Date   
Re: [Amel Yacht Owners] Bow Thruster Anomaly

Thomas Peacock
 

Thanks to all for such speedy replies. 
But no, despite the photo appearance, what you see are not two neoprene seals. The top of the structure is rock hard. 
Assuming no one else has a similar appearance, I'm afraid that Admiral Bill is right. We bought her about 8 years ago, that topmost area was always rock solid. Either fiberglass, or some material that is poured into mast fittings to seal them. 
I suspect previous owner had a little bit of water coming in and took it to a boatyard. Their solution was to raise the apparent waterline by an inch or so. 
It looks like it will be a bear to get off. 
If anyone else has any thoughts, please fire away, always appreciated. 
Tom Peacock
SM 240 Aletes
Rock Hall, Maryland


On Aug 31, 2017, at 6:26 PM, kimberlite@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hi Tom,
the photo shows 2 foam seals . These are attached with contact cement. Below this is the lip seal that you are looking for. The lisp seal is installed with silicone sealant.The foam and lip seals need to be changed.
Fair Winds,
Eric
sm 376
 


----- Original Message -----
From: "John Clark john.biohead@... [amelyachtowners]"
Date: Thursday, August 31, 2017 5:55 pm
Subject: Re: [Amel Yacht Owners] Bow Thruster Anomaly
To: amelyachtowners@...

> Thomas, my BT looks similar. I have a foam disk that feels
> glued to an
> epoxy bed. No screws evident, also no leakage.
>
> My BT is an older model...form 1990. Not sure when they updated it.
>
> John
> SV Annie. SM 37
> Pamlico Sound.
>
> On Aug 31, 2017 5:42 PM, "Thomas Peacock peacock8491@...
> [amelyachtowners]" wrote:
>
> >
> > [Attachment(s) <#m_6356709092296176804_TopText> from Thomas Peacock
> > included below]
> >
> > Trying to get the pic to send.
> >
> > [image: image1.jpeg]
> >
> >
> > On Aug 31, 2017, at 5:10 PM, peacock8491@...
> [amelyachtowners] <
> > amelyachtowners@...> wrote:
> >
> >
> >
> > Hi all,
> >
> > We are hauled out for C-Drive and bottom paint.
> >
> > We are trying to change the seal in the bow thruster trunk. It
> has not
> > been changed for at least 8 years, and we do get quite a bit
> of water
> > coming in while at sea.
> >
> > All the pictures that I have seen in this group show a seal
> held in by two
> > screws with washers. However, ours seems a bit different, see
> pic below.
> > There is at least two centimeters of further hard casing above
> the seal. It
> > seems to be integral to the entire setup. We are not able to
> see any
> > screws, and hence are unable to change the seal.
> >
> > Any thoughts would be appreciated. We splash back in the water
> around 1300
> > hours GMT on Friday, and would really like to change the seal.
> Sorry for
> > the klunky picture.
> >
> > Tom Peacock
> >
> > SM 240 Aletes
> >
> > Rock Hall, Maryland
> >
> >
> >
> >
> >
> >
>

Re: [Amel Yacht Owners] Colombia

Stephen Davis
 

We are similar to JP, but will transit the canal sometime in January, and head for the Marquesas the 2nd week of March. We are still considering going via Easter Island, Pitcairn, and the Gambiers in which case we would leave earlier. 

Aloha,
Steve 

On Aug 31, 2017, at 11:30, Germain Jean-Pierre jgermain@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hi Kent,


For me, its Aruba, Columbia, Panama (San Blas & Boca del Toro) then the canal to Galapagos, Marquesas etc…

Passage to Pacific is planned in first 1/3 of Jan 18.

:-)

Regards,

Jean-Pierre
Eleuthera, SM 007


On 31 Aug 2017, at 22:24, Kent Robertson karkauai@... [amelyachtowners] <amelyachtowners@...> wrote:

 

When my girlfriend retires, hopefully in the next year.  We'll spend some time in Belize b4 we transit the canal.  Are you headed that way too?

Kent
S/V Kristy
SM243


Re: [Amel Yacht Owners] Bow Thruster Anomaly

Alexandre Uster von Baar
 

Hello Tom,

I am sure you know about the illustration
http://nikimat.com/bow_thruster_overhaul.html

I always agree with Bill (R) on keeping as original the boat as you can…

Sincerely, Alexandre
SM2K #289 NIKIMAT
IGY Simpson Bay Marina, St Maarten, NA




--------------------------------------------

On Thu, 8/31/17, 'Bill & Judy Rouse' yahoogroups@... [amelyachtowners] <amelyachtowners@...> wrote:

Subject: Re: [Amel Yacht Owners] Bow Thruster Anomaly
To: "amelyachtowners@..." <amelyachtowners@...>
Date: Thursday, August 31, 2017, 4:51 PM


 









Tom,
My first thought is
that you have had a "de-Ameling" modification by
previous owner(s)...I think it is serious and needs to be
addressed. There are plenty of photos of how it should
be. 
From the view you
posted we should see 1 neoprene donut seal that has been
contact-cemented over a lip seal which is normally held down
by a screw with a washer. The lip seal and the top side
donut I spoke of earlier seal the outside water from coming
into the boat when the bow thruster is DOWN. There are also
2 neoprene donut seals contact cemented to the top of the
bow thruster foot...these two seal the outside water from
coming into the boat when the bow thruster is UP with its
safety pin engaged. It is a simple and reliable
system.
It really disturbs
me when I see someone try to outsmart this Amel design...I
know that was not you.
Good
luck.
Best,
CW Bill Rouse
Admiral, Texas Navy
Commander
Emeritus
Amel
School  http://www.amelschool.
com
720 Winnie
St
Galveston Island, TX
77550
+1(832)
380-4970



On Thu, Aug 31, 2017 at
4:10 PM, peacock8491@...
[amelyachtowners] <amelyachtowners@...>
wrote:















 









Hi all,We are
hauled out for C-Drive and bottom
paint. We are trying to change the seal
in the bow thruster trunk. It has not been changed for at
least 8 years, and we do get quite a bit of water coming in
while at sea. All the pictures that I
have seen in this group show a seal held in by two screws
with washers. However, ours seems a bit different, see pic
below. There is at least two centimeters of further hard
casing above the seal. It seems to be integral to the entire
setup. We are not able to see any screws, and hence are
unable to change the
seal. Any thoughts
would be appreciated. We splash back in the water around
1300 hours GMT on Friday, and would really like to change
the seal. Sorry for the klunky
picture. Tom
PeacockSM 240
AletesRock Hall,
Maryland


































#yiv3501365646 #yiv3501365646 --
#yiv3501365646ygrp-mkp {
border:1px solid #d8d8d8;font-family:Arial;margin:10px
0;padding:0 10px;}

#yiv3501365646 #yiv3501365646ygrp-mkp hr {
border:1px solid #d8d8d8;}

#yiv3501365646 #yiv3501365646ygrp-mkp #yiv3501365646hd {
color:#628c2a;font-size:85%;font-weight:700;line-height:122%;margin:10px
0;}

#yiv3501365646 #yiv3501365646ygrp-mkp #yiv3501365646ads {
margin-bottom:10px;}

#yiv3501365646 #yiv3501365646ygrp-mkp .yiv3501365646ad {
padding:0 0;}

#yiv3501365646 #yiv3501365646ygrp-mkp .yiv3501365646ad p {
margin:0;}

#yiv3501365646 #yiv3501365646ygrp-mkp .yiv3501365646ad a {
color:#0000ff;text-decoration:none;}
#yiv3501365646 #yiv3501365646ygrp-sponsor
#yiv3501365646ygrp-lc {
font-family:Arial;}

#yiv3501365646 #yiv3501365646ygrp-sponsor
#yiv3501365646ygrp-lc #yiv3501365646hd {
margin:10px
0px;font-weight:700;font-size:78%;line-height:122%;}

#yiv3501365646 #yiv3501365646ygrp-sponsor
#yiv3501365646ygrp-lc .yiv3501365646ad {
margin-bottom:10px;padding:0 0;}

#yiv3501365646 #yiv3501365646actions {
font-family:Verdana;font-size:11px;padding:10px 0;}

#yiv3501365646 #yiv3501365646activity {
background-color:#e0ecee;float:left;font-family:Verdana;font-size:10px;padding:10px;}

#yiv3501365646 #yiv3501365646activity span {
font-weight:700;}

#yiv3501365646 #yiv3501365646activity span:first-child {
text-transform:uppercase;}

#yiv3501365646 #yiv3501365646activity span a {
color:#5085b6;text-decoration:none;}

#yiv3501365646 #yiv3501365646activity span span {
color:#ff7900;}

#yiv3501365646 #yiv3501365646activity span
.yiv3501365646underline {
text-decoration:underline;}

#yiv3501365646 .yiv3501365646attach {
clear:both;display:table;font-family:Arial;font-size:12px;padding:10px
0;width:400px;}

#yiv3501365646 .yiv3501365646attach div a {
text-decoration:none;}

#yiv3501365646 .yiv3501365646attach img {
border:none;padding-right:5px;}

#yiv3501365646 .yiv3501365646attach label {
display:block;margin-bottom:5px;}

#yiv3501365646 .yiv3501365646attach label a {
text-decoration:none;}

#yiv3501365646 blockquote {
margin:0 0 0 4px;}

#yiv3501365646 .yiv3501365646bold {
font-family:Arial;font-size:13px;font-weight:700;}

#yiv3501365646 .yiv3501365646bold a {
text-decoration:none;}

#yiv3501365646 dd.yiv3501365646last p a {
font-family:Verdana;font-weight:700;}

#yiv3501365646 dd.yiv3501365646last p span {
margin-right:10px;font-family:Verdana;font-weight:700;}

#yiv3501365646 dd.yiv3501365646last p
span.yiv3501365646yshortcuts {
margin-right:0;}

#yiv3501365646 div.yiv3501365646attach-table div div a {
text-decoration:none;}

#yiv3501365646 div.yiv3501365646attach-table {
width:400px;}

#yiv3501365646 div.yiv3501365646file-title a, #yiv3501365646
div.yiv3501365646file-title a:active, #yiv3501365646
div.yiv3501365646file-title a:hover, #yiv3501365646
div.yiv3501365646file-title a:visited {
text-decoration:none;}

#yiv3501365646 div.yiv3501365646photo-title a,
#yiv3501365646 div.yiv3501365646photo-title a:active,
#yiv3501365646 div.yiv3501365646photo-title a:hover,
#yiv3501365646 div.yiv3501365646photo-title a:visited {
text-decoration:none;}

#yiv3501365646 div#yiv3501365646ygrp-mlmsg
#yiv3501365646ygrp-msg p a span.yiv3501365646yshortcuts {
font-family:Verdana;font-size:10px;font-weight:normal;}

#yiv3501365646 .yiv3501365646green {
color:#628c2a;}

#yiv3501365646 .yiv3501365646MsoNormal {
margin:0 0 0 0;}

#yiv3501365646 o {
font-size:0;}

#yiv3501365646 #yiv3501365646photos div {
float:left;width:72px;}

#yiv3501365646 #yiv3501365646photos div div {
border:1px solid
#666666;min-height:62px;overflow:hidden;width:62px;}

#yiv3501365646 #yiv3501365646photos div label {
color:#666666;font-size:10px;overflow:hidden;text-align:center;white-space:nowrap;width:64px;}

#yiv3501365646 #yiv3501365646reco-category {
font-size:77%;}

#yiv3501365646 #yiv3501365646reco-desc {
font-size:77%;}

#yiv3501365646 .yiv3501365646replbq {
margin:4px;}

#yiv3501365646 #yiv3501365646ygrp-actbar div a:first-child {
margin-right:2px;padding-right:5px;}

#yiv3501365646 #yiv3501365646ygrp-mlmsg {
font-size:13px;font-family:Arial, helvetica, clean,
sans-serif;}

#yiv3501365646 #yiv3501365646ygrp-mlmsg table {
font-size:inherit;font:100%;}

#yiv3501365646 #yiv3501365646ygrp-mlmsg select,
#yiv3501365646 input, #yiv3501365646 textarea {
font:99% Arial, Helvetica, clean, sans-serif;}

#yiv3501365646 #yiv3501365646ygrp-mlmsg pre, #yiv3501365646
code {
font:115% monospace;}

#yiv3501365646 #yiv3501365646ygrp-mlmsg * {
line-height:1.22em;}

#yiv3501365646 #yiv3501365646ygrp-mlmsg #yiv3501365646logo {
padding-bottom:10px;}


#yiv3501365646 #yiv3501365646ygrp-msg p a {
font-family:Verdana;}

#yiv3501365646 #yiv3501365646ygrp-msg
p#yiv3501365646attach-count span {
color:#1E66AE;font-weight:700;}

#yiv3501365646 #yiv3501365646ygrp-reco
#yiv3501365646reco-head {
color:#ff7900;font-weight:700;}

#yiv3501365646 #yiv3501365646ygrp-reco {
margin-bottom:20px;padding:0px;}

#yiv3501365646 #yiv3501365646ygrp-sponsor #yiv3501365646ov
li a {
font-size:130%;text-decoration:none;}

#yiv3501365646 #yiv3501365646ygrp-sponsor #yiv3501365646ov
li {
font-size:77%;list-style-type:square;padding:6px 0;}

#yiv3501365646 #yiv3501365646ygrp-sponsor #yiv3501365646ov
ul {
margin:0;padding:0 0 0 8px;}

#yiv3501365646 #yiv3501365646ygrp-text {
font-family:Georgia;}

#yiv3501365646 #yiv3501365646ygrp-text p {
margin:0 0 1em 0;}

#yiv3501365646 #yiv3501365646ygrp-text tt {
font-size:120%;}

#yiv3501365646 #yiv3501365646ygrp-vital ul li:last-child {
border-right:none !important;
}
#yiv3501365646

How to attach a photo

eric freedman
 

Re: [Amel Yacht Owners] Bow Thruster Anomaly

eric freedman
 

Re: [Amel Yacht Owners] Bow Thruster Anomaly

Bill & Judy Rouse <yahoogroups@...>
 

John,

Read my earlier reply...

The screw and washer, if it has one, would be under the single foam donut which should be contact-cemented in place over the lip seal. The screw and washer, if it has one, holds the lip seal in place,

The reason I say if it has one, is I have seen Amel SMs without this screw and washer, and with no hole. I am not sure why because I believe that you would want to make sure that when the tube is raising that it does not pull the seal up with it.

There are plenty of photos in the Photo section and there are procedures in the Files section.

Best,

CW Bill Rouse
Admiral, Texas Navy
Commander Emeritus

Amel School  http://www.amelschool.com
720 Winnie St
Galveston Island, TX 77550

+1(832) 380-4970






On Thu, Aug 31, 2017 at 4:55 PM, John Clark john.biohead@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Thomas, my BT looks similar.  I have a foam disk that feels glued to an epoxy bed.  No screws evident,  also no leakage.

My BT is an older model...form 1990.  Not sure when they updated it.

John
SV Annie. SM 37
Pamlico Sound.

On Aug 31, 2017 5:42 PM, "Thomas Peacock peacock8491@... [amelyachtowners]" <amelyachtowners@yahoogroups.com> wrote:
 
[Attachment(s) from Thomas Peacock included below]

Trying to get the pic to send.



On Aug 31, 2017, at 5:10 PM, peacock8491@... [amelyachtowners] <amelyachtowners@...om> wrote:

 

Hi all,

We are hauled out for C-Drive and bottom paint. 

We are trying to change the seal in the bow thruster trunk. It has not been changed for at least 8 years, and we do get quite a bit of water coming in while at sea. 

All the pictures that I have seen in this group show a seal held in by two screws with washers. However, ours seems a bit different, see pic below. There is at least two centimeters of further hard casing above the seal. It seems to be integral to the entire setup. We are not able to see any screws, and hence are unable to change the seal. 

Any thoughts would be appreciated. We splash back in the water around 1300 hours GMT on Friday, and would really like to change the seal. Sorry for the klunky picture. 

Tom Peacock

SM 240 Aletes

Rock Hall, Maryland





Re: [Amel Yacht Owners] Bow Thruster Anomaly [1 Attachment]

John Clark
 

Thomas, my BT looks similar.  I have a foam disk that feels glued to an epoxy bed.  No screws evident,  also no leakage.

My BT is an older model...form 1990.  Not sure when they updated it.

John
SV Annie. SM 37
Pamlico Sound.

On Aug 31, 2017 5:42 PM, "Thomas Peacock peacock8491@... [amelyachtowners]" <amelyachtowners@...> wrote:
 
[Attachment(s) from Thomas Peacock included below]

Trying to get the pic to send.



On Aug 31, 2017, at 5:10 PM, peacock8491@... [amelyachtowners] <amelyachtowners@yahoogroups.com> wrote:

 

Hi all,

We are hauled out for C-Drive and bottom paint. 

We are trying to change the seal in the bow thruster trunk. It has not been changed for at least 8 years, and we do get quite a bit of water coming in while at sea. 

All the pictures that I have seen in this group show a seal held in by two screws with washers. However, ours seems a bit different, see pic below. There is at least two centimeters of further hard casing above the seal. It seems to be integral to the entire setup. We are not able to see any screws, and hence are unable to change the seal. 

Any thoughts would be appreciated. We splash back in the water around 1300 hours GMT on Friday, and would really like to change the seal. Sorry for the klunky picture. 

Tom Peacock

SM 240 Aletes

Rock Hall, Maryland




Re: [Amel Yacht Owners] Bow Thruster Anomaly

Bill & Judy Rouse <yahoogroups@...>
 

Tom,

My first thought is that you have had a "de-Ameling" modification by previous owner(s)...I think it is serious and needs to be addressed. There are plenty of photos of how it should be. 

From the view you posted we should see 1 neoprene donut seal that has been contact-cemented over a lip seal which is normally held down by a screw with a washer. The lip seal and the top side donut I spoke of earlier seal the outside water from coming into the boat when the bow thruster is DOWN. There are also 2 neoprene donut seals contact cemented to the top of the bow thruster foot...these two seal the outside water from coming into the boat when the bow thruster is UP with its safety pin engaged. It is a simple and reliable system.

It really disturbs me when I see someone try to outsmart this Amel design...I know that was not you.

Good luck.

Best,

CW Bill Rouse
Admiral, Texas Navy
Commander Emeritus

Amel School  http://www.amelschool.com
720 Winnie St
Galveston Island, TX 77550

+1(832) 380-4970




On Thu, Aug 31, 2017 at 4:10 PM, peacock8491@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Hi all,

We are hauled out for C-Drive and bottom paint. 

We are trying to change the seal in the bow thruster trunk. It has not been changed for at least 8 years, and we do get quite a bit of water coming in while at sea. 

All the pictures that I have seen in this group show a seal held in by two screws with washers. However, ours seems a bit different, see pic below. There is at least two centimeters of further hard casing above the seal. It seems to be integral to the entire setup. We are not able to see any screws, and hence are unable to change the seal. 

Any thoughts would be appreciated. We splash back in the water around 1300 hours GMT on Friday, and would really like to change the seal. Sorry for the klunky picture. 

Tom Peacock

SM 240 Aletes

Rock Hall, Maryland





Re: Bow Thruster Anomaly

Paul Osterberg
 

Tom
To me it looks as you have the neopren seals glued on top of the lip seal. We have one neoprene seals inside the hull just lose on the shaft, and two neoprene seals o the shaft below waterline. I do not think the lip seal that sometimes is fixed with the two screws and the washers do seal very much. The reason for my assumption is that when service the bow thruster in the water, one tape the shaft to seal from water penetrating into the shaft. The tape passes through the lip seal and thus do not seal very much. The important seals are the neoprene seals, two below waterline md one above the waterline.
We have no problem with water intrusion even when slamming hard into the waves in rough weather but we change the neoprene seals A year ago, and will probably change them bi annually 
Paul on SY Kerpa SM259'Block Island 

Re: [Amel Yacht Owners] Colombia

karkauai
 

Hola JP, I'll be a few months behind you.  Have fun!

Kent Robertson
S/V Kristy
SM243

Re: [Amel Yacht Owners] Colombia

Germain Jean-Pierre <jgermain@...>
 

Hi Kent,

For me, its Aruba, Columbia, Panama (San Blas & Boca del Toro) then the canal to Galapagos, Marquesas etc…

Passage to Pacific is planned in first 1/3 of Jan 18.

:-)

Regards,

Jean-Pierre
Eleuthera, SM 007


On 31 Aug 2017, at 22:24, Kent Robertson karkauai@... [amelyachtowners] <amelyachtowners@...> wrote:

 

When my girlfriend retires, hopefully in the next year.  We'll spend some time in Belize b4 we transit the canal.  Are you headed that way too?

Kent
S/V Kristy
SM243


Re: [Amel Yacht Owners] Colombia

karkauai
 

When my girlfriend retires, hopefully in the next year.  We'll spend some time in Belize b4 we transit the canal.  Are you headed that way too?

Kent
S/V Kristy
SM243

Re: Bow Thruster Anomaly

Thomas Peacock
 

Still trying to get pic. 

Re: [Amel Yacht Owners] Bow Thruster Anomaly

Thomas Peacock
 

Trying to get the pic to send.



On Aug 31, 2017, at 5:10 PM, peacock8491@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hi all,

We are hauled out for C-Drive and bottom paint. 

We are trying to change the seal in the bow thruster trunk. It has not been changed for at least 8 years, and we do get quite a bit of water coming in while at sea. 

All the pictures that I have seen in this group show a seal held in by two screws with washers. However, ours seems a bit different, see pic below. There is at least two centimeters of further hard casing above the seal. It seems to be integral to the entire setup. We are not able to see any screws, and hence are unable to change the seal. 

Any thoughts would be appreciated. We splash back in the water around 1300 hours GMT on Friday, and would really like to change the seal. Sorry for the klunky picture. 

Tom Peacock

SM 240 Aletes

Rock Hall, Maryland




Bow Thruster Anomaly

Thomas Peacock
 

Hi all,

We are hauled out for C-Drive and bottom paint. 

We are trying to change the seal in the bow thruster trunk. It has not been changed for at least 8 years, and we do get quite a bit of water coming in while at sea. 

All the pictures that I have seen in this group show a seal held in by two screws with washers. However, ours seems a bit different, see pic below. There is at least two centimeters of further hard casing above the seal. It seems to be integral to the entire setup. We are not able to see any screws, and hence are unable to change the seal. 

Any thoughts would be appreciated. We splash back in the water around 1300 hours GMT on Friday, and would really like to change the seal. Sorry for the klunky picture. 

Tom Peacock

SM 240 Aletes

Rock Hall, Maryland




Re: [Amel Yacht Owners] New old maramu !

smiles bernard
 

Many thanks for the warm welcome all!

We have hull 162 from 1985

Todd the galley changes you are making sound interesting. 

We are just back from a week sailing with the kids and are still at the 'wow' stage. It could well be a stage that  lasts a long long time :)

All the best
Miles



On 28 Aug 2017, at 11:57, John Clark john.biohead@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hi Miles,
   Congratulations and welcome.  The forum is a treasure trove of solid information that you will find invaluable.  

Regards,  John

John Clark
SV Annie SM 37
Hunkering down for TS Irma in Pamlico River.



On Aug 26, 2017 11:25 AM, "smiles bernard smilesbernard@... [amelyachtowners]" <amelyachtowners@...> wrote:
 

Hello there

I've posted a few times already but this week we are now aboard our new (to us) 1985 maramu 46

She is not a SM but is super to us 😉.

Our last long distance cruising boat was 30ft Halmatic so we are amazed by the comforts, the build quality and details - if a little overwhelmed by her size too!

We are planning an Atlantic circuit next year with our two young boys of 7 and 4 yrs.

It's great to have an amel and this active and helpful forum seems like a place I'll be often!

All the very best

Miles
SV 'Sea love'



Re: Battery power off levers do not cut all power

svperegrinus@yahoo.com
 

I believe in the original design, only the power to the radio memory or radio clock is supposed to be truly permanent.

My Fusion stereo has one (+) that is for "battery", i.e., a permanent connection.  This power input powers the clock inside the Fusion only, and this power input is incapable of powering up the Fusion itself.  Power is provided by the "permanent" DC-DC converter.

There is another (+) into the Fusion which is for "switched power", i.e., a switchable power connection.  This power input powers the balance of the stereo functions.  This power is supplied by a different DC-DC converter than the one that supplies the permanent connection.

I would not connect anything else to the permanent power supply.

Cheerio,

Peregrinus
SM2K N. 350 (2002)
At anchor, Neapolis (East Macedonia)

Re: [Amel Yacht Owners] Colombia

eric freedman
 

Re: [Amel Yacht Owners] Colombia

Stephen Davis
 

Thank Ken...we will definitely do that. When will you be heading back to Panama, and on to the Pacific?

Aloha,
Steve and Liz

On Aug 31, 2017, at 07:45, Kent Robertson karkauai@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Good to hear, Steve.  Be sure to stop at Portobelo for a day or two, and spend a night (not weekend) at Playa Blanca just East of Portobelo.  Quiet, beautiful anchorage with a decent snorkeling reef.  You can get in behind the reef

Kent
S/V Kristy
SM243

Re: Battery power off levers do not cut all power

eamonn.washington@...
 

Hi Tom

Thanks, I did not think of the radio presets.

In my case I think I will sacrifice radio presets for ease of cutting all power quickly.  I already switched my VHF and AIS transceiver to the Funk power switch.

Eamonn
Travel Bug SM 151
Currently in Greece