Date   

[Amel Yacht Owners] SM Keel bolts

eric freedman
 

Hi Ian,

I know there Is a drawing of the bonding strap is somewhere in the photos or possibly the files section of the Amel website.

 

I made mine out of a very thick wide piece of copper plate probably thicker than 1/8 of an inch.

To save a lot of soldering, I cut the top of the old bonding strap off and

soldered and bolted the old top of the plate, with wires attached, to the new strap. You need a torch to do this.

 

I do recall I used a 30 mm socket to remove the nut. However I do not remember the diameter of the bolt. It was at least 25 mm.

 

I used a large socket wrench with a number of extensions attached to remove and replace the nut. I taped the extensions together so they would not separate while working with the nut. Once the nut was removed I used a grabber tool to recover the nut.

 

It looks like this- https://www.homedepot.com/p/GrabEasy-Grabber-and-Retriever-PF0401/202505170.

You need a long one. It has come in handy over the years to recover other stuff dropped into the bilge.

 

To replace the nut I just put some masking tape over the edges of the nut and the socket. It was rather easy.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Saturday, March 31, 2018 1:06 PM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] SM Keel bolts

 

 

Hi Ian,

 

Just completed the job in Port Grimaud.

 

On hull 461 we required a 30mm “deep reach” socket to undo the keel bolt.

 

The hole in the copper strip we used was 2mm diameter.

 

We had our strip made up in UK for £120 including all the drilling, bending and delivery.

 

If you are in UK give me a call and I’ll talk you through our experience.  You should have our card somewhere.

 

Regards

 

Mike

 

Solitude

SM2K 461


On 31 Mar 2018, at 16:32, Ian & Judy ianjudyjenkins@... [amelyachtowners] <amelyachtowners@...> wrote:

 

 Hi all,

 

Does anyone know the diameter of the keel bolt in the grey water bilge in the engine room of an SM ? I am making up the copper strip that bolts on to the aft bolt but I'm not on board and don't know how big to make the hole on the copper strip.

 

     Ian and Judy,

 Pen Azen, SM 302, Preveza, Greece


Re: [Amel Yacht Owners] SM Keel bolts

Mike Johnson
 

Hi Ian,

Hole size should read 22mm

On 31 Mar 2018, at 18:05, Mike Johnson mike.k.johnson@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hi Ian,

Just completed the job in Port Grimaud.

On hull 461 we required a 30mm “deep reach” socket to undo the keel bolt.

The hole in the copper strip we used was 2mm diameter.

We had our strip made up in UK for £120 including all the drilling, bending and delivery.

If you are in UK give me a call and I’ll talk you through our experience.  You should have our card somewhere.

Regards

Mike

Solitude
SM2K 461

On 31 Mar 2018, at 16:32, Ian & Judy ianjudyjenkins@... [amelyachtowners] <amelyachtowners@...> wrote:

 

 Hi all,


Does anyone know the diameter of the keel bolt in the grey water bilge in the engine room of an SM ? I am making up the copper strip that bolts on to the aft bolt but I'm not on board and don't know how big to make the hole on the copper strip.


     Ian and Judy,

 Pen Azen, SM 302, Preveza, Greece


Re: [Amel Yacht Owners] SM Keel bolts

Mike Johnson
 

Hi Ian,

Just completed the job in Port Grimaud.

On hull 461 we required a 30mm “deep reach” socket to undo the keel bolt.

The hole in the copper strip we used was 2mm diameter.

We had our strip made up in UK for £120 including all the drilling, bending and delivery.

If you are in UK give me a call and I’ll talk you through our experience.  You should have our card somewhere.

Regards

Mike

Solitude
SM2K 461

On 31 Mar 2018, at 16:32, Ian & Judy ianjudyjenkins@... [amelyachtowners] <amelyachtowners@...> wrote:

 

 Hi all,


Does anyone know the diameter of the keel bolt in the grey water bilge in the engine room of an SM ? I am making up the copper strip that bolts on to the aft bolt but I'm not on board and don't know how big to make the hole on the copper strip.


     Ian and Judy,

 Pen Azen, SM 302, Preveza, Greece


where do you store your tools?

eric freedman
 

https://groups.yahoo.com/neo/groups/amelyachtowners/photos/albums/1140528980

 

I believe this is the absolute best way to store tools.

I also has Amel add a drawer under the lowest step. I use this for everyday tools.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

Hi all,

I'm wondering where you store all your tools.  I feel like most of us are very handy, so we must have a lot of them.  I use many of my tools on a near-daily basis, so I like to keep them easily accessible.  I've filled both of the drawers beneath the starboard settee, and I still have more tools that need homes!  Is there some awesome storage place I haven't thought of?  Where do you keep yours?

 

Thanks,

Ryan

SM 233 Iteration

Boston, MA, USA

 


Re: [Amel Yacht Owners] Rescueing method of casualty (Person Over Board)

Mike Johnson
 

Hi James,

I’m not a medical expert but this is the rational that was given to us.

The basic physiology is that anyone who has been in the water for a period of time has the blood in the lower limbs supported by the water and there is less blood in the lower half of the body.

When lifted vertically out of the water the blood the flows more rapidly to the lower limbs.  Therefore, blood pressure lowers rapidly and heightens the risk of cardiac arrest.

Hope this helps.

Regards

Mike & Peta

Solitude
SM2K 461

On 31 Mar 2018, at 17:17, James Studdart james.studdart@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Can anyone elaborate on why the RYA suggests people are lifted horizontally? I find that hard to believe. The idea of using two lines to lift a casualty out of the water fills me with dread of tangles, loops and over complication. Why double weight? Surely a wet person weighs the same vertical or horizontal.

Cheers,
James
SV SeaBean, SM344
Moorea

On Sat, Mar 31, 2018 at 00:22 Bill Rouse brouse@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Phillip,

I believe that the way the Super Maramu was designed, rigged, and equipped, it may be superior to any other sailboat regarding your rescue questions.

The mizzen mast was rigged with 2 each 10mm halyards (1 port and 1 stbd) each capable of lifting at least 1000 pounds. Each can be hauled using the electric main sheet winch. More importantly, there is a block for each at the end of the mizzen boom which will aid in holding the retrieved person off the boat. With the mizzen sheet loose, the end of the  mizzen boom will elevate when the halyard shackle meets the boom block, allowing you to swing the boom and person up and over the rail.

However, all above is based on how the Super Maramu was designed and built and may not be true with a particular Super Maramu owned by a non-caring owner, or a smarter person than Henri Amel.I hope this helps you. If you need more information, please contact me. 

Best,

CW Bill Rouse
Admiral, Texas Navy
Commander Emeritus
Amel School www.amelschool.com
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970


On Sat, Mar 31, 2018, 05:43 philipp.sollberger@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Dear experienced AMEL Yacht Owners,


Does anybody has experience in rescueing a casualty on Super Maramus? I'm instructor for ISAF courses and I'm thinking about the method for taking back on board a person who was fallen over board.

We have several possibilities to board somebody. 

Halyard of the balooner is for sure strong enough.

Halyard from the top from the spinnaker halyard. Is the fixation on mast with the shakle on the block strong enough to lift up a person in full wet suit with wet boots etc with a weight of about 150 kg?

What about the main mast with the boom? Is the steel wire which holds the boom, strong enough to lift up 150 kg or more?

Last but not least on the mizzen we can use the halyard for the mizzen staysail. Same question: Is the mizzen mast fixation on the top with shakle and block strong enough for lifting up 150 kg or more?

The last possibility is the halyard for the outboard or passerelle with the boom of the mizzen. Is this fixation strong enough to lift up 150 kg or more.


All your answer will be appreciated strongly and I thank you all very much for your ideas and thoughts about the subject which each us hopes it will never happen.

By the way: the AMEL 55 and later have a vang on the boom, which is the method for lifting up a person from the water.


From the RYA there is the recommendation, that casualty should lift up horizontally and for this you need a second halyard or the same one halyard but you need the strength of the double weight.


Many thanks an fair winds,


Philipp 

#124 SM Félicie




Re: [Amel Yacht Owners] Re: Rats!

Mark Erdos
 

Tastes like chicken!

 

 

With best regards,

 

Mark

 

Skipper

Sailing Vessel - Cream Puff - SM2K - #275

Currently cruising - Guadeloupe

www.creampuff.us

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Saturday, March 31, 2018 4:42 AM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Re: Rats!

 

 

Whoa!!!!  Guinea Pigs are related to rats and mice, and they're part of the food chain in Ecuador?   I'm not that hungry!

 

Duane


Re: [Amel Yacht Owners] Rescueing method of casualty (Person Over Board)

James Studdart
 

Can anyone elaborate on why the RYA suggests people are lifted horizontally? I find that hard to believe. The idea of using two lines to lift a casualty out of the water fills me with dread of tangles, loops and over complication. Why double weight? Surely a wet person weighs the same vertical or horizontal.

Cheers,
James
SV SeaBean, SM344
Moorea

On Sat, Mar 31, 2018 at 00:22 Bill Rouse brouse@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Phillip,

I believe that the way the Super Maramu was designed, rigged, and equipped, it may be superior to any other sailboat regarding your rescue questions.

The mizzen mast was rigged with 2 each 10mm halyards (1 port and 1 stbd) each capable of lifting at least 1000 pounds. Each can be hauled using the electric main sheet winch. More importantly, there is a block for each at the end of the mizzen boom which will aid in holding the retrieved person off the boat. With the mizzen sheet loose, the end of the  mizzen boom will elevate when the halyard shackle meets the boom block, allowing you to swing the boom and person up and over the rail.

However, all above is based on how the Super Maramu was designed and built and may not be true with a particular Super Maramu owned by a non-caring owner, or a smarter person than Henri Amel.I hope this helps you. If you need more information, please contact me. 

Best,

CW Bill Rouse
Admiral, Texas Navy
Commander Emeritus
Amel School www.amelschool.com
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970


On Sat, Mar 31, 2018, 05:43 philipp.sollberger@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Dear experienced AMEL Yacht Owners,


Does anybody has experience in rescueing a casualty on Super Maramus? I'm instructor for ISAF courses and I'm thinking about the method for taking back on board a person who was fallen over board.

We have several possibilities to board somebody. 

Halyard of the balooner is for sure strong enough.

Halyard from the top from the spinnaker halyard. Is the fixation on mast with the shakle on the block strong enough to lift up a person in full wet suit with wet boots etc with a weight of about 150 kg?

What about the main mast with the boom? Is the steel wire which holds the boom, strong enough to lift up 150 kg or more?

Last but not least on the mizzen we can use the halyard for the mizzen staysail. Same question: Is the mizzen mast fixation on the top with shakle and block strong enough for lifting up 150 kg or more?

The last possibility is the halyard for the outboard or passerelle with the boom of the mizzen. Is this fixation strong enough to lift up 150 kg or more.


All your answer will be appreciated strongly and I thank you all very much for your ideas and thoughts about the subject which each us hopes it will never happen.

By the way: the AMEL 55 and later have a vang on the boom, which is the method for lifting up a person from the water.


From the RYA there is the recommendation, that casualty should lift up horizontally and for this you need a second halyard or the same one halyard but you need the strength of the double weight.


Many thanks an fair winds,


Philipp 

#124 SM Félicie




SM Keel bolts

ianjenkins1946 <ianjudyjenkins@hotmail.com>
 

 Hi all,


Does anyone know the diameter of the keel bolt in the grey water bilge in the engine room of an SM ? I am making up the copper strip that bolts on to the aft bolt but I'm not on board and don't know how big to make the hole on the copper strip.


     Ian and Judy,

 Pen Azen, SM 302, Preveza, Greece


Re: [Amel Yacht Owners] Re: Dessalator pump not working

Mohammad Shirloo
 

Hi Mark
 
On our high pressure pump there are two capacitors.
 
  • One is black 180 microfarad -0-20%, 220VAC, 40-60HZ FACON 70906.1412
  • One is white 70 microfarad +/-5% AC400V B, AC 450V C, 40/085/21 50-60 Hz ICAR Ecofill R-06-49A.
 
Let me  know if I can be of any other help.
 
Respectfully;
Mohammad and Aty
B&B Kokomo
Amel 54 #099
 


From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Saturday, March 31, 2018 7:54 AM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Re: Dessalator pump not working

 

Did you come up with the correct size capacitor for your watermaker?  I have a 160 liter per hour version and the capicator is painted obstructing the name plate.  Any information would be appreciated.  Thanks.

Mark Mueller
A54 - 68 
Brass Ring
Ft. Lauderdale


Re: [Amel Yacht Owners] Hurricane season SET UP

eric freedman
 

Hi Alessandro,

I attach about 100 feet of line to the swivel at the top of the foil.

I then rotate the foil until it is covered in line from top to bottom..

The end of the line I attach tightly to the end of the boom.

No noise and no banging.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Saturday, March 31, 2018 7:55 AM
To: amelyachtowners@...
Subject: [Amel Yacht Owners] Hurricane season SET UP

 

 

Hi All,

I'm setting up my GRAND CRU for the Hurricane Season and , of course, I wish to remove all the sails: I'm looking around a SMART IDEA to avoid the furling bumping inside the masts (main and mizzen) when they are without the sails. 

I'd appreciate the all folks  ideas  smarter than me.

Fair winds

Alessandro

GRAND CRU SM #443 


Re: [Amel Yacht Owners] Re: Dessalator pump not working

Mark & Debbie Mueller
 

Did you come up with the correct size capacitor for your watermaker?  I have a 160 liter per hour version and the capicator is painted obstructing the name plate.  Any information would be appreciated.  Thanks.

Mark Mueller
A54 - 68 
Brass Ring
Ft. Lauderdale


Re: [Amel Yacht Owners] Installation second autopilot

eric freedman
 

Niklas,

The chain and sprockets are stock. They are available from many parts supply houses worldwide.

You just might have to have the mounting hole and keyway  machined to fit.

This is a company I use in the USA.

Fair Winds

Eric

Kimberlite Amel Super Maramu #376

https://www.mcmaster.com/#roller-chain-sprockets/=1c7k75i

 

 

From: amelyachtowners@... [mailto:amelyachtowners@...]
Sent: Friday, March 30, 2018 1:10 AM
To: amelyachtowners@...
Subject: Re: [Amel Yacht Owners] Installation second autopilot

 

 

Hello Steve

 

Thank you, i already have the rotary drive so i try to find a company that sell the chain and sprocket. I think i already have the keyway on the steering shaft. i am going to se if amel have any sprocket left maybe i am lucky.

 

Regards

Niklas SY Nipe sm2k#333

 

2018-03-29 19:39 GMT+02:00 Stephen Davis flyboyscd@... [amelyachtowners] <amelyachtowners@...>:

 

Hello Niklas,

 

I’m a little surprised you do not have a rotary drive, as I’ve seen many SMs, and they all had one. I’d be curious to know how many of you out there do not have a rotary drive. I own hull #72 (1992), and at that time the boats only came with a rotary drive, and at a later hull number Amel re-designed the rudder quadrant to accept a linear drive. 

 

If you decide to add a Rotary drive, you need to find a Raymarine type II 24 volt drive. The 12 volt drives are usually in stock here in the USA, but a 24 volt version is hard to find. I purchased a new 24v drive from Raymarine USA about a year and a half ago, and it was the last on they had to sell at that time. I suspect if you talk to the right person at Raymarine they can find you one, but you may have to wait a bit. 

 

With regards to the sprockets, on my boat the drive sprocket on the rotary drive is 19 teeth, and on the steering shaft it is 38 teeth. No guarantees the newer boats are the same, but I suspect they are. I just purchased a new steering shaft and sprocket for the shaft from Maude, and she was surprised to find they still had the shaft 38 tooth sprocket on the shelf. It sounded like I got the last sprocket, but you would have to ask Maude to be sure. Amel does not have the rotary drive sprocket or the chain. Raymarine actually has a part number for the drive sprocket, but when I spoke to them, they said they no longer sell them. I’m sure the drive sprocket could be found from some industrial supply place, but so far, all the ones I’ve found have a keyway slightly to wide for the shaft. I’m also looking for a new chain as a spare, but have not found one yet. If anyone has a source or the exact specs on the chain, please let me know. 

 

I’m assuming since your boat did not come with a rotary drive, your steering shaft does not have a keyway machined in it to hold the sprocket. If that is the case, you will have to completely disassemble the steering system, take the steering shaft to a machine shop, and have a keyway machined into it. You can’t do this until you have the new drive mounted, and can check the exact alignment of the the sprocket on the drive to the shaft. I just purchased a new steering shaft and steering racks from Amel, and was surprised the new shaft did not come with the keyway machined into it, and I had to have a machine shop do it for me.

 

As you can see, to add a rotary drive now will require some effort and expense. If it were me, I’d probably purchase a spare Linear drive which you should be able to change out in a half hour. 

 

Best of luck with your project. 

 

Regards,

 

Steve Davis

Aloha SM 72

KoOlina, Hawaii

 

Steve Davis

S/V Aloha


On Mar 28, 2018, at 10:12 PM, gloggler@... [amelyachtowners] <amelyachtowners@...> wrote:

 

Hello

 

Im going to install Raymarine rotary drive type 2 24v as a second autopilot and wonder if anybody knows the size on steering sprocket, drive sprocket and chain and were i can it? Have been in contact with Amel but they did not know.

 

Regards Niklas Glöggler SY Nipe SM2K #333



 

--

Niklas Glöggler


Re: Hurricane season SET UP

Craig Briggs
 

Why remove the main and mizzen? Remove their outhaul lines and completely furl the sails into the masts so nothing is sticking out to be blown by the wind (nor damaged by UV).
Cheers, Craig SN68 


---In amelyachtowners@..., <grandcru443@...> wrote :

Hi All,

I'm setting up my GRAND CRU for the Hurricane Season and , of course, I wish to remove all the sails: I'm looking around a SMART IDEA to avoid the furling bumping inside the masts (main and mizzen) when they are without the sails. 

I'd appreciate the all folks  ideas  smarter than me.

Fair winds

Alessandro

GRAND CRU SM #443 


Re: Hurricane season SET UP

Paul Osterberg
 

We attached a three strand rope to the top furler hoist it and then furl about 10 revs then the rope will act as a dampers no noice from the foil.
Paul on sykerpa SM 259


Re: Hurricane season SET UP

Ian Park
 

Attach a 12 or 14 mm rope to the halliard. Hoist it up the mast and furl while guiding the furled rope from top to bottom. When two thirds down the mast pull the remainder to the end of the boom and tighten off on the cleat. This pulls the wrapped foil against the slot and stops the banging.

Ian

Ocean Hobo SN96. Antigua


Hurricane season SET UP

grandcru443@...
 

Hi All,

I'm setting up my GRAND CRU for the Hurricane Season and , of course, I wish to remove all the sails: I'm looking around a SMART IDEA to avoid the furling bumping inside the masts (main and mizzen) when they are without the sails. 

I'd appreciate the all folks  ideas  smarter than me.

Fair winds

Alessandro

GRAND CRU SM #443 


Amel 50 review

ianjenkins1946 <ianjudyjenkins@hotmail.com>
 

Hi All,


 There is a great review of the Amel 50 in April's Yachting World--she's on the front cover as well.


The reviewer is Pip Hare. We first met Pip in Piriapolis , Uruguay, where she had sailed two handed in The Shed,  an Oyster 37 which had seen better days. She decided to do the OSTAR, the single-handed transatlantic race, so she sailed back singlehanded from Uruguay to UK and set off on the race. Somewhere to the west of Ireland a lower shroud parted. Mast swaying,  she nursed the boat back to a bay on the south cost of Ireland where her father rowed out to her with a new stay. She wasn't allowed shore assistance beyond that ,so she had to rerig the boat herself . She set off in pursuit of her class who by now had 2-3 days lead on her. She overhauled most of them.

 Pip went on to compete  successfully in those crazy 30 footers which the French love, on races like the Route du Rhum and is probably at her happiest single handed in mid-Atlantic up to her waist in cold sea water, in the dark,  in the cockpit having just broached while trying to maintain 17 knots when her competitors have eased back to 10.


 So, you might wonder what on earth she would make of the Amel 50.  It was December,  dark, wet and windy off La Rochelle. She confesses that did feel overdressed sitting in the cockpit in her salopettes and seaboots ( remember them ?) with warmth rising from the saloon together with the aroma of bread and fresh coffee...


 Her conclusion:  " I can't sit on the fence about the Amel 50; it's a brilliant boat.........I arrived with some heavy preconceptions, perhaps about as much as the kind of sailor I am as the kind of boat I would be sailing. I was treated to the full Amel experience.... but if you take away the fine food, endless expressos and crisp white bed linen, the Amel still shines. It sails well, it is beautifully built and it made me smile. I left surprised and ever so slightly in love "


 Praise indeed ! I think the La Rochelle yard is going to be very busy.


 Ian and Judy,

 Pen Azen, SM 302, Preveza, Greece


Re: [Amel Yacht Owners] Rescueing method of casualty (Person Over Board)

 

Phillip,

I believe that the way the Super Maramu was designed, rigged, and equipped, it may be superior to any other sailboat regarding your rescue questions.

The mizzen mast was rigged with 2 each 10mm halyards (1 port and 1 stbd) each capable of lifting at least 1000 pounds. Each can be hauled using the electric main sheet winch. More importantly, there is a block for each at the end of the mizzen boom which will aid in holding the retrieved person off the boat. With the mizzen sheet loose, the end of the  mizzen boom will elevate when the halyard shackle meets the boom block, allowing you to swing the boom and person up and over the rail.

However, all above is based on how the Super Maramu was designed and built and may not be true with a particular Super Maramu owned by a non-caring owner, or a smarter person than Henri Amel.I hope this helps you. If you need more information, please contact me. 

Best,

CW Bill Rouse
Admiral, Texas Navy
Commander Emeritus
Amel School www.amelschool.com
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970


On Sat, Mar 31, 2018, 05:43 philipp.sollberger@... [amelyachtowners] <amelyachtowners@...> wrote:
 

Dear experienced AMEL Yacht Owners,


Does anybody has experience in rescueing a casualty on Super Maramus? I'm instructor for ISAF courses and I'm thinking about the method for taking back on board a person who was fallen over board.

We have several possibilities to board somebody. 

Halyard of the balooner is for sure strong enough.

Halyard from the top from the spinnaker halyard. Is the fixation on mast with the shakle on the block strong enough to lift up a person in full wet suit with wet boots etc with a weight of about 150 kg?

What about the main mast with the boom? Is the steel wire which holds the boom, strong enough to lift up 150 kg or more?

Last but not least on the mizzen we can use the halyard for the mizzen staysail. Same question: Is the mizzen mast fixation on the top with shakle and block strong enough for lifting up 150 kg or more?

The last possibility is the halyard for the outboard or passerelle with the boom of the mizzen. Is this fixation strong enough to lift up 150 kg or more.


All your answer will be appreciated strongly and I thank you all very much for your ideas and thoughts about the subject which each us hopes it will never happen.

By the way: the AMEL 55 and later have a vang on the boom, which is the method for lifting up a person from the water.


From the RYA there is the recommendation, that casualty should lift up horizontally and for this you need a second halyard or the same one halyard but you need the strength of the double weight.


Many thanks an fair winds,


Philipp 

#124 SM Félicie




Rescueing method of casualty (Person Over Board)

philipp.sollberger@...
 

Dear experienced AMEL Yacht Owners,


Does anybody has experience in rescueing a casualty on Super Maramus? I'm instructor for ISAF courses and I'm thinking about the method for taking back on board a person who was fallen over board.

We have several possibilities to board somebody. 

Halyard of the balooner is for sure strong enough.

Halyard from the top from the spinnaker halyard. Is the fixation on mast with the shakle on the block strong enough to lift up a person in full wet suit with wet boots etc with a weight of about 150 kg?

What about the main mast with the boom? Is the steel wire which holds the boom, strong enough to lift up 150 kg or more?

Last but not least on the mizzen we can use the halyard for the mizzen staysail. Same question: Is the mizzen mast fixation on the top with shakle and block strong enough for lifting up 150 kg or more?

The last possibility is the halyard for the outboard or passerelle with the boom of the mizzen. Is this fixation strong enough to lift up 150 kg or more.


All your answer will be appreciated strongly and I thank you all very much for your ideas and thoughts about the subject which each us hopes it will never happen.

By the way: the AMEL 55 and later have a vang on the boom, which is the method for lifting up a person from the water.


From the RYA there is the recommendation, that casualty should lift up horizontally and for this you need a second halyard or the same one halyard but you need the strength of the double weight.


Many thanks an fair winds,


Philipp 

#124 SM Félicie




Re: Rats!

Duane Siegfri
 

Whoa!!!!  Guinea Pigs are related to rats and mice, and they're part of the food chain in Ecuador?   I'm not that hungry!

Duane

19681 - 19700 of 58498