Date   

Re: [Amel Yacht Owners] Racor Fuel Filter/Water Separator

amelforme
 

Hi Jerry,

At the AMEL Shipyard, we offer a dual Racor Filter with
manifold and vacuum gauge as an option. This allowed one to
switch to a clean filter in an emergency (they never fail in
open seas with flat water) and change the dirty one when
more convenient.

Even if an engine only burns a maximum of 6 GPH, like your
Volvo, it passes many times that amount through the
injection pump each hour to lubricate and cool the pump.
The excess is returned to the tank via the return line.

I would use a single 500 series RACOR at the minimum and
think the dual 75500 MAX2 setup is the best way to go.

Hope this helps.

Joel F. Potter,
AMEL 54, Hull # 14, HOLLIS


Re: [Amel Yacht Owners] Racor Fuel Filter/Water Separator

Eric Lindholm
 

That should be more than adequate, the largest Detroit Diesels flow 100 gph. Eric 105

PFM53 <pfm53@...> wrote: Does anyone know what size Racor fuel filter/water separator is recommended
for the Volvo TMD22? I would think that the 60 GPH (227LPH) size should be
sufficient, but I haven't been able to determine the specific GPH requirements
for this engine.

Thanks

Jerry






SPONSORED LINKS
Sailing Sailing yacht Amel Boating sailing

---------------------------------
YAHOO! GROUPS LINKS


Visit your group "amelyachtowners" on the web.

To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


---------------------------------


Racor Fuel Filter/Water Separator

PFM53 <pfm53@...>
 

Does anyone know what size Racor fuel filter/water separator is recommended
for the Volvo TMD22? I would think that the 60 GPH (227LPH) size should be
sufficient, but I haven't been able to determine the specific GPH requirements
for this engine.

Thanks

Jerry


Re: [Amel Yacht Owners] original rigging on maramu

Eric Lindholm
 

My maramu has a fixed "top stay" between the masts. Eric 105

sy melmar y <newsgroup@...> wrote: hello
could anyone please tell me if originally the two masts were
interconectet by a "top stay"? on our maramu (1981) a stay is running
from the main mast top over a block/roll on the mizzen top down along
the mizzen to a point just above the block/roll of the mainsheet. since
i heard too many voices to remove it, i'm wondering if the amels put it
there.
similar question: the aftstay of the mizzen runs to a point on top of
the center pushpit or to the foot of the center pushpit? the welding
seems not to be original on our stern...
thanks,
marc, MELMAR Y, maramu #89, www.melmar.ch





SPONSORED LINKS
Sailing Sailing yacht Amel Boating sailing

---------------------------------
YAHOO! GROUPS LINKS


Visit your group "amelyachtowners" on the web.

To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


---------------------------------


original rigging on maramu

sy melmar y <newsgroup@...>
 

hello
could anyone please tell me if originally the two masts were
interconectet by a "top stay"? on our maramu (1981) a stay is running
from the main mast top over a block/roll on the mizzen top down along
the mizzen to a point just above the block/roll of the mainsheet. since
i heard too many voices to remove it, i'm wondering if the amels put it
there.
similar question: the aftstay of the mizzen runs to a point on top of
the center pushpit or to the foot of the center pushpit? the welding
seems not to be original on our stern...
thanks,
marc, MELMAR Y, maramu #89, www.melmar.ch


rings in aft cabin on maramu

sy melmar y <newsgroup@...>
 

since i don't have had any possibility to talk and ask one of the
preowners of my maramu #89 a (maybe silly) question: in our aft cabin
there are two quite strong rings screwed in - one fwd just between the
entry door to the aft cabin and the little hatch to the cockpit, the
other one aft at the foot end of the beds on the center post. what are
they for? i want to keep/reinstate our maramu as original as possible. i
figuered that the amels did think something on most of the things they
were building in their boats. thanks for any hints.
marc, MELMAR Y, maramu #89, www.melmar.ch


Re: [Amel Yacht Owners] double bed in salon on maramu

sy melmar y <newsgroup@...>
 

after reading your message i went on to search behind the folding table
... and of course i found the four holes of the original plate (with the
pipe according to your description). eric: no picture necessary, thanks
for the offer. i just have to find an easy way to get to a similar
support somewhere. thanks.
marc, MELMAR Y, maramu #89, www.melmar.ch

-----Original Message-----
From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of Eric Lindholm
Sent: Montag, 20. März 2006 06:05
To: amelyachtowners@...
Subject: RE: [Amel Yacht Owners] double bed in salon on maramu

On the port aft side of the pedestal, the pipe sticks out from the
pedestal and through the hole in the leaf of the table when it is down
to make the bed on the port side. It is either polished stainless steel
or chrome plated. It is at the height of the top of the port seat. The
extended board rests on the seat all along the port side, the seat fore,
and the pipe on the port side of the pedestal, for its starboard support
aft. I can take a picture and email it to you next time I am at the
boat. Eric

sy melmar y <newsgroup@...> wrote: thanks for replys. it looks to
me that the folded down table takes ‚the
whole weight’ on the stb side of the bed... ok.
eric: just to get it right. the original pipe is affixed to the pedestal
- the one in the middle through the „two inch hole“ or towards the
seatinglocker on port side?
marc, S/Y MELMAR Y, maramu #89

-----Original Message-----
From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of Eric Lindholm
Sent: Donnerstag, 16. März 2006 21:27
To: amelyachtowners@...
Subject: RE: [Amel Yacht Owners] double bed in salon on maramu

On my Maramu the extended board rests on the lip of the seat forward,
and a small pipe sticks out of the "two inch hole" in the table when it
is folded down to support the other end aft. The original pipe is
approx 1" diameter by 4" long and affixed to the pedestal. Eric 105

Horst Pause <horst@...> wrote: On my Maramu the folded out
part of the double bed rests against the lip
on the folded down table, which has worked quite well so far. Whilst I
don't know whether this is the original feature, I have seen the same
arrangement on other Maramus.

Good luck with your rebuild.
Horst, Maramu 185

________________________________

From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of sy melmar y
Sent: 16 March 2006 15:38
To: amelyachtowners@...
Subject: [Amel Yacht Owners] double bed in salon on maramu

hello
i'm tying to reinstate some 'lost' original installations on our maramu.
one of them being the double bed on port side in the salon. putting the
second wooden board under the port bench board is the easy part. this
one folds out toward the mid pedestal. fwd it lies on the short cross
bench. on the aft side it must lie on something as well. is the about
two inch hole in the down folded table the solution? could anybody show
or explain the item which was originally installed for that purpose?
thanks.
marc, S/Y MELMAR Y, maramu #89


Re: Anchor Chain

bobparry1947 <bob@...>
 

When we bought our SM in 2004, she came with 50m of 8mm chain. Last
year, we bought a new gypsy from Amel but you should be able to get
one from a Lofrans distributor as listed on their website or any
Lofrans supplier. We now have 90m (we had ordered 100m) of 10mm short
link hot dipped chain. Be aware that there are two sizes of short link
so match the chain to the gypsy. We have an anchor swivel between the
anchor and the chain.

We don't have a problem with storing the chain in the chain locker and
have not had any problems in that area. Nor is the weight a problem.
We did find that the chain peeler was catching the chain as we brought
it in. As we were not able to easily get a new one, we took it off. So
far, that has worked well. Don't use rope near coral.

Can't help with chain suppliers as our boat is in the Med and we are
Australian.

Bob and Ann Parry
Nowornot SM#33

--- In amelyachtowners@..., "mike_ondra" <mondra@...> wrote:

Having purchased "Drifter" SM #240 in October we are having great fun
exploring and beginning to understand some of the myriad systems on
board. Recently checking the anchor chain locker for the first time
from the fore stateroom, we found a mound of rusted chain requiring a
hammer to break it up. Me-thinks it time to replace the chain.

Being in the US, metric chain seems unatainable, hence a potential
incompatibility with the windlass gypsy. Anyway, looking for
suggestions, knowing that there are probably as many opinions about
anchoring as there are skippers.

1) Recommended size/type chain. Thinking 3/8" G40 or G70, but can a
replacement gypsy for that size chain be found for this windlass.
Alternatively, is metric chain available in the US at palatable prices.

2) Recommended rode configuration. Thinking 100-150' of chain and
100'-150' of rope. Planning cruising in Caribbean and South Pacific.

Thanks for any help with this,

Mike Ondra
"Drifter" SM #240


Re: [Amel Yacht Owners] Muffler question

asm283 <no_reply@...>
 

Hi Joel

Thank you for the information. I will contact Olivier. I can get
Vetus products here. Hows the 54.

Vito

ASM # 283

Wanderer


--- In amelyachtowners@..., "Joel F. Potter"
<jfpottercys@...> wrote:

Hi Vito,

That muffler is aluminum, not stainless. They are not able
to be repaired. Trust me. We tried twice and the only one
who was happy was the welding supplies store.

AMEL went to a plastic/poly type on later boats from VETUS.
The advantage was that they don't corrode and since they are
"flexible" they eliminated vibration and were a little more
quiet. The big negative is they melt if the raw water
injection at the exhaust elbow goes away. All in all, most
folks like them better than the original or the fiberglass
pot-type Aqua Lift brand mufflers. Perhaps Olivier could
supply us with the model number and any installation tips.
Hey Olivier...

All the best,
Joel F. Potter
AMEL 54 Hull # 14, HOLLIS


Re: [Amel Yacht Owners] Muffler question

amelforme
 

Hi Vito,

That muffler is aluminum, not stainless. They are not able
to be repaired. Trust me. We tried twice and the only one
who was happy was the welding supplies store.

AMEL went to a plastic/poly type on later boats from VETUS.
The advantage was that they don't corrode and since they are
"flexible" they eliminated vibration and were a little more
quiet. The big negative is they melt if the raw water
injection at the exhaust elbow goes away. All in all, most
folks like them better than the original or the fiberglass
pot-type Aqua Lift brand mufflers. Perhaps Olivier could
supply us with the model number and any installation tips.
Hey Olivier...

All the best,
Joel F. Potter
AMEL 54 Hull # 14, HOLLIS


Re: [Amel Yacht Owners] Anchor Chain

Thomas.Neuland@t-online.de <thomas.neuland@...>
 

Dear Mike,

I had the same question as you had- the chain was just too short, old
and way too light.
We had a modification done at Amel's shipyard in Hyeres and the
recommended 76 m of 10 mm nickeled (not stainless) chain with just
another nutwheel on the Lofrans windlass. It is a super combination. The
lenghth is just right because it is not resulting in "chain-mountains"
inside the chain-house.
Do yourself a favor and add a turning clutch between anchor and chain
since the chain tends to get twisted a this lenghths. About non-metric
sizes I don't know of course, but Amel's info and support was (again)
superb.

Fair winds.

Tom Neuland
"Mallamok"
SM # 003

-----Original Message-----
Date: Fri, 10 Mar 2006 04:06:37 +0100
Subject: [Amel Yacht Owners] Anchor Chain
From: "mike_ondra"
To: amelyachtowners@...

Having purchased "Drifter" SM #240 in October we are having great fun
exploring and beginning to understand some of the myriad systems on
board. Recently checking the anchor chain locker for the first time
from the fore stateroom, we found a mound of rusted chain requiring a
hammer to break it up. Me-thinks it time to replace the chain.

Being in the US, metric chain seems unatainable, hence a potential
incompatibility with the windlass gypsy. Anyway, looking for
suggestions, knowing that there are probably as many opinions about
anchoring as there are skippers.

1) Recommended size/type chain. Thinking 3/8" G40 or G70, but can a
replacement gypsy for that size chain be found for this windlass.
Alternatively, is metric chain available in the US at palatable prices.

2) Recommended rode configuration. Thinking 100-150' of chain and
100'-150' of rope. Planning cruising in Caribbean and South Pacific.

Thanks for any help with this,

Mike Ondra
"Drifter" SM #240









Yahoo! Groups Links


Re: [Amel Yacht Owners] double bed in salon on maramu

Eric Lindholm
 

On the port aft side of the pedestal, the pipe sticks out from the pedestal and through the hole in the leaf of the table when it is down to make the bed on the port side. It is either polished stainless steel or chrome plated. It is at the height of the top of the port seat. The extended board rests on the seat all along the port side, the seat fore, and the pipe on the port side of the pedestal, for its starboard support aft. I can take a picture and email it to you next time I am at the boat. Eric

sy melmar y <newsgroup@...> wrote: thanks for replys. it looks to me that the folded down table takes ‚the
whole weight’ on the stb side of the bed... ok.
eric: just to get it right. the original pipe is affixed to the pedestal
- the one in the middle through the „two inch hole“ or towards the
seatinglocker on port side?
marc, S/Y MELMAR Y, maramu #89

-----Original Message-----
From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of Eric Lindholm
Sent: Donnerstag, 16. März 2006 21:27
To: amelyachtowners@...
Subject: RE: [Amel Yacht Owners] double bed in salon on maramu

On my Maramu the extended board rests on the lip of the seat forward,
and a small pipe sticks out of the "two inch hole" in the table when it
is folded down to support the other end aft. The original pipe is
approx 1" diameter by 4" long and affixed to the pedestal. Eric 105

Horst Pause <horst@...> wrote: On my Maramu the folded out
part of the double bed rests against the lip
on the folded down table, which has worked quite well so far. Whilst I
don't know whether this is the original feature, I have seen the same
arrangement on other Maramus.

Good luck with your rebuild.
Horst, Maramu 185


________________________________

From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of sy melmar y
Sent: 16 March 2006 15:38
To: amelyachtowners@...
Subject: [Amel Yacht Owners] double bed in salon on maramu

hello
i'm tying to reinstate some 'lost' original installations on our maramu.
one of them being the double bed on port side in the salon. putting the
second wooden board under the port bench board is the easy part. this
one folds out toward the mid pedestal. fwd it lies on the short cross
bench. on the aft side it must lie on something as well. is the about
two inch hole in the down folded table the solution? could anybody show
or explain the item which was originally installed for that purpose?
thanks.
marc, S/Y MELMAR Y, maramu #89





SPONSORED LINKS
Sailing Sailing yacht Amel Boating sailing

---------------------------------
YAHOO! GROUPS LINKS


Visit your group "amelyachtowners" on the web.

To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


---------------------------------


Re: [Amel Yacht Owners] Muffler question

Eric Lindholm
 

Yes it does. You will probably get more as time goes on. You will probably have to either replace it or fiberglass the whole muffler. Eric maramu 105

asm283 <no_reply@...> wrote: Hello

I have the Volvo engine on my SM. There is a hole in the middle of the
stainless steel muffler. There is some rust buildup in this hole as
well as some slight weeping. Has anyone had this problem. Does this
mean that the muffler is rusting from within.

Thank you

Vito Ciaravino

ASM 283





SPONSORED LINKS
Sailing Sailing yacht Amel Boating sailing

---------------------------------
YAHOO! GROUPS LINKS


Visit your group "amelyachtowners" on the web.

To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


---------------------------------


Muffler question

asm283 <no_reply@...>
 

Hello

I have the Volvo engine on my SM. There is a hole in the middle of the
stainless steel muffler. There is some rust buildup in this hole as
well as some slight weeping. Has anyone had this problem. Does this
mean that the muffler is rusting from within.

Thank you

Vito Ciaravino

ASM 283


Re: [Amel Yacht Owners] fueltank inspection holes on maramu

sy melmar y <newsgroup@...>
 

ok. i'm really surprised... but then we will have to do those works next
year with an empty tank!
marc, MELMAR Y, maramu #89

-----Original Message-----
From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of David Wallace
Sent: Freitag, 17. März 2006 21:34
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] fueltank inspection holes on maramu

I concur with Eric. Friends of ours with a sister ship had an
inspection
port installed a couple of years ago. Not a major task except for
making
sure the metal bits are out of the tank after cutting the access port.
But
if the goal is to clean the tank anyway.... At the same time, they also

installed a TankTender fuel gage, the non-electric kind that uses air
pressure and said it worked fine. I don't know the cost of any of this.

Dave
sv Air Ops
Maramu #104

From: Eric Lindholm <etlindholm@...>
Reply-To: amelyachtowners@...
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] fueltank inspection holes on maramu
Date: Thu, 16 Mar 2006 12:27:17 -0800 (PST)

I didn't find any either. Eric 105

sy melmar y <newsgroup@...> wrote: hi there
follwoing the fuel polishing issue i'm planning do have some work done
on our fuel system. taking the top cover board off the fuel tank i
expected to find some inspection holes for a first check. can't find
them. any hint?
marc, MELMAR Y, maramu #89


Re: [Amel Yacht Owners] double bed in salon on maramu

sy melmar y <newsgroup@...>
 

thanks for replys. it looks to me that the folded down table takes ‚the
whole weight’ on the stb side of the bed... ok.
eric: just to get it right. the original pipe is affixed to the pedestal
- the one in the middle through the „two inch hole“ or towards the
seatinglocker on port side?
marc, S/Y MELMAR Y, maramu #89

-----Original Message-----
From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of Eric Lindholm
Sent: Donnerstag, 16. März 2006 21:27
To: amelyachtowners@...
Subject: RE: [Amel Yacht Owners] double bed in salon on maramu

On my Maramu the extended board rests on the lip of the seat forward,
and a small pipe sticks out of the "two inch hole" in the table when it
is folded down to support the other end aft. The original pipe is
approx 1" diameter by 4" long and affixed to the pedestal. Eric 105

Horst Pause <horst@...> wrote: On my Maramu the folded out
part of the double bed rests against the lip
on the folded down table, which has worked quite well so far. Whilst I
don't know whether this is the original feature, I have seen the same
arrangement on other Maramus.

Good luck with your rebuild.
Horst, Maramu 185


________________________________

From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of sy melmar y
Sent: 16 March 2006 15:38
To: amelyachtowners@...
Subject: [Amel Yacht Owners] double bed in salon on maramu

hello
i'm tying to reinstate some 'lost' original installations on our maramu.
one of them being the double bed on port side in the salon. putting the
second wooden board under the port bench board is the easy part. this
one folds out toward the mid pedestal. fwd it lies on the short cross
bench. on the aft side it must lie on something as well. is the about
two inch hole in the down folded table the solution? could anybody show
or explain the item which was originally installed for that purpose?
thanks.
marc, S/Y MELMAR Y, maramu #89


Re: [Amel Yacht Owners] fueltank inspection holes on maramu

David Wallace
 

I concur with Eric. Friends of ours with a sister ship had an inspection port installed a couple of years ago. Not a major task except for making sure the metal bits are out of the tank after cutting the access port. But if the goal is to clean the tank anyway.... At the same time, they also installed a TankTender fuel gage, the non-electric kind that uses air pressure and said it worked fine. I don't know the cost of any of this.

Dave
sv Air Ops
Maramu #104

From: Eric Lindholm <etlindholm@...>
Reply-To: amelyachtowners@...
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] fueltank inspection holes on maramu
Date: Thu, 16 Mar 2006 12:27:17 -0800 (PST)

I didn't find any either. Eric 105

sy melmar y <newsgroup@...> wrote: hi there
follwoing the fuel polishing issue i'm planning do have some work done
on our fuel system. taking the top cover board off the fuel tank i
expected to find some inspection holes for a first check. can't find
them. any hint?
marc, MELMAR Y, maramu #89





SPONSORED LINKS
Sailing Sailing yacht Amel Boating sailing

---------------------------------
YAHOO! GROUPS LINKS


Visit your group "amelyachtowners" on the web.

To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


---------------------------------







Re: [Amel Yacht Owners] fueltank inspection holes on maramu

Eric Lindholm
 

I didn't find any either. Eric 105

sy melmar y <newsgroup@...> wrote: hi there
follwoing the fuel polishing issue i'm planning do have some work done
on our fuel system. taking the top cover board off the fuel tank i
expected to find some inspection holes for a first check. can't find
them. any hint?
marc, MELMAR Y, maramu #89





SPONSORED LINKS
Sailing Sailing yacht Amel Boating sailing

---------------------------------
YAHOO! GROUPS LINKS


Visit your group "amelyachtowners" on the web.

To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


---------------------------------


Re: [Amel Yacht Owners] double bed in salon on maramu

Eric Lindholm
 

On my Maramu the extended board rests on the lip of the seat forward, and a small pipe sticks out of the "two inch hole" in the table when it is folded down to support the other end aft. The original pipe is approx 1" diameter by 4" long and affixed to the pedestal. Eric 105

Horst Pause <horst@...> wrote: On my Maramu the folded out part of the double bed rests against the lip
on the folded down table, which has worked quite well so far. Whilst I
don't know whether this is the original feature, I have seen the same
arrangement on other Maramus.



Good luck with your rebuild.



Horst, Maramu 185



________________________________

From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of sy melmar y
Sent: 16 March 2006 15:38
To: amelyachtowners@...
Subject: [Amel Yacht Owners] double bed in salon on maramu



hello
i'm tying to reinstate some 'lost' original installations on our maramu.
one of them being the double bed on port side in the salon. putting the
second wooden board under the port bench board is the easy part. this
one folds out toward the mid pedestal. fwd it lies on the short cross
bench. on the aft side it must lie on something as well. is the about
two inch hole in the down folded table the solution? could anybody show
or explain the item which was originally installed for that purpose?
thanks.
marc, S/Y MELMAR Y, maramu #89






SPONSORED LINKS

Sailing
<http://groups.yahoo.com/gads?t=ms&k=Sailing&w1=Sailing&w2=Sailing+yacht
&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=PlhCW0zvsb13KReuHX3A-Q>

Sailing yacht
<http://groups.yahoo.com/gads?t=ms&k=Sailing+yacht&w1=Sailing&w2=Sailing
+yacht&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=SzbkQjL-eN7E93cbJzL0eQ>


Amel
<http://groups.yahoo.com/gads?t=ms&k=Amel&w1=Sailing&w2=Sailing+yacht&w3
=Amel&w4=Boating+sailing&c=4&s=63&.sig=pKnE4krYP80ImoJWH3305w>

Boating sailing
<http://groups.yahoo.com/gads?t=ms&k=Boating+sailing&w1=Sailing&w2=Saili
ng+yacht&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=-PqrRug6_9dlpPCqNcYXvA






________________________________

YAHOO! GROUPS LINKS



* Visit your group "amelyachtowners
<http://groups.yahoo.com/group/amelyachtowners> " on the web.

* To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...
<mailto:amelyachtowners-unsubscribe@...?subject=Unsubscribe>


* Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service <http://docs.yahoo.com/info/terms/> .



________________________________







SPONSORED LINKS
Sailing Sailing yacht Amel Boating sailing

---------------------------------
YAHOO! GROUPS LINKS


Visit your group "amelyachtowners" on the web.

To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


---------------------------------


Re: [Amel Yacht Owners] double bed in salon on maramu

Horst Pause <horst@...>
 

On my Maramu the folded out part of the double bed rests against the lip
on the folded down table, which has worked quite well so far. Whilst I
don't know whether this is the original feature, I have seen the same
arrangement on other Maramus.



Good luck with your rebuild.



Horst, Maramu 185



________________________________

From: amelyachtowners@...
[mailto:amelyachtowners@...] On Behalf Of sy melmar y
Sent: 16 March 2006 15:38
To: amelyachtowners@...
Subject: [Amel Yacht Owners] double bed in salon on maramu



hello
i'm tying to reinstate some 'lost' original installations on our maramu.
one of them being the double bed on port side in the salon. putting the
second wooden board under the port bench board is the easy part. this
one folds out toward the mid pedestal. fwd it lies on the short cross
bench. on the aft side it must lie on something as well. is the about
two inch hole in the down folded table the solution? could anybody show
or explain the item which was originally installed for that purpose?
thanks.
marc, S/Y MELMAR Y, maramu #89






SPONSORED LINKS

Sailing
<http://groups.yahoo.com/gads?t=ms&k=Sailing&w1=Sailing&w2=Sailing+yacht
&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=PlhCW0zvsb13KReuHX3A-Q>

Sailing yacht
<http://groups.yahoo.com/gads?t=ms&k=Sailing+yacht&w1=Sailing&w2=Sailing
+yacht&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=SzbkQjL-eN7E93cbJzL0eQ>


Amel
<http://groups.yahoo.com/gads?t=ms&k=Amel&w1=Sailing&w2=Sailing+yacht&w3
=Amel&w4=Boating+sailing&c=4&s=63&.sig=pKnE4krYP80ImoJWH3305w>

Boating sailing
<http://groups.yahoo.com/gads?t=ms&k=Boating+sailing&w1=Sailing&w2=Saili
ng+yacht&w3=Amel&w4=Boating+sailing&c=4&s=63&.sig=-PqrRug6_9dlpPCqNcYXvA






________________________________

YAHOO! GROUPS LINKS



* Visit your group "amelyachtowners
<http://groups.yahoo.com/group/amelyachtowners> " on the web.

* To unsubscribe from this group, send an email to:
amelyachtowners-unsubscribe@...
<mailto:amelyachtowners-unsubscribe@...?subject=Unsubscribe>


* Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service <http://docs.yahoo.com/info/terms/> .



________________________________