Hi Chris, Thanks for your suggestions I have 12 new DEKA lead acid deep cycle batteries. About 630 Ah. My Dolphin 30 A charger works slowly up to 28.1,2 v. Than, I suppose, it should go down to about

To all, first thanks a lot to all for help and suggestions . Short story : After a terrible Screech, Screech noise I explored the bottom of the motor where there is the connection with the black plast

Sorry Malcom, when I remove the 4 studs the end housing comes out along the axis with the bearing or the bearing remain fixed to the axis? It seams that the circlips link the bearing to end housing an

Ok Phillips thanks for support., Lukily the motor is working properly, no water inside. I'm very interested in "The end housing can then be removed and the bearing replaced" How did you proceed ? Did

To all, the problem I have is the breakage of ball bearing inside the bottom part of motor, not in side the feet. The bearing is where the axis goes out of body motor. I wish to know if some one has r

Hi Bill and Gary, sorry I don't understand : among the photos " Bow thruster service" I see a ball bearing rusty brown, it seems broken or it is only very dirty ? Gianni

Hi Gary, i have seen your and BEBE photos about bow thruster service. I'm now in Colon Panama waiting to cross westbound and I have the ball bearing broken as you had. I'm waiting an answer from Amel

Hello all, do you know, please, the correct o-ring sizes ? I found the bearings , not the seals. SAV AMEL doesn't any more supply the kit. Thanks for infos and suggestions Giovanni Testa sv EUTIKIA SM

HI ALL< about subjet I found this as records : Hello all: The overhaul kit sent to my by Olivier Beaute of Amel included the following: Bearing: SKF 6201 Quantity One Bearing: SKF 6006-2RS1 Quantity T

Bill, I have contacted the main B&G support in Viareggio. They told me that the neoprene extension is mainly for protection of the transducer. For now you can sail but you have to keep it cleaned, obv

Hi Bill, go to http://www.bandg.com/upload/BandG/Documents/Manuals/sonicinstall.pdf It is a Manual we have not normally on board. There is a sketch of the sensor and of its neoprene cap. Tomorrow - to

Hi to all, thanks so much Tom and Wolfgang for infos for storage in Raiatea. I wrote to CNI, but for now no answer. Wolfgang, where are you ? Wich was your route ? All the best Gianni EUTIKIA SM2K 428

Hi to all, for the next season, from October 2011 to March 2012, I'm planning to leave on the hard at Raiatea my boat Eutikia. Ther'are two possibilties : Raiatea Carenage Services and Chantier Naval

HI, I had the same problem : the lock ring lost and the lamp crashed sailing on the deck ! Aquasignal has now a new version but I wrote to Kohlhoff Thea <Kohlhoff@...> ,very kind Internation

Hi to all, wich is your experience with Autohelm ST7001 plus > Dealer Calibration > Rudder Gain ? I had to replace my Course Computer and I found that the Rudder Gain value was "2" !? It was the first

Hi, on the orange disco part in front of the black cilinder there are 2 very little dots, very very difficult to see, counting the ring ahead and reverse . Well these are dirty ! Clean it with a littl

Hi to all, thanks Jlm, but unlukily the system works unproperly for me. In attached what appears on my pc. Any suggestion ? Thanks to all Giovanni

hi to all, I cannot open correctly the "photo" section on forum site. I see only little frame with red cross. Do you know if the "forum" is working properly Thanks Giovanni Testa s/v EUTIKIA SM2K 428

Hi Richard, thanks so much for your support , always very prompt and rich of suggestions. Now I know better the great Amel people around the world also thanks to you. All the best and...Buon Vento ! G

Hi, Thanks Richard. Now I'm at home in Venezia , but next November I'll be again on board in Puerto la Cruz ( Venezuela) and I'll test it at the first sailing. All the best Giovanni&Marina TESTA EUTIK