with their suggested topic(s), or any other suggestions. Once I have those suggestions, I will produce a "poll" of suggested date/times and topics.
 
When the above is completed, I plan to turn it over to the volunteer owner/administrator.
 
I am looking forward to this.
 
Bill
CW Bill Rouse Amel Owners Yacht School
 
Address: 720 Winnie, Galveston Island, Texas 77550 
 
View My Training Calendar

On Sat, Apr 18, 2020 at 8:26 AM Brian Riggs <7briggs@...> wrote:
As a future SM2k owner, I'd love to lurk as well.
 
Cheers!
Brian Riggs

On Sat, Apr 18, 2020, 09:20 Porter McRoberts via groups.io <portermcroberts=yahoo.com@groups.io> wrote:
Love to be a part of this. Regardless of topics.
Porter 
S/v ibis

 

On Apr 18, 2020, at 9:03 AM, HOFMEYR SCHOLTZ <hoffi@...> wrote:

I there,
I'm a near-future Amel owner. If you'd have me please count me in.
Hofmeyr

 

 


 Hi All.
We would also be intrested if timing is suitable.
locked down in Spain.

Regards

Steve Bell
S/Y Dusk
SM #378


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Steve Bell
 

On Sat, Apr 18, 2020 at 09:26 AM, Ian Townsend wrote:
Interested. 
 
 
A couple of SM specific topics:
- furler maintenance
- dodger window replacement 
- galley upgrades eg. Refrigeration, oven/stove, sinks, taps, counters, etc.
 
Topics that might apply to all/most:
- rig tuning
- blue water dinghy storage 
- anchors
 
Ian
SM153
Fort Lauderdale, FL
 
Sent from my Samsung Galaxy smartphone.
 
 
-------- Original message --------
From: CW Bill Rouse <brouse@...>
Date: 2020-04-18 10:14 (GMT-05:00)
To: "main@AmelYachtOwners.groups.io Notification" <main@amelyachtowners.groups.io>
Subject: Re: [AmelYachtOwners] 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿
 
All,
 
I am going to wait a few more days to be able to get some more comments. I have been contacted by one group member who is an experienced ZOOM administrator and has a commercial account with ZOOM. This will benefit all of us.
 
Those interested please reply to this thread with their suggested topic(s), or any other suggestions. Once I have those suggestions, I will produce a "poll" of suggested date/times and topics.
 
When the above is completed, I plan to turn it over to the volunteer owner/administrator.
 
I am looking forward to this.
 
Bill
CW Bill Rouse Amel Owners Yacht School
 
Address: 720 Winnie, Galveston Island, Texas 77550 
 
View My Training Calendar

On Sat, Apr 18, 2020 at 8:26 AM Brian Riggs <7briggs@...> wrote:
As a future SM2k owner, I'd love to lurk as well.
 
Cheers!
Brian Riggs

On Sat, Apr 18, 2020, 09:20 Porter McRoberts via groups.io <portermcroberts=yahoo.com@groups.io> wrote:
Love to be a part of this. Regardless of topics.
Porter 
S/v ibis

 

On Apr 18, 2020, at 9:03 AM, HOFMEYR SCHOLTZ <hoffi@...> wrote:

I there,
I'm a near-future Amel owner. If you'd have me please count me in.
Hofmeyr

 

 


 Hi All.
We would also be intrested if timing is suitable.
locked down in Spain.

Regards

Steve Bell
S/Y Dusk
SM #378


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Ian Townsend
 

Interested. 


A couple of SM specific topics:
- furler maintenance
- dodger window replacement 
- galley upgrades eg. Refrigeration, oven/stove, sinks, taps, counters, etc.

Topics that might apply to all/most:
- rig tuning
- blue water dinghy storage 
- anchors

Ian
SM153
Fort Lauderdale, FL

Sent from my Samsung Galaxy smartphone.


-------- Original message --------
From: CW Bill Rouse <brouse@...>
Date: 2020-04-18 10:14 (GMT-05:00)
To: "main@AmelYachtOwners.groups.io Notification" <main@amelyachtowners.groups.io>
Subject: Re: [AmelYachtOwners] 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

All,

I am going to wait a few more days to be able to get some more comments. I have been contacted by one group member who is an experienced ZOOM administrator and has a commercial account with ZOOM. This will benefit all of us.

Those interested please reply to this thread with their suggested topic(s), or any other suggestions. Once I have those suggestions, I will produce a "poll" of suggested date/times and topics.

When the above is completed, I plan to turn it over to the volunteer owner/administrator.

I am looking forward to this.

Bill
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Sat, Apr 18, 2020 at 8:26 AM Brian Riggs <7briggs@...> wrote:
As a future SM2k owner, I'd love to lurk as well.

Cheers!
Brian Riggs

On Sat, Apr 18, 2020, 09:20 Porter McRoberts via groups.io <portermcroberts=yahoo.com@groups.io> wrote:
Love to be a part of this. Regardless of topics.
Porter 
S/v ibis


On Apr 18, 2020, at 9:03 AM, HOFMEYR SCHOLTZ <hoffi@...> wrote:

I there,
I'm a near-future Amel owner. If you'd have me please count me in.
Hofmeyr


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

 

All,

I am going to wait a few more days to be able to get some more comments. I have been contacted by one group member who is an experienced ZOOM administrator and has a commercial account with ZOOM. This will benefit all of us.

Those interested please reply to this thread with their suggested topic(s), or any other suggestions. Once I have those suggestions, I will produce a "poll" of suggested date/times and topics.

When the above is completed, I plan to turn it over to the volunteer owner/administrator.

I am looking forward to this.

Bill
CW Bill Rouse Amel Owners Yacht School
Address: 720 Winnie, Galveston Island, Texas 77550 
View My Training Calendar


On Sat, Apr 18, 2020 at 8:26 AM Brian Riggs <7briggs@...> wrote:
As a future SM2k owner, I'd love to lurk as well.

Cheers!
Brian Riggs

On Sat, Apr 18, 2020, 09:20 Porter McRoberts via groups.io <portermcroberts=yahoo.com@groups.io> wrote:
Love to be a part of this. Regardless of topics.
Porter 
S/v ibis


On Apr 18, 2020, at 9:03 AM, HOFMEYR SCHOLTZ <hoffi@...> wrote:

I there,
I'm a near-future Amel owner. If you'd have me please count me in.
Hofmeyr


Re: 𝗭𝗢𝗢𝗠 𝗴𝗲𝘁 𝘁𝗼𝗴𝗲𝘁𝗵𝗲𝗿

Brian Riggs
 

As a future SM2k owner, I'd love to lurk as well.

Cheers!
Brian Riggs

On Sat, Apr 18, 2020, 09:20 Porter McRoberts via groups.io <portermcroberts=yahoo.com@groups.io> wrote:
Love to be a part of this. Regardless of topics.
Porter 
S/v ibis


On Apr 18, 2020, at 9:03 AM, HOFMEYR SCHOLTZ <hoffi@...> wrote:

I there,
I'm a near-future Amel owner. If you'd have me please count me in.
Hofmeyr