Date   

Small cracks in helm spokes

briantrautman@ymail.com <briant@...>
 

Hello,

We recently observed two small cracks branching out from the base of one of the spokes of our helm wheel. The cracks are about 1.5 inches along the back of the hub that attaches to the steering mechanism (not the side with the signed Henri Amel plaque)

I haven't determined if these are cosmetic only or part of the load bearing structure of the helm. I was wondering if anyone had seen this on their SM, and if so what did you do to fix it?

Thank you!
Brian Trautman
Delos, SM 2000 #303
Seattle, WA


Re: [Amel] Lee Sails for Sharki 104

Dave_Benjamin
 

The sailmakers you mention have their sails built in China but they use
another loft, one that I am quite familiar with. In fact Nigel Calder
wrote an in depth article about the loft for a British periodical. I'd
be happy to send a copy to anyone interested. The article even names those sailmakers.

Teijin is not well regarded by most sailmakers. Lee Sails Northeast advertises on their website that they use Challenge and Bainbridge.It's a far cry from the higher end cloth from Dimension Polyant, Bainbridge, Challenge, and Contender. It is cheap though.  I've used Teijin cloth on occasion for some small boat projects like a set of sails for a 13 foot daysailer that is  used by children for daysailing on a lake. There are several lofts using Teijin produced cloth for small boat and Hobie Cat sails. It allows them to keep the costs way down. For instance there is a supplier here in the US that sells Laser sails for about $170 USD that uses Teijin. Another loft sells Hobie Cat sails starting as low as $400 or so. It is an appropriate cloth when cost is the primary consideration.

The amount you paid for your sails is less than the cost of cloth and shipping finished sails from Asia to Europe or North America. If Teijin put out a good quality cloth that was comparable with the manufacturers I mentioned, reptuable sailmakers would be using it in quantity.

Caution is in order for anyone ordering direct from Lee Sails in China. They require payment by wire transfer or bank check. You should never buy anything like a sail unless you can use a credit card as there is no recourse in the event of problems. You can contest a charge made with a credit card successfully. I had a dock neighbor who tried to save some money and ordered a sail from a loft quite some distance away. The sail was a disaster and when the sailmaker failed to address the issue he was able to contest the chrage and get his money refunded.

--- On Sun, 5/17/09, etske <amel.sharki.charmedii@gmail.com> wrote:

From: etske <amel.sharki.charmedii@gmail.com>
Subject: Re: [Amel] Lee Sails for Sharki 104
To: amelyachtowners@yahoogroups.com
Date: Sunday, May 17, 2009, 1:57 PM

















Dear Dave,



Your misinterpretating my words (maybe because of the quality of my english). I did not say the are flat without shape I said they are flat without loosing their shape.



But even when you misunderstood your comments are wrong.



First, the sails are made from 1st quality dracron It comes from Tejin wich is Du pont (the founder of dracron)(since they use 250000 sq metres per annum I don't think there's enough B quality ;-))



Second, I tried to explain that I found it very good they understood I wanted a different kind of sail GI GII in character. The GI is great for average cruising but for (dutch average 4 a 5 SW) sportive sailing the GII is flatter and better upwind.



Before I ordered I did some research and in Holland they are pretty well known (the produce for Quantum, Elvstrom and UK sails to name a few. The runner up of the IJspegelcup (biggest winter matches in Holland) had 3 year old Leesails. When I spoke with him he told me this was the first time he could use sails more than a season.

Without getting into a discussion about this company (I don't own them) ;-)). In files I put an article about Lee Sails.



And in Pictures you cen see us sailing with the new sails...




























[Non-text portions of this message have been removed]


Re: [Amel] Re: Verical Batons

karkauai
 

I had the Banks loft in Kemah, Tx build them.  Trent and Mark (last names escape me right now) were the ones I dealt with, good guys and did a great job.
 
Stuck in Charleston, SC waiting out this storm after 10 days in the Bahamas and won't have time to get her up to the Chesapeake before I have to go back to work, so having some time to work on a few things.  Still no solution to the engine RPM problem, but realized that there is a good bit of smoke after motoring across from Abaco in light winds right on the stern (still haven't got her rigged to use the downwind setup), the whole aft port topsides are soot stained.  Starting to think it's an air issue rather than a fuel issue.  Will follow up on all the great advice the group offered this week.  Anybody have a good experience with a diesel mechanic in Charleston?
 
Anybody have any advice on getting the hi pressure hoses on the watermaker to stay on?  Ray Eaton said he found one off while the boat was in Ft. Lauderdale and fixed it, but it blew off again as soon as I turned the watermaker on.  Couldn't get it to stay after several tries,  so had a compression fitting one made in Marsh Harbor.  That one stayed on but the next one down the line blew off at 50 psi.  Whazzup widat?
 
Met George at the Charleston City Marina on Indecent...my first encounter "out there" with another Amel.  Pretty cool.
 
Thanks for all the group's advice, don't know what I'd do without you.
Kent Robertson
Kristy SM 243

--- On Sun, 5/17/09, Dave Benjamin <dave_benjamin@yahoo.com> wrote:


From: Dave Benjamin <dave_benjamin@yahoo.com>
Subject: Re: [Amel] Re: Verical Batons
To: amelyachtowners@yahoogroups.com
Date: Sunday, May 17, 2009, 2:00 PM








Which Banks Sails loft were you working with? I used to work for Banks Sails in Florida and hat a lot of fun there. I still have some good friends involved with Banks. There's a lot of talent in that group but of course I'd rather see people buy sails from us ;-)

--- On Sat, 5/16/09, karkauai <karkauai@yahoo. com> wrote:

From: karkauai <karkauai@yahoo. com>
Subject: [Amel] Re: Verical Batons
To: amelyachtowners@ yahoogroups. com
Date: Saturday, May 16, 2009, 9:44 PM

Banks Sails made my new main with vertical battens, and they really do seem to give the sail a better shape than other non-battened in mast furling sails. They easily roll into the mast as long as a little pressure is maintained on the outhaul while the sail is furled and unfurled.











[Non-text portions of this message have been removed]
















[Non-text portions of this message have been removed]


Re: [Amel] Lee Sails for Sharki 104

Hajé Weisfelt
 

Dear Dave,

Your misinterpretating my words (maybe because of the quality of my english). I did not say the are flat without shape I said they are flat without loosing their shape.

But even when you misunderstood your comments are wrong.

First, the sails are made from 1st quality dracron It comes from Tejin wich is Du pont (the founder of dracron)(since they use 250000 sq metres per annum I don't think there's enough B quality ;-))

Second, I tried to explain that I found it very good they understood I wanted a different kind of sail GI GII in character. The GI is great for average cruising but for (dutch average 4 a 5 SW) sportive sailing the GII is flatter and better upwind.

Before I ordered I did some research and in Holland they are pretty well known (the produce for Quantum, Elvstrom and UK sails to name a few. The runner up of the IJspegelcup (biggest winter matches in Holland) had 3 year old Leesails. When I spoke with him he told me this was the first time he could use sails more than a season.
Without getting into a discussion about this company (I don't own them) ;-)). In files I put an article about Lee Sails.

And in Pictures you cen see us sailing with the new sails...


Re: [Amel] Verical Batons

john martin <symoondog@...>
 

Jim, another thought, the in mast batten free sail is a proven passage maker. Battens in the main with some roach in it will improve your windward performance I will agree to that. Just remember when you have to reef the main you'll have to go head to wind. When you get hit by heavy air you release the jib and main sheets. you then must get in all the jib to put the boat head to wind. The boom will be flailing out on your beam and will be head to wind but your bow isn't. If its blowing 45 knots the bow won't come to windward unless you sheet it back in, but you have a full main and you'l be trying to sheet it in while standing the boat on its beam ends. You will end up starting the motor to drive the boat up so you can get the boom lined up with the slot in the main, if there's any main left by now it just might work. This scenario is so easy with Amels way, we just ease the main out hawl and roll up some sail and never change course regardless of wind speed or direction. If I had a reverse gear in my electric jib sheet winch, I'd never leave the helmsmen seat to do anything. What part of this do you not like? If you insist on this go a little faster ideal,make sure you don't go to the Med and get hit by one of their Mistrals, or the Atlantic and get caught in a white squall or where I just came from, 50 degree south and get blindsided by a 55 kt. williwaw blasting down a mountain.
John "Moon Dog" SM 248


To: amelyachtowners@yahoogroups.com
From: dave_benjamin@yahoo.com
Date: Tue, 12 May 2009 23:21:30 -0700
Subject: Re: [Amel] Verical Batons







Jim,

As a sailmaker I am not enthused with vertical battens although there are some vocal proponents. There are issues with vertical battens getting stuck and causing problems. On a cruising boat you really don't want that risk.

Has your sailmaker built sails for a SM before? I saw one SM where a sailmaker made the sail a bit too long on the luff and built patches that were bulky. The sail required several modifications to fit properly.

--- On Tue, 5/12/09, linda.desalvo <linda.desalvo@yahoo.com> wrote:

From: linda.desalvo <linda.desalvo@yahoo.com>
Subject: [Amel] Verical Batons
To: amelyachtowners@yahoogroups.com
Date: Tuesday, May 12, 2009, 4:32 PM

Hello All

We are in the process of ordering a new mainsail for our Super Maramu #207 and would like any feedback that we could get in reference to vertical batons. Are they something that would enhance the sail. Does anyone out there have a mainsail with vertical baton and what kind of performance does this type of sail give? Could they get stuck in the roller furling? Any advise or comments would be greatly appreciated.

Jim DeSalvo

SV Liebling





















_________________________________________________________________
Windows Live: Keep your life in sync.
http://windowslive.com/explore?ocid=TXT_TAGLM_BR_life_in_synch_052009

[Non-text portions of this message have been removed]


Re: [Amel] Re: Verical Batons

Dave_Benjamin
 

Which Banks Sails loft were you working with? I used to work for Banks Sails in Florida and hat a lot of fun there. I still have some good friends involved with Banks. There's a lot of talent in that group but of course I'd rather see people buy sails from us ;-)

--- On Sat, 5/16/09, karkauai <karkauai@yahoo.com> wrote:

From: karkauai <karkauai@yahoo.com>
Subject: [Amel] Re: Verical Batons
To: amelyachtowners@yahoogroups.com
Date: Saturday, May 16, 2009, 9:44 PM

















Banks Sails made my new main with vertical battens, and they really do seem to give the sail a better shape than other non-battened in mast furling sails. They easily roll into the mast as long as a little pressure is maintained on the outhaul while the sail is furled and unfurled.




























[Non-text portions of this message have been removed]


Re: Verical Batons

karkauai
 

Banks Sails made my new main with vertical battens, and they really do seem to give the sail a better shape than other non-battened in mast furling sails. They easily roll into the mast as long as a little pressure is maintained on the outhaul while the sail is furled and unfurled.


Re: [Amel] New Sails for Sharki 104

Dave_Benjamin
 

You mention the sails are flat and have little shape. That's a trademark of certain lofts that don't have the ability to produce for the industry and sell direct. Amel owners that want sails that will perform well in a variety of conditions are better served by dealing with a real sailmaker.

You should also know that many of these sails are made with second quality or other manufacturer rejected cloth. That's why they can sell them so cheaply. In many cases I see sails like these being sold for less than what it cost just to buy top quality material.

The bitterness of poor quality outlasts the sweetness of a cheap price.

--- On Sat, 5/16/09, etske <amel.sharki.charmedii@gmail.com> wrote:

From: etske <amel.sharki.charmedii@gmail.com>
Subject: [Amel] New Sails for Sharki 104
To: amelyachtowners@yahoogroups.com
Date: Saturday, May 16, 2009, 2:59 AM

















Dear all,



Since our sails were still the original ones from 1984 we decided to go for new ones. After lots of offers we choose Leesails in Hong Kong. They guaranteed us that they made sails for a Sharki before. We had discussions about several options I wanted (all headsails with foamstrip and UV strip, top batten full, original reefing system with steel wire reinforcing, etc.)

They all did this and for an amazing price. Mizzen, Main, Storm Jib, Furling Jib, Furling Genoa II, Furling Genoa I, alltogether for 6020 US (incl. P&P)!!!!



So you try to find the hook. Sails arrived before the agreed date and all in good order. All sails were tested in the past two weeks and I can't find anything that's not 100% as agreed upon. Main and Mizzen are both flat without loosing there shape, GI is huge and has the rounding where it should be. GII is flat as an high aspect (she does 30 upwind now), Jib we used in a full gale with main down and mizzen up. After three hours with forces up to 10 bft all was perfect OK.



I would advice if asked to go there if you need new sails.



Cheers and fair winds, Hajé




























[Non-text portions of this message have been removed]


Re: [Amel] Anyone with a SHARKI in the UK?

Hajé Weisfelt
 

Not in UK but when in Holland your always welcom aboard.

Cheers, Hajé (Sharki #104)


From: GrahamJohnston42
Sent: Thursday, May 14, 2009 10:14 AM
To: amelyachtowners@yahoogroups.com
Subject: [Amel] Anyone with a SHARKI in the UK?





We looking for a SHarki but have not been on board one for a couple of years and would like to talk to any owners in the UK and if possible see aboard again to refreshh our memories before we start to travel across the EU.

Regards
Graham





[Non-text portions of this message have been removed]


New Sails for Sharki 104

Hajé Weisfelt
 

Dear all,

Since our sails were still the original ones from 1984 we decided to go for new ones. After lots of offers we choose Leesails in Hong Kong. They guaranteed us that they made sails for a Sharki before. We had discussions about several options I wanted (all headsails with foamstrip and UV strip, top batten full, original reefing system with steel wire reinforcing, etc.)
They all did this and for an amazing price. Mizzen, Main, Storm Jib, Furling Jib, Furling Genoa II, Furling Genoa I, alltogether for 6020 US (incl. P&P)!!!!

So you try to find the hook. Sails arrived before the agreed date and all in good order. All sails were tested in the past two weeks and I can't find anything that's not 100% as agreed upon. Main and Mizzen are both flat without loosing there shape, GI is huge and has the rounding where it should be. GII is flat as an high aspect (she does 30 upwind now), Jib we used in a full gale with main down and mizzen up. After three hours with forces up to 10 bft all was perfect OK.

I would advice if asked to go there if you need new sails.

Cheers and fair winds, Hajé


Re: [Amel] 90-260 volt 50-60 cycle chargers

Richard Piller <richard03801@...>
 

Defender now carries the REYA/Dolphin chargers.  You'll have to ask about 24 volts for the SM.  And from what can be seen on their web site they are well priced.
The one shown will do well for 12 Maramu but not the Super Maramu as it needs 80 AMPs.

Keep in mind that if you use a charger rated for to few AMPs your asking for heat and other problems.

Richard and Joan on Challenge SM 209

--- On Fri, 5/15/09, Iv Pepe <iv_pepe@yahoo.com> wrote:

From: Iv Pepe <iv_pepe@yahoo.com>
Subject: Re: [Amel] 90-260 volt 50-60 cycle chargers
To: amelyachtowners@yahoogroups.com
Date: Friday, May 15, 2009, 7:25 AM

















The engin room of SM is verry HOT, abb.50-60 degr.cels.The original "cristec" charger 50A,get cookt! Sekond wan a 60A" cristec" the same story,the garanty das not acsept, the repair! Last year I bot a 60A

"victron energy",work well.The multi volt/smart charger is very clever thing,( Reya ) posible? My englich is not gut, but I hope you understand?

Iv Pepe SM 223



--- El vie, 15/5/09, William Klein <sidecar1@verizon. net> escribió:



De: William Klein <sidecar1@verizon. net>

Asunto: Re: [Amel] 90-260 volt 50-60 cycle chargers

Para: amelyachtowners@ yahoogroups. com

Fecha: viernes, 15 mayo, 2009 5:58



I beleive that you will find Xantrex makes chargers that do the same and they are available at West Marine. I put one in my Maramu and it worked fine. It could be programmed for multiple banks of different battery types and was available in 30A or 50A models.-- Bill Klein

----- Original Message -----

From: Richard Piller

To: amelyachtowners@ yahoogroups. com

Sent: Thursday, May 14, 2009 7:23 PM

Subject: Re: [Amel] 90-260 volt 50-60 cycle chargers



The multi volt/cycle chargers are sold in the US by Dolphin in FL. They are sold in France by Reya. When we are now in NH when we get back to the boat in a week or so we'll post the exact addresses.

Richard and Joan on Challenge SM 209



--- On Thu, 5/14/09, Iv Pepe <iv_pepe@yahoo. com> wrote:



From: Iv Pepe <iv_pepe@yahoo. com>

Subject: Re: [Amel] Iridium Sat Phone Antenna Installation

To: amelyachtowners@ yahoogroups. com

Date: Thursday, May 14, 2009, 4:08 AM



HI,



How can I get, a REY charger?



Iv Pepe SM,223



--- El mié, 13/5/09, Richard Piller <richard03801@ yahoo.com> escribió:



De: Richard Piller <richard03801@ yahoo.com>



Asunto: Re: [Amel] Iridium Sat Phone Antenna Installation



Para: amelyachtowners@ yahoogroups. com



Fecha: miércoles, 13 mayo, 2009 11:38



We mounted ours on the aft rail next to the outboard motor. It works well there and is protected by the motor.



Richard and Joan on Challenge in Annapolis SM 209



--- On Sun, 4/5/09, sv_seabbatical <sv.lonestar@ gmail.com> wrote:



From: sv_seabbatical <sv.lonestar@ gmail.com>



Subject: [Amel] Iridium Sat Phone Antenna Installation



To: amelyachtowners@ yahoogroups. com



Date: Sunday, April 5, 2009, 1:30 PM



I have an Iridium Sat Phone and want to know what kind of antenna installations have been done on Amel 54's. Are they all on the top of the mizzen? Has anyone mounted one on the dodger? All comments will be appreciated.



Craig Scott



LONE STAR



Amel 54 #101



[Non-text portions of this message have been removed]







[Non-text portions of this message have been removed]



[Non-text portions of this message have been removed]



[Non-text portions of this message have been removed]































[Non-text portions of this message have been removed]


Re: [Amel] 90-260 volt 50-60 cycle chargers

Richard Piller <richard03801@...>
 

When using the Reya charger we were able to remove an exhaust fan the prior owners installed to cool? the engine room when the charger was running.  Yes, there is always some heat but the amount now is by far less with the new charger.  Also keep in mind that a 60 Amp charger for a SM is not enough given the size and number of batteries we have to keep charged.  80 Amp is about right.  It is easy on the batteries (gives enough charge) and does not draw beyond the current avaliable in Europe when using their 16 amp outlets.  We do however prefer to use 32 Amps coming in as normal in Europe and 50 Amps in the US and Caribb.
Good luck more details to follow.
Richard and Joan in Annapolis on SM 209

--- On Fri, 5/15/09, Iv Pepe <iv_pepe@yahoo.com> wrote:

From: Iv Pepe <iv_pepe@yahoo.com>
Subject: Re: [Amel] 90-260 volt 50-60 cycle chargers
To: amelyachtowners@yahoogroups.com
Date: Friday, May 15, 2009, 7:25 AM

















The engin room of SM is verry HOT, abb.50-60 degr.cels.The original "cristec" charger 50A,get cookt! Sekond wan a 60A" cristec" the same story,the garanty das not acsept, the repair! Last year I bot a 60A

"victron energy",work well.The multi volt/smart charger is very clever thing,( Reya ) posible? My englich is not gut, but I hope you understand?

Iv Pepe SM 223



--- El vie, 15/5/09, William Klein <sidecar1@verizon. net> escribió:



De: William Klein <sidecar1@verizon. net>

Asunto: Re: [Amel] 90-260 volt 50-60 cycle chargers

Para: amelyachtowners@ yahoogroups. com

Fecha: viernes, 15 mayo, 2009 5:58



I beleive that you will find Xantrex makes chargers that do the same and they are available at West Marine. I put one in my Maramu and it worked fine. It could be programmed for multiple banks of different battery types and was available in 30A or 50A models.-- Bill Klein

----- Original Message -----

From: Richard Piller

To: amelyachtowners@ yahoogroups. com

Sent: Thursday, May 14, 2009 7:23 PM

Subject: Re: [Amel] 90-260 volt 50-60 cycle chargers



The multi volt/cycle chargers are sold in the US by Dolphin in FL. They are sold in France by Reya. When we are now in NH when we get back to the boat in a week or so we'll post the exact addresses.

Richard and Joan on Challenge SM 209



--- On Thu, 5/14/09, Iv Pepe <iv_pepe@yahoo. com> wrote:



From: Iv Pepe <iv_pepe@yahoo. com>

Subject: Re: [Amel] Iridium Sat Phone Antenna Installation

To: amelyachtowners@ yahoogroups. com

Date: Thursday, May 14, 2009, 4:08 AM



HI,



How can I get, a REY charger?



Iv Pepe SM,223



--- El mié, 13/5/09, Richard Piller <richard03801@ yahoo.com> escribió:



De: Richard Piller <richard03801@ yahoo.com>



Asunto: Re: [Amel] Iridium Sat Phone Antenna Installation



Para: amelyachtowners@ yahoogroups. com



Fecha: miércoles, 13 mayo, 2009 11:38



We mounted ours on the aft rail next to the outboard motor. It works well there and is protected by the motor.



Richard and Joan on Challenge in Annapolis SM 209



--- On Sun, 4/5/09, sv_seabbatical <sv.lonestar@ gmail.com> wrote:



From: sv_seabbatical <sv.lonestar@ gmail.com>



Subject: [Amel] Iridium Sat Phone Antenna Installation



To: amelyachtowners@ yahoogroups. com



Date: Sunday, April 5, 2009, 1:30 PM



I have an Iridium Sat Phone and want to know what kind of antenna installations have been done on Amel 54's. Are they all on the top of the mizzen? Has anyone mounted one on the dodger? All comments will be appreciated.



Craig Scott



LONE STAR



Amel 54 #101



[Non-text portions of this message have been removed]



[Non-text portions of this message have been removed]







[Non-text portions of this message have been removed]



[Non-text portions of this message have been removed]


Re: [Amel] 90-260 volt 50-60 cycle chargers

Iv Pepe <iv_pepe@...>
 

The engin room of SM is verry HOT, abb.50-60 degr.cels.The original "cristec" charger 50A,get cookt! Sekond wan a 60A" cristec" the same story,the garanty das not acsept, the repair! Last year I bot a 60A
"victron energy",work well.The multi volt/smart charger is very clever thing,( Reya ) posible? My englich is not gut, but I hope you understand?
Iv Pepe SM 223

--- El vie, 15/5/09, William Klein <sidecar1@verizon.net> escribió:


De: William Klein <sidecar1@verizon.net>
Asunto: Re: [Amel] 90-260 volt 50-60 cycle chargers
Para: amelyachtowners@yahoogroups.com
Fecha: viernes, 15 mayo, 2009 5:58








I beleive that you will find Xantrex makes chargers that do the same and they are available at West Marine. I put one in my Maramu and it worked fine. It could be programmed for multiple banks of different battery types and was available in 30A or 50A models.-- Bill Klein

----- Original Message -----
From: Richard Piller
To: amelyachtowners@ yahoogroups. com
Sent: Thursday, May 14, 2009 7:23 PM
Subject: Re: [Amel] 90-260 volt 50-60 cycle chargers

The multi volt/cycle chargers are sold in the US by Dolphin in FL. They are sold in France by Reya. When we are now in NH when we get back to the boat in a week or so we'll post the exact addresses.
Richard and Joan on Challenge SM 209

--- On Thu, 5/14/09, Iv Pepe <iv_pepe@yahoo. com> wrote:

From: Iv Pepe <iv_pepe@yahoo. com>
Subject: Re: [Amel] Iridium Sat Phone Antenna Installation
To: amelyachtowners@ yahoogroups. com
Date: Thursday, May 14, 2009, 4:08 AM

HI,

How can I get, a REY charger?

Iv Pepe SM,223

--- El mié, 13/5/09, Richard Piller <richard03801@ yahoo.com> escribió:

De: Richard Piller <richard03801@ yahoo.com>

Asunto: Re: [Amel] Iridium Sat Phone Antenna Installation

Para: amelyachtowners@ yahoogroups. com

Fecha: miércoles, 13 mayo, 2009 11:38

We mounted ours on the aft rail next to the outboard motor. It works well there and is protected by the motor.

Richard and Joan on Challenge in Annapolis SM 209

--- On Sun, 4/5/09, sv_seabbatical <sv.lonestar@ gmail.com> wrote:

From: sv_seabbatical <sv.lonestar@ gmail.com>

Subject: [Amel] Iridium Sat Phone Antenna Installation

To: amelyachtowners@ yahoogroups. com

Date: Sunday, April 5, 2009, 1:30 PM

I have an Iridium Sat Phone and want to know what kind of antenna installations have been done on Amel 54's. Are they all on the top of the mizzen? Has anyone mounted one on the dodger? All comments will be appreciated.

Craig Scott

LONE STAR

Amel 54 #101

[Non-text portions of this message have been removed]

[Non-text portions of this message have been removed]



[Non-text portions of this message have been removed]



















[Non-text portions of this message have been removed]


Re: [Amel] 90-260 volt 50-60 cycle chargers

William Klein <sidecar1@...>
 

I beleive that you will find Xantrex makes chargers that do the same and they are available at West Marine. I put one in my Maramu and it worked fine. It could be programmed for multiple banks of different battery types and was available in 30A or 50A models.-- Bill Klein

----- Original Message -----
From: Richard Piller
To: amelyachtowners@yahoogroups.com
Sent: Thursday, May 14, 2009 7:23 PM
Subject: Re: [Amel] 90-260 volt 50-60 cycle chargers





The multi volt/cycle chargers are sold in the US by Dolphin in FL. They are sold in France by Reya. When we are now in NH when we get back to the boat in a week or so we'll post the exact addresses.
Richard and Joan on Challenge SM 209

--- On Thu, 5/14/09, Iv Pepe <iv_pepe@yahoo.com> wrote:

From: Iv Pepe <iv_pepe@yahoo.com>
Subject: Re: [Amel] Iridium Sat Phone Antenna Installation
To: amelyachtowners@yahoogroups.com
Date: Thursday, May 14, 2009, 4:08 AM

HI,

How can I get, a REY charger?

Iv Pepe SM,223

--- El mié, 13/5/09, Richard Piller <richard03801@ yahoo.com> escribió:

De: Richard Piller <richard03801@ yahoo.com>

Asunto: Re: [Amel] Iridium Sat Phone Antenna Installation

Para: amelyachtowners@ yahoogroups. com

Fecha: miércoles, 13 mayo, 2009 11:38

We mounted ours on the aft rail next to the outboard motor. It works well there and is protected by the motor.

Richard and Joan on Challenge in Annapolis SM 209

--- On Sun, 4/5/09, sv_seabbatical <sv.lonestar@ gmail.com> wrote:

From: sv_seabbatical <sv.lonestar@ gmail.com>

Subject: [Amel] Iridium Sat Phone Antenna Installation

To: amelyachtowners@ yahoogroups. com

Date: Sunday, April 5, 2009, 1:30 PM

I have an Iridium Sat Phone and want to know what kind of antenna installations have been done on Amel 54's. Are they all on the top of the mizzen? Has anyone mounted one on the dodger? All comments will be appreciated.

Craig Scott

LONE STAR

Amel 54 #101

[Non-text portions of this message have been removed]













[Non-text portions of this message have been removed]





[Non-text portions of this message have been removed]


Re: [Amel] Anyone need traveler car for Maramu with Goiot 164 track?

Iv Pepe <iv_pepe@...>
 

Hi,
Sorry,west and budget marine have only T traweler. You will vind full produkt of GOIOT in NAVIMO USA (open web page) tel ( toll free) 866 383 1888 ,I hope its halp you.
Iv Pepe SM 223
--- El jue, 14/5/09, Dave Benjamin <dave_benjamin@yahoo.com> escribió:


De: Dave Benjamin <dave_benjamin@yahoo.com>
Asunto: Re: [Amel] Anyone need traveler car for Maramu with Goiot 164 track?
Para: amelyachtowners@yahoogroups.com
Fecha: jueves, 14 mayo, 2009 3:27








I just checked West Marine. Do you have any WM part numbers. Nothing in their catalog that remotely looks like it will fit Goiot "Y-track". This is for traveler track, not genoa fairlead.

--- On Thu, 5/14/09, Iv Pepe <iv_pepe@yahoo. com> wrote:

From: Iv Pepe <iv_pepe@yahoo. com>
Subject: Re: [Amel] Anyone need traveler car for Maramu with Goiot 164 track?
To: amelyachtowners@ yahoogroups. com
Date: Thursday, May 14, 2009, 1:00 AM

Hi,

All parts from GOJOT France you can find in West Marine,traweler car stopers.

Iv Pepe SM 223

--- El mié, 13/5/09, Dave_Benjamin <dave_benjamin@ yahoo.com> escribió:

De: Dave_Benjamin <dave_benjamin@ yahoo.com>

Asunto: [Amel] Anyone need traveler car for Maramu with Goiot 164 track?

Para: amelyachtowners@ yahoogroups. com

Fecha: miércoles, 13 mayo, 2009 6:16

I am ordering a traveler car from France for delivery here in the US. If anyone else wants to replace a car, end stops, etc. let me know. We can split shipping. I can email you diagrams of the cars and tracks. Plan to order in the next day or two.

[Non-text portions of this message have been removed]































[Non-text portions of this message have been removed]


Re: [Amel] Anyone need traveler car for Maramu with Goiot 164 track?

Richard Piller <richard03801@...>
 

If you can find a Goiot catalog in your local West Marine store good luck...
We got ours when we had our Maramu from I guy in MA that I don't think is still in business.  Best is to get it from Amel.  Goiot is very very hard to get anything from here in the US.
Richard and Joan on SM 209

--- On Thu, 5/14/09, Dave Benjamin <dave_benjamin@yahoo.com> wrote:

From: Dave Benjamin <dave_benjamin@yahoo.com>
Subject: Re: [Amel] Anyone need traveler car for Maramu with Goiot 164 track?
To: amelyachtowners@yahoogroups.com
Date: Thursday, May 14, 2009, 3:27 PM

















I just checked West Marine. Do you have any WM part numbers. Nothing in their catalog that remotely looks like it will fit Goiot "Y-track". This is for traveler track, not genoa fairlead.



--- On Thu, 5/14/09, Iv Pepe <iv_pepe@yahoo. com> wrote:



From: Iv Pepe <iv_pepe@yahoo. com>

Subject: Re: [Amel] Anyone need traveler car for Maramu with Goiot 164 track?

To: amelyachtowners@ yahoogroups. com

Date: Thursday, May 14, 2009, 1:00 AM



Hi,



All parts from GOJOT France you can find in West Marine,traweler car stopers.



Iv Pepe SM 223



--- El mié, 13/5/09, Dave_Benjamin <dave_benjamin@ yahoo.com> escribió:



De: Dave_Benjamin <dave_benjamin@ yahoo.com>



Asunto: [Amel] Anyone need traveler car for Maramu with Goiot 164 track?



Para: amelyachtowners@ yahoogroups. com



Fecha: miércoles, 13 mayo, 2009 6:16



I am ordering a traveler car from France for delivery here in the US. If anyone else wants to replace a car, end stops, etc. let me know. We can split shipping. I can email you diagrams of the cars and tracks. Plan to order in the next day or two.



[Non-text portions of this message have been removed]























[Non-text portions of this message have been removed]































[Non-text portions of this message have been removed]


Re: [Amel] Iridium Sat Phone Antenna Installation

Richard Piller <richard03801@...>
 

I will send a photo when we get back to the boat in a week or so.
Richard and Joan on SM 209

--- On Thu, 5/14/09, Uhlir János <ujanos@t-online.hu> wrote:

From: Uhlir János <ujanos@t-online.hu>
Subject: RE: [Amel] Iridium Sat Phone Antenna Installation
To: amelyachtowners@yahoogroups.com
Date: Thursday, May 14, 2009, 2:07 AM

Hi

Can we have a picture ?

Intresting !



J



  _____ 

From: amelyachtowners@yahoogroups.com
[mailto:amelyachtowners@yahoogroups.com] On Behalf Of Richard Piller
Sent: Wednesday, May 13, 2009 5:39 PM
To: amelyachtowners@yahoogroups.com
Subject: Re: [Amel] Iridium Sat Phone Antenna Installation








We mounted ours on the aft rail next to the outboard motor.  It works well
there and is protected by the motor.
Richard and Joan on Challenge in Annapolis SM 209

--- On Sun, 4/5/09, sv_seabbatical <sv.lonestar@
<mailto:sv.lonestar%40gmail.com> gmail.com> wrote:

From: sv_seabbatical <sv.lonestar@ <mailto:sv.lonestar%40gmail.com>
gmail.com>
Subject: [Amel] Iridium Sat Phone Antenna Installation
To: amelyachtowners@ <mailto:amelyachtowners%40yahoogroups.com>
yahoogroups.com
Date: Sunday, April 5, 2009, 1:30 PM

I have an Iridium Sat Phone and want to know what kind of antenna
installations have been done on Amel 54's. Are they all on the top of the
mizzen? Has anyone mounted one on the dodger? All comments will be
appreciated.

Craig Scott

LONE STAR

Amel 54 #101















A bejövõ levélben az AVG nem talált vírust
Checked by AVG - www.avg.com
Version: 8.5.325 / Virus Database: 270.12.27/2112 - Release Date: 05/13/09
07:04:00








------------------------------------

Yahoo! Groups Links








[Non-text portions of this message have been removed]


Re: [Amel] 90-260 volt 50-60 cycle chargers

Richard Piller <richard03801@...>
 

The multi volt/cycle chargers are sold in the US by Dolphin in FL. They are sold in France by Reya.  When we are now in NH when we get back to the boat in a week or so we'll post the exact addresses.
Richard and Joan on Challenge SM 209

--- On Thu, 5/14/09, Iv Pepe <iv_pepe@yahoo.com> wrote:

From: Iv Pepe <iv_pepe@yahoo.com>
Subject: Re: [Amel] Iridium Sat Phone Antenna Installation
To: amelyachtowners@yahoogroups.com
Date: Thursday, May 14, 2009, 4:08 AM

















HI,

How can I get, a REY charger?

Iv Pepe SM,223

--- El mié, 13/5/09, Richard Piller <richard03801@ yahoo.com> escribió:



De: Richard Piller <richard03801@ yahoo.com>

Asunto: Re: [Amel] Iridium Sat Phone Antenna Installation

Para: amelyachtowners@ yahoogroups. com

Fecha: miércoles, 13 mayo, 2009 11:38



We mounted ours on the aft rail next to the outboard motor.  It works well there and is protected by the motor.

Richard and Joan on Challenge in Annapolis SM 209



--- On Sun, 4/5/09, sv_seabbatical <sv.lonestar@ gmail.com> wrote:



From: sv_seabbatical <sv.lonestar@ gmail.com>

Subject: [Amel] Iridium Sat Phone Antenna Installation

To: amelyachtowners@ yahoogroups. com

Date: Sunday, April 5, 2009, 1:30 PM



I have an Iridium Sat Phone and want to know what kind of antenna installations have been done on Amel 54's. Are they all on the top of the mizzen? Has anyone mounted one on the dodger? All comments will be appreciated.



Craig Scott



LONE STAR



Amel 54 #101



[Non-text portions of this message have been removed]



































[Non-text portions of this message have been removed]


Re: [Amel] Amel Super Maramu Hull # 317 Papa - Papa II - Lady Divina

Dave_Benjamin
 

The brokerage that has her listed is reputable. I'm sure they are not trying to hide the damage history. There is no obligation for them to post it in the listing as long as it gets disclosed to potential buyers who inquire.

--- On Thu, 5/14/09, assistanttoblackdog <assistanttoblackdog@yahoo.com> wrote:

From: assistanttoblackdog <assistanttoblackdog@yahoo.com>
Subject: [Amel] Amel Super Maramu Hull # 317 Papa - Papa II - Lady Divina
To: amelyachtowners@yahoogroups.com
Date: Thursday, May 14, 2009, 12:48 PM

















I noticed that Amel Super Maramu hull # 317 Papa II is listed for sale on yachtworld dot com, lying in Seattle.



I didn't see any history of multiple severe damage incidents mentioned in the broker's listing, thus I felt it my duty to post this.



It is my understanding that some of the history of Amel Super Maramu 2000 hull # 317 is as follows:



The boat was previously known as Lady Divina. She boat was blown off of her stands while on the hard in Venezuela by hurricane Ivan in 2004. A hole was punched completely through the hull and the nav station area and bulkhead underwent extensive repairs.



The boat was then put up for sale and after a long time on the market she was purchased by a new owner at a substantial discount.



On July 6, 2007 while in British Columbia, Canada the new owner ran her into the rocks under full power at 8 knots causing the keel to be completely ripped off, separated from the hull and lost.



In post #'s 2998 and 2999 on this Yahoo group the owner wrote:



"Well the bow thruster prop repair is way down on the list today.

Yesterday PAPA struck a rock HARD at 8 knots in Canada and LOST HER

KEEL. She floated free after it got ripped off in about 10 minutes

of twisting and rolling with the surging currents. I was able to

motor slowly away to deeper water and dive over to see the keel was

GONE. At high RPM's there was severe vibrations so I took the FREE

(CANADA COAST GUARD IS AWESOME) tow to Port Hardy, BC where I will be

spending some time exploring the construction of the AMELS...



Once out of the water you can see all the stainless keel bolts were

cut clean off. The transmission housing is sagging down 4 inches

(but the prop turns fine and was able to motor slowly into the

haulout slip.) There is fresh water leaking out from the bottom of

what is left of the keel, so I will be drinking large quanities of

good Canadian Beer.



If anyone has any experience with reattaching a keel, water tank

repair or transmission issues, I am all ears."



And finally, two months later while awaiting repairs the owner was killed on October 18, 2007 in a tragic kite surfing accident in Seattle. ( www dot sailpapa dot com )



If anyone believes any of this information is in error please notify me and I will immediately post a correction.



Just thought you might want to know – I would if I were in the market.



Best,



Jim

former SM & future Amel owner




























[Non-text portions of this message have been removed]


Amel Super Maramu Hull # 317 Papa - Papa II - Lady Divina

assistanttoblackdog <assistanttoblackdog@...>
 

I noticed that Amel Super Maramu hull # 317 Papa II is listed for sale on yachtworld dot com, lying in Seattle.

I didn't see any history of multiple severe damage incidents mentioned in the broker's listing, thus I felt it my duty to post this.

It is my understanding that some of the history of Amel Super Maramu 2000 hull # 317 is as follows:

The boat was previously known as Lady Divina. She boat was blown off of her stands while on the hard in Venezuela by hurricane Ivan in 2004. A hole was punched completely through the hull and the nav station area and bulkhead underwent extensive repairs.

The boat was then put up for sale and after a long time on the market she was purchased by a new owner at a substantial discount.

On July 6, 2007 while in British Columbia, Canada the new owner ran her into the rocks under full power at 8 knots causing the keel to be completely ripped off, separated from the hull and lost.

In post #'s 2998 and 2999 on this Yahoo group the owner wrote:

"Well the bow thruster prop repair is way down on the list today.
Yesterday PAPA struck a rock HARD at 8 knots in Canada and LOST HER
KEEL. She floated free after it got ripped off in about 10 minutes
of twisting and rolling with the surging currents. I was able to
motor slowly away to deeper water and dive over to see the keel was
GONE. At high RPM's there was severe vibrations so I took the FREE
(CANADA COAST GUARD IS AWESOME) tow to Port Hardy, BC where I will be
spending some time exploring the construction of the AMELS...

Once out of the water you can see all the stainless keel bolts were
cut clean off. The transmission housing is sagging down 4 inches
(but the prop turns fine and was able to motor slowly into the
haulout slip.) There is fresh water leaking out from the bottom of
what is left of the keel, so I will be drinking large quanities of
good Canadian Beer.

If anyone has any experience with reattaching a keel, water tank
repair or transmission issues, I am all ears."


And finally, two months later while awaiting repairs the owner was killed on October 18, 2007 in a tragic kite surfing accident in Seattle. ( www dot sailpapa dot com )

If anyone believes any of this information is in error please notify me and I will immediately post a correction.

Just thought you might want to know – I would if I were in the market.

Best,

Jim
former SM & future Amel owner